Page 1 Before driving Introduction Instrumentation Controls and features Seating and safety restraints Starting and driving Starting Driving Roadside emergencies Servicing Maintenance and care Capacities and specifications Customer assistance Reporting safety defects Index All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company.
Page 2: Introduction
Introduction ICONS Indicates a safety alert. Read the following section on Warnings. Indicates vehicle information related to recycling and other environmental concerns will follow. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment.
Page 3 INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. SPECIAL NOTICES Notice to owners of utility type vehicles Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car.
Page 4 Instrumentation Headlamp control (pg. 20) Turn signal and Instrument panel wiper/washer control dimmer switch (pg. 85) (pg. 21) Tilt steering wheel lever (pg. 85) Instrument cluster (pg. 6) 50 60 70 o o o UNLEADED FUEL ONLY 0 0 0 0 0 0 RPM x 1000 km/h Driver side air bag...
Page 5 Electronic sound system (pg. 34) Gearshift (includes overdrive button) (pg. 149) VOL – PUSH ON FM BASS TREB SEEK SCAN TUNE DISCS Climate controls (pg. 87) Instrumentation Rear window defroster control (pg. 31) Rear window/washer control (pg. 86) R. WIPE FM 1 BAL FADE AUTO...
Page 6 Instrumentation WARNING LIGHTS AND CHIMES CHECK GAGE RPMx1000 CHECK ENGINE FUEL RESET BRAKE Check engine Your vehicle is equipped with a computer that monitors the engine’s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II).
Page 7: Instrumentation
3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel and/or properly installing and securely tightening the gas cap. After three driving cycles without these or any other temporary malfunctions present, the Check Engine light should turn off.
Page 8 Instrumentation Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Brake system warning Momentarily illuminates when the ignition is turned to the ON position and the engine is off.
Page 9 Instrumentation High beams Illuminates when the high beam headlamps are turned on. Anti-theft system (if equipped) Refer to SecuriLock passive anti-theft system in the Controls THEFT and features chapter. Charging system Illuminates when the ignition is turned to the ON position and the engine is off.
Page 10 Instrumentation Four wheel drive high (if equipped) This light momentarily illuminates when the ignition is turned to ON. Illuminates when four-wheel drive high is engaged. If the light continues to flash have the system serviced. Door ajar Illuminates when the ignition is in the ON or START position and any door is open.
Page 11 pressed, the brake is applied or the ignition is turned to the OFF position. Safety belt warning chime Chimes to remind you to fasten your safety belts. For information on the safety belt warning chime, refer to the Seating and safety restraints chapter. Supplemental restraint system (SRS) warning chime For information on the SRS warning chime, refer to the Seating and safety restraints chapter.
Page 12 Instrumentation Speedometer Indicates the current vehicle speed. Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating.
Page 13 Odometer Registers the total kilometers (miles) of the vehicle. Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control. Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
Page 14 Instrumentation Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated), have the vehicle’s electrical system checked as soon as possible. Engine oil pressure gauge This shows the engine oil pressure in the system.
Page 15 Instrumentation Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled.
Page 16 Instrumentation Selectable features English/metric display Press to toggle the message center display between metric or English units. Fuel range Press once to display the approximate kilometers (miles) left to drive before the fuel tank is empty. Press again to display the distance driven since this function was last manually reset.
Page 17 Fuel economy Press to display your vehicle’s average fuel economy in liters/100 km or (miles/gallons). Reset Press the reset control to reset the current feature being displayed. Warnings, distance driven, average fuel economy, fuel used and personalized oil reset percentage are the only features that respond to reset.
Page 18 Instrumentation The engine oil life left has two phases. The first display will indicate the oil change status (OK, SOON, REQUIRED). The second display will indicate the percentage of oil life remaining. The display OIL TEMP SIGNAL ERROR indicates a problem with the system. Following this display, contact your dealer or qualified service technician for system maintenance.
Page 19 Instrumentation OIL LIFE RESET TO 100%. (If you have established a personalized oil reset percentage, the display will show that percentage instead of 100%.) This reset procedure should be performed only after an oil change to ensure accurate oil life indications. Your personalized oil reset percentage allows you to establish a smaller oil change interval than the manufacturer’s recommended interval.
Page 20: Controls And Features
Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. Foglamp control (if equipped) Turn on the low-beam headlamps and press the foglamp control to activate the foglamps.
Page 21 Flash to pass Pull toward you to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. Rotate up to brighten. Rotate down to dim. Rotate to full down position to turn off.
Page 22: Controls And Features
Controls and features Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle. The air conditioning compressor will operate in all modes except .
Page 23 Controls and features (Panel and floor)-Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot and full cold positions, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers.
