Viking RDSCG230-5B Service Manual
  1. Manuals
  2. Brands
  3. Viking Manuals
  4. Ranges
  5. RDSCG230-5B
  6. Service manual

Viking RDSCG230-5B Service Manual

30 inch self-clean
Hide thumbs Also See for RDSCG230-5B:
Table of Contents

Advertisement

Quick Links

See also: Installation Manual , Manual
Service
®
Preferred Service
Manual
This manual is to be used by qualified appliance technicians only. Viking
does not assume any responsibility for property damage or personal
injury for improper service procedures done by an unqualified person.
30 Inch
This Base Manual covers general and
specific information including, but not
Self-Clean
limited to the following models:
RDSCG230-5B
Gas Range
SMC-0029
July 2012

Advertisement

Table of Contents
loading

Related Manuals for Viking RDSCG230-5B

Summary of Contents for Viking RDSCG230-5B

  • Page 1 Service ® Preferred Service Manual This manual is to be used by qualified appliance technicians only. Viking does not assume any responsibility for property damage or personal injury for improper service procedures done by an unqualified person. 30 Inch This Base Manual covers general and...

  • Page 2: Table Of Contents

    Bake Burner Removal ..........22 Broil Burner and Igniter Removal ......22 Bake or Broil Burner Orifice Removal ....23 Convection Fan Assembly Removal ...... 23 Control Components Accessed ......23 Control Panel Assembly Removal ......23 ©2012 Viking Preferred Service...

  • Page 3: Important Information

    All safety messages will be preceded by the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These words mean: VIKING will not be responsible for any injury or property damage from improper service procedures. If performing service on your own product, you must...

  • Page 4: General Information

    13. One 12,000 BTU burner 14. One 18,000 dual stacked BTU burner 15. One 17,000 BTU burner 16. One 8,000 BTU burner 17. Identification plate 18. Three full extension glide racks/Six rack positions 19. Broiler pan (located inside oven) ©2012 Viking Preferred Service...

  • Page 5: Warnings

    ©2012 Viking Preferred Service...

  • Page 6: Cleaning Safety

    BURN OR ELECTRICAL SHOCK HAZARD. Make may be equally harmful. sure all controls are OFF and oven is COOL before cleaning. Failure to do so can result in burns or electrical shock. ©2012 Viking Preferred Service...

  • Page 7: Before Using Range

    When the insulation is thoroughly cured, this odor will disappear. During subsequent self-cleaning cycles, you may sense an odor characteristic of high temperatures. KEEP THE KITCHEN WELL-VENTED DURING THE SELF-CLEAN CYCLE. ©2012 Viking Preferred Service...

  • Page 8: Troubleshooting

    Gas solenoid fault. Check wiring and gas solenoid. 7 flashes every 4 seconds Power up with channel on. Switch channel off and retry. 8 flashes every 4 seconds Gas solenoid fault. Check wiring and gas solenoid. Direct Spark Module (DSI Board) Connections ©2012 Viking Preferred Service...

  • Page 9: Led Error Codes

    1 second ON, 1 second OFF (Oven Probe) Model 2 flashes, then 4 seconds OFF A/D Stuck 3 flashes, then 4 seconds OFF Fan Hall 4 flashes, then 4 seconds OFF Self-Cleaning Oven Control Board Connections ©2012 Viking Preferred Service...

  • Page 10: Component Characteristics

    120 VAC Not Applicable On Single Point Spark Module - black to white Module *Resistance checks made with power off. **High limit switch is N.C. (normally closed) and opens at 275°F, resets at 250°F (+/- 10°F). ©2012 Viking Preferred Service...

  • Page 11: Checking Oven Bake Operation

    Replace DSI module if no voltage is present. If voltage is present on control board and DSI module, disconnect power to the range. If voltage is present, check bake solenoid (see Checking Solenoid Operation). ©2012 Viking Preferred Service...

  • Page 12: Checking Oven Broil Operation

    Replace DSI module if no voltage is present. If voltage is present on control board and DSI module, disconnect power to the range. If voltage is present, check broil solenoid (see Checking Solenoid Operation). ©2012 Viking Preferred Service...

  • Page 13: Checking Solenoid Operation

    S2. When the door is fully opened, S1 is closed by the motor cam. This will signal the board that the door is unlocked. Replace the solenoid if the resistance is not close. ©2012 Viking Preferred Service...

  • Page 14: Testing Lock Motor

    (∞) when the door is unlocked. Orange Orange Blue Blue White/Green White/Green Motor Motor S2 bottom S2 bottom Note: (S3 - top switch not shown) Note: (S3 - top switch not shown) ©2012 Viking Preferred Service...

  • Page 15: Rtd Sensor

    RTD. If the RTD test opened. resistance is within specifications and the consumer is having erratic oven temperatures, please call Viking Technical support (1-800-914-4799) for assistance. ©2012 Viking Preferred Service...

  • Page 16: Spark Module Test

    (If open, replace wire.) replace wire.) 10. If 120 VAC is present in step 5 and the black igniter 11. If 0 ohms present in step 10, replace the spark wire has continuity, replace the spark module. module. ©2012 Viking Preferred Service...

