Table of Contents
Advertisement
c) For eliminate squeaking on you CYBEX buggy take only WD 40 and follow the
mentioned pictures below. Do not use any other kind of lubricant! Insert always a cloth
or a carton in order to leave no oil stains. Please pay special attention to not apply the
lubricant on any other part of the stroller (fabrics, tubes, etc.).
II.-II applying of the lubricant
a) Rear Wheel - Spray from the rear side of the buggy in the space between the rim and
the housing on both sides. Let the lubricant get into the system for approx. 10 seconds,
and then turn the wheels.
b) Front Wheel - Spray in the space between the rim and the housing on both sides. Let
the lubricant get into the system for approx. 10 seconds, and then turn the wheels.
Should this not avoid the squeaking, please remove the rim cap and apply the spray on
the axle.
c) Suspension - Apply some lubricant between the suspension slider and the housings.
DISPoSaL
When you are done using your CYBEX ONYX/TOPAZ a proper disposal is important.
Garbage disposal can be different in every country. Please contact your local waste
management company to make sure you are taking the right steps to dispose of the CYBEX
ONYX/TOPAZ. Always follow the disposal regulations of your country.
III. INSTRUCTIoNS FoR USE
ImPoRTaNT: REaD THESE INSTRUCTIoNS CaREFULLY
BEFoRE USE aND KEEP THEm FoR FUTURE REFERENCE.
YoUR CHILDREN'S SaFETY maY BE aFFECTED IF YoU Do
NoT FoLLoW THESE INSTRUCTIoNS.
oNYX/ToPaz aSSEmBLY INSTRUCTIoN
Delivery Status
1. oPENING THE STRoLLER
a) Release the folding lock lever.
b) Open the stroller.
c) Push the pedal button down until the locking system is engaged.
2. aSSEmBLING THE HaNDLES
aTTENTIoN: THE PINS oN BoTH SIDES mUST BE ENGaGED.
3. aSSEmBLING THE FRoNT WHEELS
– Fit the front wheels to the end of the frame until they engage with a "click".
4. aSSEmBLING THE REaR WHEELS
aTTENTIoN: THE WHEEL SYSTEm WITH THE BRaKE PEDaL
mUST BE FITTED To THE RIGHT SIDE oF THE BUGGY
4
(VIEWED FRom BEHIND THE BUGGY).
aTTENTIoN: THE PINS oN BoTH SIDES mUST BE ENGaGED.
ENSURE THE BoWDEN CaBLE IS INSERTED INTo THE CLIPS
oN BoTH SIDES.
5. aTTaCHING THE BUmPER BaR
a) Slide in latches on left and right side into gadgets sewn into the seat fabric.
b) Press the buttons on left and right side of the bumper bar to take it off.
6. FoLDING THE STRoLLER
Remove all contents from the basket. Close the canopy. Remove the bumperbar.
a Lift the central lever located at the back of the shopping basket.
b) Push down the lock lever (extended bar on the right side of the locking system).
c) Grip handles and push forward on the stroller to fold it.
d) Press folded stroller until the fold lock is engaged. Its recommended to fasten the
harness before folding the stroller.
7. oPENING THE STRoLLER
a) Release the fold lock lever.
b) Open the stroller
c) Push the pedal button down until the locking system is engaged.
WarNING
ENSURE THaT aLL LoCKING DEVICES aRE ENGaGED
BEFoRE USE.
8. USING THE BRaKES
a) Engage Brake
b) Release Brake
9. aUTomaTIC FRoNT WHEEL SWIVEL LoCKS – LoCK – UNLoCK
a) Push the Front Swivel Lock Lever until it "clicks". It can be activated in any wheel
positions. The swivel Lock will engage automatically when it reaches the right position.
b) Lift the Front Swivel Lock Lever up again to release the Swivel Lock.
10. EXTENDaBLE CaNoPY
– Attach the canopy adaptor on to the inside of the frame tubes of the buggy.
– To remove the canopy reverse procedure.
– Extend the canopy and place canopy rear flap behind the seat.
– Lie-flat position: Put the rear flap over the seat's back rest and fixate it with the two
velcros underneath.
The canopy is adjustable to various positions. The Canopy has a height adjustment and a
Advertisement
Table of Contents
