Table of Contents
Advertisement
forward rotation function. To rotate open the zip located at the top of the canopy.
The canopy has a fully ratcheting function to create complete coverage. Simply pull on the
front of the canopy to the desired position. The height can be easily adjusted by simply
sliding the canopy up or down the frame. The entire canopy can also be tilted forward. For
maximum coverage, unzip the extra panel on top of canopy and pull forward.
– The canopy flap at the rear of the stroller can be rolled up and fixed with a velcro
fastener, if required.
11. USING THE HaRNESS SYSTEm
a) To fasten the harness system connect the waist buckle and the shoulder buckle on the
left and right side of the harness. Plug both connected elements into the crotch buckle.
b) To tighten the belts pull the strap on the front of the central harness buckle
c) To release the belt system press the release button located on the seat in front of the
belt lock while pulling at the shoulder belts.
d) To open the buckle press the button located in the center of the harness buckle. To
disassemble the harness system completely, separate the elements connecting the
chest belt and the waist belt by pulling them aside
e) Adjust the length of the crotch strap with the corresponding slider
WarNING
aLWaYS USE THE CRoTCH STRaP IN ComBINaTIoN WITH
THE WaIST BELT.
12. aDJUSTING THE HaRNESS SYSTEm FoR NEWBoRNS
a) Release the loops at the end of the shoulder straps from the triangle in the belt system,
situated at the bottom of the backrest under the seat cover.
b) Completely pull the shoulder straps out of the holes in the backrest.
c) Feed the shoulder straps through the two bottom holes. Make sure to feed the straps
back through the holes in the backrest mechanism and re-attach them to the triangle.
d) To adjust the length of the shoulder straps to newborns please attach the inner loop of
the shoulder strap ends to the triangular ring. Switch back to the upper holes as soon as
the shoulder straps do no longer fit over the child´s shoulders.
13. REmoVING THE HEaDHUGGER aND SHoULDER PaDS (ToPaz oNLY)
Remove the headhugger as soon as the headhugger does no longer fit over the child´s
shoulders.
a) Remove the velcros of the headhugger on the top leh and right side on the back of the
seat cover.
b) Release the loops at the end of the shoulder straps from the triangle in the belt system,
situated at the bottom of the backrest under the seat cover.
c) Completely pull the shoulder straps out of the holes in the backrest.
d) Pull the shoulder straps through the shoulder pads and the headhugger. Make sure to
feed the straps back through the holes in the backrest mechanism and attach them to
the triangle. You can use the headhugger and the shoulder pads separately.
14. REmoVING THE SEaTCoVER
a) Slightly fold the stroller to reduce tension.
b) Remove the canopy from the stroller, if attached.
c) Take the seat cover's hooks (3) off the frame on left and right side
d) Open the press buttons (4) of the straps connected to the seat side panels and the
basket rear tube.
e) Open the flaps (5) which are fixed with velcro over the tubes, one on each side.
f) Feed the strap with the slider (6) of the central harness buckle through the hole in the
seat fabric.
g) Feed the loops on the end of the shoulder straps through the triangle in the backrest
(7).
h) Feed the shoulder straps through the holes in the seat fabric (8).
i) Open the press buttons which are on the left and the right side from the seat on the
bottom from the fabric.
j) Pull the seat cover over the belt shifting button on the seat.
k) Slide the fabrics from the seat base tubes.
l) Reverse this procedure to refit the seat cover and the harness. Make sure that the seat
tubes slide back into the pockets inside the seat cover.
15. RECLINING THE LEG REST
a) Press the leg rest on both front edges and push down.
b) Simply lift the leg rest to put it back to the starting position.
16. RECLINING THE SEaT
a) Pull the recline lever at the back of the seat in order to recline the backrest to the 4
different positions.
b) To raise lift the complete backrest up to required position.
17. CaRRYING THE STRoLLER
– Pull the flexible carring handle on right rear tube and lift the stroller.
18. aTTaCHING THE RaINCoVER (oPTIoNaL)
a) Extend the rain cover over the stroller like shown in the image
b) To fit the rain cover fasten the velcro strips around the frame at the top and bottom on
both sides of the buggy.
19. CaRE INSTRUCTIoNS
– wash separately
– gentle action wash warm water
– do not bleach
– do not tumble dry
– do not iron
– do not dry clean
5
Advertisement
Table of Contents