Page 24 Controls and features Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield under the hood). If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
Page 25 Controls and features Turning the EATC off Press OFF. AUTOMATIC FLR • DEF Automatic operation Press AUTOMATIC and select the desired temperature. The selected temperature and the word AUTO will appear in the display window. The EATC system will either heat or cool to achieve the selected temperature.
Page 26 Controls and features To control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer) buttons. For continuous maximum cooling, push the blue button until 16°C (60°F) is shown in the display window. The EATC will continue maximum cooling (disregarding the displayed temperature) until a warmer temperature is selected by pressing the red button.
Page 27 Rotate the thumbwheel up for higher fan speed or down for lower fan speed. Press the steering wheel fan speed control up for higher fan speed or down for lower fan speed. The display will show to indicate manual fan operation. To return to automatic fan operation, press AUTOMATIC.
Page 28 Controls and features PNL FLR-Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode. The air will be heated or cooled based on the temperature selection. For added customer comfort, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers.
Page 29 The EATC display window will indicate REAR FAN OFF. The rear console fan will remain off until REAR FAN OFF is pressed again. Operating tips In humid weather, select DEF your windshield from fogging. After a few minutes, select any desired position.
Page 30 Controls and features Rear console climate controls (if equipped) Depending on the equipment - VOLUME + MODE package of your vehicle, the rear console may be equipped with rear console audio/climate controls. SEEK MEMORY The instrument panel climate controls must be on in order for the rear console climate controls to work.
Page 31 Controls and features Select for air to flow through these vents: – VOLUME BAND SEEK MEMORY REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog.
Page 32 Controls and features 4WD CONTROL (IF EQUIPPED) This control operates the 4WD. Refer to the Driving chapter for more information. REVERSE SENSING SYSTEM (IF EQUIPPED) The reverse sensing system (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when the reverse gear is selected. The RSS will assist the driver in detecting certain objects while the vehicle slowly moves in reverse at speeds less than 8 km/h (3 mph).
Page 33 Controls and features The reverse sensing system detects obstacles within approximately 1.8 meters (5.9 ft.) of the rear bumper with a decreased coverage area at the outer corners of the bumper. As you move closer to the obstacle, the rate of the tone increases. When the distance to the obstacle is less than 20.0 cm (8 in.), the tone will sound continuously.
Page 34 Controls and features To help avoid personal injury, please read and understand the limitations on the reverse sensing system described above. Reverse sensing is only an assist for some (generally large and fixed) objects. It is the drivers responsibility for ensuring that their path is clear when operating the vehicle.
Page 35 Controls and features Volume/power control Press the control to turn the audio VOL - PUSH ON system on or off. Turn the control to raise or lower volume. VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
Page 36 Controls and features Tune adjust The tune control works in radio mode. Tune adjust in radio mode Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly.
Page 37 Controls and features Setting memory preset stations 1. Select the frequency band with the AM or the FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
Page 38 Controls and features Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Tape select To enter tape mode while in radio mode, press the TAPE AMS control.
Page 39 To activate the feature, momentarily depress the TAPE AMS button. Then, press either REW (for the beginning of the current selection) or FF (to advance to the next selection). The tape deck stops and returns to play mode when the AMS circuit senses a blank section on the tape. In order to ensure proper operation of the AMS feature, the tape MUST have a blank section of at least 4 seconds duration between programs.
Page 40 Controls and features Press the control to activate (and deactivate) Dolby noise reduction. The noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Setting the clock To set the hour, press and hold the CLK control and press: to decrease hours and to increase hours.
Page 41 to decrease minutes and to increase minutes. AM/FM Stereo / Single CD Radio VOL - PUSH ON BASS TREB SEEK TUNE Volume/power control Press the control to turn the audio system on or off. Controls and features SEEK TUNE FADE DISC VOL - PUSH ON SEEK...
Page 42 Controls and features Turn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio and CD modes.
Page 43 Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. Seek function The seek function control works in radio or CD mode. Seek function in radio mode Press to find the next listenable station down the...
Page 44 Controls and features Radio station memory preset The radio is equipped with four or six station memory preset controls. These controls can be used to select up to four or six preset AM stations and eight or twelve FM stations (four to six in FM1 and four to six in FM2).
Page 45 Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. CD select To begin CD play (if CD[s] are loaded), press the CD control. The first track of the disc will begin playing.
Page 46 Controls and features Setting the clock To set the hour, press and hold the CLK control and press: to decrease hours and to increase hours. To set the minute, press and hold the CLK control and press: to decrease minutes and to increase minutes.
Page 47 Premium AM/FM Stereo/Cassette/Single CD/Premium Sound VOL - PUSH ON FM 1 DOLBY B NR SEEK TUNE SCAN BASS TREB SIDE 1-2 Volume/power control Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the tape/CD select control.
Page 48 Controls and features If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD modes.
Page 49 Tune adjust for CD changer (if equipped) Press to select the previous disc in the CD changer. (Play will begin on the first track of the disc unless the CD changer is in shuffle mode. Refer to Shuffle feature for more information. Hold the control to continue reversing through the remaining discs.
