Page 1
INSTALLATION INSTRUCTIONS FOR PART 98-9306 3 SERIES 2006-2010 (Not for models with Factory Navigation) 98-9306 (Used For Heated Seat Models When Using The 95-9306B) KIT FEATURES • Relocates Heated Seat Switches KIT COMPONENTS • A) Pocket • B) Heated Seat Switch Trim Panel • C) Extension Harness •...
Page 2
INSTALLATION INSTRUCTIONS FOR PART 98-9306 TABLE OF CONTENTS DASH DISASSEMBLY •BMW 3 Series 2006-10 ....1-2 KIT ASSEMBLY •BMW 3 Series 2006-10 ....3-4 CAUTION: Metra recommends disconnecting the negative battery terminal before beginning any installation.
Page 3
98-9306 DASH DISASSEMBLY BMW 3 SERIES 2006-2010 Carefully unclip and remove the shifter trim panel. (Fig. A) Remove (4) Torx screws securing the pocket or ash tray assembly to the shifter trim panel. (Fig. B) Unclip and remove the heated seat switch assembly from the climate control panel.
Page 4
98-9306 DASH DISASSEMBLY BMW 3 SERIES 2006-2010 Remove the circuit board and unplug the factory harness. (Fig. D) Continue to Kit Assembly...
Page 5
98-9306 KIT ASSEMBLY BMW 3 SERIES 2006-2010 Plug the extension harness onto the circuit board. Then reassemble the heated seat switch assembly. (Fig. A) Continue to PG.4...
Page 6
Clip the heated seat switch trim panel into the pocket. (Fig. B) Clip the heated seat switch assembly into the pocket/trim panel assembly. (Fig. B) Reattach the 98-9306 pocket assembly to the shifter trim panel using the factory hardware. Route the extension harness through the left side of the dash cavity and plug...
INSTRUCCIONES PARA LA INSTALACIÓN DE PARTE 98-9306 (No apto para modelos con navegación de fábrica) 98-9306 (Empleado para los modelos de asiento con calefacción cuando se utiliza el 95-9306B) CARACTERÍSTICAS DEL KIT • Reubica interruptores del asiento con calefacción COMPONENTES DEL KIT •...
Page 8
INSTRUCCIONES PARA LA INSTALACIÓN DE PARTE 98-9306 PÁGINA DE ÍNDICE DESMONTAJE DEL TABLERO •BMW Serie 3 2006-2010 ....1-2 MONTAJE DEL KIT •BMW Serie 3 2006-2010 ....3-4 Precaución: Metra recomienda desconectar el terminal negativo de la...
Page 9
98-9306 DESMONTAJE DEL TABLERO BMW SERIE 3 2006-2010 Desenganche y retire con cuidado el panel de terminación de la palanca de velocidades. (FIg. A) Retire (4) tornillos Torx que sujetan el conjunto del bolsillo o del cenicero en el panel de terminación de la palanca de velocidades.
Page 10
98-9306 DESMONTAJE DEL TABLERO BMW SERIE 3 2006-2010 Retire el tablero de circuitos y desenchufe el arnés de fábrica. (Fig. D) Continuar con la Asamblea Kit...
Page 11
98-9306 MONTAJE DEL KIT BMW SERIE 3 2006-2010 Enchufe el arnés de extensión al tablero de circuitos. Luego vuelva a montar el conjunto del interruptor del asiento con calefacción. (Fig. A) Continuar con la PG.4 ...
Page 12
Enganche el conjunto del interruptor del asiento con calefacción dentro del conjunto del bolsillo/panel de terminación. (Fig. B) Vuelva a colocar el conjunto del bolsillo 98-9306 en el panel de terminación de la palanca de velocidades usando los elementos de fábrica.