Hellenbrand E3 Owner's Manual page 12

ITEM NO.
ORDER NO.
1 109380
2-6 101610
2 102096
3 101262
4 109379
5 101746
6 101459
Not Shown 102653
After completing any valve maintenance involving the drive assembly or the
drive cap assembly and pistons, press and hold NEXT and REGEN buttons
for 3 seconds or unplug power source jack from the printed circuit board (black
wire) and plug back in. This resets the electronics and establishes the service
piston position. The display should flash all wording, then flash the software
version (ex: 154) and then reset the valve to the service position.
DRIVE CAP ASSEMBLY, DOWNFLOW PISTON, REGENERANT PISTON
ITEM NO.
ORDER NO.
1 102548
2 101613
3 102167
4a 102292
4b 102297
5 102296
6 102192
7 102165
Not Shown 102892
*102292 is labeled with DN and 102297 is labeled with UP.
Note: The regenerant piston is not used in backwash only applications.
**Standard Option.
Do not use vaseline, oils, other hydrocarbon lubricants or spray silicone anywhere. A silicon lubricant may be used on black o-rings but is not necessary. Avoid any
type of lubricants, including silicone, on red or clear lip seals.
After completing any valve maintenance involving the drive assembly or the drive cap assembly and pistons, press and hold NEXT and REGEN buttons for 3 seconds
or unplug power source jack from the printed circuit board (black wire) and plug back in. This resets the electronics and establishes the service piston position. The
display should flash all wording, then flash the software version (ex: 154) and then reset the valve to the service position.
12
FRONT COVER AND DRIVE ASSEMBLY
DESCRIPTION
Black Cover Assy w/ Label
Drive Assy.
Motor
Drive Bracket & Spring Clip
PC Board
Drive Gear 12x36
Drive Gear Cover
Transformer 110V-12V
AND SPACER STACK ASSEMBLY
DESCRIPTION
Spacer Stack Assy
Drive Cap Assy.
O-Ring 228
Piston Downflow Assy.
Piston Upflow Assy.
Regenerant Piston
O-ring 337-tank
O-ring distributor tube
Service Wrench

4 V3108-09BOARD WS1 PC Board with Battery REPLACE
5
6
Not Shown
Not Shown
* Drawing number parts 2 through 6 may be purchased as a complete assembly, part V3002.
QTY.
1 When replacing the battery, align
positives and push down to fully seat.
*
1
1
1
3

1
1

QTY.
1
1
1
1**
1
1
1
1
1
E
D

V3110 WS1 Drive Gear 12x36
V3109 WS1 Drive Gear Cover
V3002 WS1 Drive ASY
V3186 WS1 AC Adapter 110V-12V
V3186 WS1 AC ADAPTER 110V-12V
V3186EU WS1 AC ADAPTER 220-240V-12V EU
V3186UK WS1 AC ADAPTER 220-240V-12V UK
V3186-01 WS1 AC ADAPTER CORD ONLY
Correct
Battery
Orientation
Battery Fully Seated


DRAWN ENG APPR. DATE
DIMENSIONS ARE IN INCHES
REVISIONS TOLERANCE: X" +/- 2"
NO. DATE BY COMMENTS PROPRIETARY AND CONFIDENTIAL:
THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF
HELLENBRAND INC. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSION OF HELLENBRAND INC.
IS PROHIBITED.


7
1
3
1
*
1
1
Battery replacement is
3 volt lithium coin cell
type 2032.




DWG DESCRIPTION:
Hellenbrand

DWG. NO. REV.

Figure 13

Figure 14
