Desa NY100 Safety Information And Installation Manual page 18

OpERATING HEATER
Continued
If room temperature is higher than 99° F, the
word HI will display on the room temperature
window frame. If room temperature is lower
than 32° F, the word LO will display on the
room temperature window frame.
Operational Note: To conserve battery power,
changes in room temperature are automatically
updated every 2 minutes to remote control.
Mode button will operate ON-THERMO-OFF
in series that will cycle from ON to THERMO
to OFF.
Setting Programs
In Program Mode, remote control will allow
heater to automatically turn on and off at spe-
cific times. Two on and off segments per day
may be set, or settings previously programmed
at the factory may be used. On and off times
are available in 15 minute increments.
To Activate the Program Mode
A short push (press and release) on TIME/
PROGRAM button will activate or deactivate
program mode.
A long push (press and hold for more than
5 seconds) on TIME/PROGRAM button will
enter into setting of program.
When the program mode is activated, the P-1
and P-2 icons and the word OFF will display
on the screen. This means that unit turns off
manual mode and enters into program mode.
The unit will automatically check if current time
is within pre-programmed ON time.
If current time is within program on time, unit
will enter into thermo mode automatically
and the word THERMO and set temperature
digit(s) will display on screen.
When room temperature is below set tem-
perature, unit will turn on and the word ON
will replace the word OFF on the screen. The
flame icon will also show on the screen. Unit
will continue to operate in thermo mode until
program off time is reached. When program
off time is reached, unit will turn off and stay
off until next program on time is reached or
until user turns program mode off and turns
unit on in manual or thermo mode.
If current time is not within program on time,
unit will stay off until pre-programmed turn
on time is reached. Pre-programmed time
(P-1 and P-2 icons) will continue to display
on screen indicating that unit is in program
mode until set time is reached.
18
When program mode is deactivated, P-1 and
P-2 icons and set temperature digit(s) will
disappear from screen.
Factory Settings
The program function is preset at the follow-
ing on and off times. These times will apply
to every day of the week.
Program 1 (P1): Turn on at 7:00 AM. Turn off
at 9:00 AM.
Program 2 (P2): Turn on at 5:00 PM. Turn off
at 8:00 PM.
Setting a New Program
To change Program from the factory settings
to new settings:
1. Press and hold TIME/PROGRAM button
for more than 5 seconds to enter Set
Program Mode.
2. P1 ON will flash. Push UP or DOWN but-
ton until desired on time for Program 1 is
reached. Press SET button.
3. P1 OFF will flash. Push UP or DOWN
button until desired off time for Program
1 is reached. Press SET button.
4. P2 ON will flash. Push UP or DOWN but-
ton until desired on time for Program 2 is
reached. Press SET button.
5. P2 OFF will flash. Push UP or DOWN
button until desired off time for Program
2 is reached. Press SET button.
The new program is now set and unit is in
program mode. To take unit out of program
mode, press and release TIME/PROGRAM
button.
Note: In set program mode, set times will flash
for 15 seconds. If the UP, DOWN or SET but-
ton is not pressed within 15 seconds, system
will automatically complete set up process and
LCD Screen will revert to normal readouts.
The first factory set temperature is at 45° F.
Appliance will not turn on if room is not below
the set temperature. If set temperature is at
70° F, appliance will come on only if room
temperature is below 70° F.
Low Battery Indicator
A low BATTERY ICON on left side of LCD
screen will appear when battery power has
dropped significantly. At this time, approxi-
mately two weeks of battery power remains
until remote control may experience partial or
complete loss of functions.
www.desatech.com 118620-01E