  • Page 17: Troubleshooting Guide

    Oven cycle or clean light inoperable - Defective cycle or clean light Replace light oven, surface burner igniters operate (neon) Open oven control board Replace oven control board Defective oven wiring (shorted, Repair or replace defective wiring open, or burned) ©2012 Viking Preferred Service...

  • Page 18: Surface Burners

    1. Access control components (see Access Control Components Assembly). 2. Disconnect Molex connector to remove power to the range. 3. Reverse procedure for installation. ©2012 Viking Preferred Service...

  • Page 19: Selector And Thermostat Characteristics

    9.40 kW 2.98 kW 6.43 kW Broil 9.40 kW 1.97 kW 7.56 kW Clean 9.40 kW 722 W 8.85 kW Resistance checks are made on the control panel wire harness with the control panel wire harness disconnected. ©2012 Viking Preferred Service...

  • Page 20: Disassembly

    " hex head 3. Lift the inner door panel assembly from the outer Allen wrench. Tighten hinge trim screws after door panel assembly. adjustment is made. 4. Reverse procedure for installation. 5. Reverse procedure for installation. ©2012 Viking Preferred Service...

  • Page 21: Door Handle Removal

    7. Lift inner glass from inner door panel. 8. Remove black fiberglass rope from inner door panel. Note: Use care with insulation; make sure to replace any damaged or missing insulation. 9. Reverse procedure for installation. ©2012 Viking Preferred Service...

  • Page 22: Door Hinge Removal

    5. Remove screw and igniter from broil burner. 4. Disconnect wire from igniter. 5. Remove screw and igniter from bake burner. (View of top of oven cavity) 6. Reverse procedure for installation. 6. Reverse procedure for installation. ©2012 Viking Preferred Service...

  • Page 23: Bake Or Broil Burner Orifice Removal

    5. Remove left hand nut and fan blade from convection fan. Control Panel Assembly Removal 1. Access control components (see Control Components Accessed). 2. Mark and disconnect all connectors to remove control panel from range. 6. Reverse procedure for installation. 3. Reverse procedure for installation. ©2012 Viking Preferred Service...

  • Page 24: Oven Function Selector Removal

    3. Disconnect two connectors from the indicator light. 1. Access control components (see Control Components Accessed). 2. Disconnect connector from the oven thermostat. 3. Remove screws, bezel, and thermostat from control panel. 4. Reverse procedure for installation. 4. Reverse procedure for installation. ©2012 Viking Preferred Service...

  • Page 25: Dsi Module And Control Board Accessed

    4. Mark and disconnect connectors from door switch. Note: During installation, make sure all wires are connected and are not pinched between the component tray and burner box. 6. Reverse procedure for installation. 5. Reverse procedure for installation. ©2012 Viking Preferred Service...

  • Page 26: High Limit Switch Removal

    2. Disconnect connectors from valve switch. 1. Access control components (see Control 3. Pull to remove valve switch from burner valve. Components Accessed). 2. Remove screws from component tray and door lock assembly. 4. Reverse procedure for installation. ©2012 Viking Preferred Service...

  • Page 27: Surface Burner Valve Removal

    2. Remove screws and rack support from holes in back assembly. wall of oven cavity. 6. For the stack burner valve, pull to remove the valve switch from the valve. 3. Reverse procedure for installation. 7. Reverse procedure for installation. 8. Perform gas leak test. ©2012 Viking Preferred Service...

  • Page 28: Oven Light Bulb Removal

    1. Remove grates, burner caps, and burner heads from burner base assembly. 2. Remove orifice from jet holder. Note: Make sure to return insulation to original position under each side trim. 7. Reverse procedure for installation. 3. Reverse procedure for installation. ©2012 Viking Preferred Service...

  • Page 29: Jet Holder Removal

    5. Remove inverted screws from jet holder. 7. Remove screws, main top support, and side panel 6. Lift jet holder to remove from tubing. from range. 7. Reverse procedure for installation. 8. Perform gas leak test. 8. Reverse procedure for installation. ©2012 Viking Preferred Service...

  • Page 30: Back Panel Removal

    5. Reverse procedure for installation. Side Light Housing Removal 1. Remove back panel (see Back Panel Removal). 4. Remove screws and hinge receiver from range. 2. Disconnect connector for side light housing. 5. Reverse procedure for installation. ©2012 Viking Preferred Service...

  • Page 31: Gas Solenoid Valve Removal

    4. Remove screws and solenoid valve from range. 6. Reverse procedure for installation. 5. Reverse procedure for installation. Note: Use approved sealant when installing pressure 6. Perform gas leak test. regulator. 7. Perform gas leak test. ©2012 Viking Preferred Service...

  • Page 32: Temperature Sensor (Rtd) Removal

    5. Route RTD wires through burner box area and out 5. Mark and disconnect three connectors and remove back of range. blower motor. 6. Reverse procedure for installation. 6. Remove screws and RTD sensor from the oven liner. 7. Reverse procedure for installation. ©2012 Viking Preferred Service...

  • Page 33: Wiring Diagrams

    Wiring Diagrams Wiring Diagram RDSCG230-5B Self-Clean Gas Range ©2012 Viking Preferred Service...

Table of Contents