Canopy; Using The Harness System; Adjusting The Harness System For Newborns; Removing The Headhugger And The Shoulder Pads (Topaz Only) - CYBEX TOPAZ User Manual

10. ExTENDAbLE CANOpY
- attach the canopy adaptor on to the inside of the frame tubes of the
buggy.
- To remove the canopy reverse procedure.
- Extend the canopy and place canopy rear flap behind the seat.
- use the zipper to attach or detach the winter extension
- Lie-flat position: Put the rear flap over the seat's back rest and fixate it
with the two velcros underneath.
- The canopy is adjustable to various positions. The Canopy has a height
adjustment and a forward rotation function. To rotate open the zip
located at the top of the canopy.
The canopy has a fully ratcheting function to create complete coverage.
Simply pull on the front of the canopy to the desired position. The
height can be easily adjusted by simply sliding the canopy up or down
the frame. The entire canopy can also be tilted forward. for maximum
coverage, unzip the extra panel on top of canopy and pull forward.
- The canopy flap at the rear of the stroller can be rolled up and fixed
with a velcro fastener, if required.

11. USING THE HARNESS SYSTEM

a) To fasten the harness system insert left and right side fasteners into
the central harness buckle.
b) To tighten the belts pull the strap on the front of the central harness
buckle.
c) To release the belt system press the release button located on the seat
in front of the belt lock while pulling at the shoulder belts.
d) To release the fasteners squeeze the grooves on left and right side of
the central harness buckle.
e) adjust the length of the crotch strap with the corresponding slider.
waRnInG: alwaYS uSE THE CROTCH STRap In
COmBInaTIOn wITH THE waIST BElT.

12. ADjUSTING THE HARNESS SYSTEM FOR NEWbORNS

a) Release the loops at the end of the shoulder straps from the triangle in
the belt system, situated at the bottom of the backrest under the seat
cover.
b) Completely pull the shoulder straps out of the holes in the backrest.
c) feed the shoulder straps through the two bottom holes. make sure to
feed the straps back through the holes in the backrest mechanism and
re-attach them to the triangle.
d) To adjust the length of the shoulder straps to newborns please attach
the inner loop of the shoulder strap ends to the triangular ring. Switch
back to the upper holes as soon as the shoulder straps do no longer fit
over the child´s shoulders.
13. REMOvING THE HEADHUGGER AND SHOULDER pADS
(TOpAz ONLY)
Remove the headhugger as soon as the headhugger does no longer fit
over the child´s shoulders.
a) Remove the velcros of the headhugger on the top left and right side on
the back of the seat cover.
b) Release the loops at the end of the shoulder straps from the triangle in
the belt system, situated at the bottom of the backrest under the seat
cover.
c) Completely pull the shoulder straps out of the holes in the backrest.

14. REMOvING THE SEATCOvER

a) Slightly fold the stroller to reduce tension.
b) Remove the canopy from the stroller, if attached.
c) Take the seat cover's hooks (3) off the frame on left and right side
d) Open the press buttons (4) of the straps connected to the seat side
panels and the basket rear tube.
e) Open the flaps (5) which are fixed with velcro over the tubes, one on
each side.
f) feed the strap with the slider (6) of the central harness buckle through
the hole in the seat fabric.
g) feed the loops on the end of the shoulder straps through the triangle in
the backrest (7).
h) feed the shoulder straps through the holes in the seat fabric (8).
i) Open the press buttons which are on the left and the right side from the
seat on the bottom from the fabric.
j) pull the seat cover over the belt shifting button on the seat.
k) Slide the fabrics from the seat base tubes.
l) Reverse this procedure to refit the seat cover and the harness. Make
sure that the seat tubes slide back into the pockets inside the seat
cover.

15. RECLINING THE LEG REST

a) press the leg rest on both front edges and push down.
b) Simply lift the leg rest to put it back to the starting position.
5