Page 50 Controls and features Seek function for CD or CD changer (if equipped) Press to seek to the previous track of the current disc. If a selection has been playing for three seconds or more and you press , the CD changer will replay that selection from the beginning.
Page 51 Controls and features Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. SIDE 1-2 COMP SHUFFLE 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
Page 52 Controls and features To deactivate autoset and return to your audio system’s manually set memory stations, press the AUTO control again. Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control then press: to decrease the bass output to increase the bass output.
Page 53 to shift sound to the left and to shift sound to the right. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control then press: to shift the sound to the front and to shift the sound to the rear.
Page 54 Controls and features Rewind The rewind control works in tape and CD modes. In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. In CD mode, pressing the REW control rewinds the CD within the current track.
Page 55 Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Compression adjust Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust.
Page 56 Controls and features To set the minute, press and hold the CLK control and press TUNE: to decrease minutes and to increase minutes. If your vehicle has a separate clock module, (other than the digital radio display), the CLK button will not function in the above manner.
Page 57 Mute mode Press the control to mute the playing media. Press the control again to return to the playing media. Rear seat controls (if equipped) The Personal Audio System, a feature of the optional Premium AM/FM Stereo/Cassette/Single CD/Premium Sound and the MACH Audio System with AM/FM Stereo/Cassette/Single CD, allows front and middle seat passengers to...
Page 58 Controls and features To activate the Personal Audio System, press the speaker/headphone control. Press the MODE control to change audio sources (for headphone mode only). Use the SEEK, VOLUME and MEMORY controls to make adjustments to the playing media. Adjusting the volume Press the + control to increase volume.
Page 59 Turning the speakers on and off Press to turn all speakers on or off. Using headphones Plug a 3.5 mm headphone (not included) into the speaker on/off control to operate the headphones. The rear speakers will cut out once the speaker on/off control is pressed. The front speaker will remain playing for the front passengers.
Page 60 Controls and features Memory preset control Push the MEMORY control successively to allow rear seat passengers to scroll through the 6 memory presets in AM, FM1 or FM2. Push the MEMORY control in CD changer mode (if equipped) to advance to the next disc. Seek function In radio mode, press to find...
Page 61 MACH Audio System with AM/FM Stereo/Cassette/Single CD VOL - PUSH ON DOLBY B NR SEEK TUNE SCAN BASS TREB SIDE 1-2 Your audio system is equipped with selective lighting, a unique lighting strategy. This lighting feature is operable when the headlamps are illuminated.
Page 62 Controls and features Turn control to raise or lower VOL - PUSH ON volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Page 63 Tune adjust in radio mode Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. Press to move to the next frequency up the band (whether or not a listenable station is located there).
Page 64 Controls and features Seek function in tape mode Press to listen to the previous selection on the tape. Press to listen to the next selection on the tape. Seek function for CD changer (if equipped) Press to seek to the previous track of the current disc.
Page 65 Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Setting memory preset stations 1.
Page 66 Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control then press: to decrease bass output and to increase bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output.
Page 67 Press the BAL control then press: to shift sound to the left and to shift sound to the right. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control then press: to shift sound to the front to shift sound to the rear.
Page 68 Controls and features Rewind The rewind control works in tape and CD modes. In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. In CD mode, pressing the REW control for less than three seconds results in slow rewind.
Page 69 Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Compression adjust Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust.
Page 70 Controls and features To set the minute, press the clock/RDS control until SELECT MIN is displayed and press: to decrease minutes and to increase minutes. Radio Data System (RDS) feature This feature allows your audio system to receive text information from RDS-equipped FM radio stations.
Page 71 RDS traffic announcement Press the RDS control until TRAFFIC is displayed. Use the SELECT control to select ON or OFF. With the feature ON, use the SEEK or SCAN control to find a radio station broadcasting a traffic report (if it is broadcasting RDS data).
Page 72 Controls and features Use the SEL control to select the program type. With the feature on, use the SEEK or AUTOSET or SCAN control to find the desired program type from the following selections: Classic Country Info Jazz/R&B Religious Rock Soft Top 40 RDS show...
Page 73 Mute mode Press the control to mute the playing media. Press the control again to return to the playing media. Rear seat controls (if equipped) The Personal Audio System, a feature of the optional Premium AM/FM Stereo/Cassette/Single CD/Premium Sound and the MACH Audio System with AM/FM Stereo/Cassette/Single CD, allows front and middle seat passengers to...
Page 74 Controls and features Adjusting the volume Press the + control to increase volume. Press the - control to decrease volume. From the rear seat controls, volume control can be set no higher than the current radio setting unless the speakers are turned off. Refer to Turning speakers on and off.
Page 75 The rear speakers will cut out once the speaker on/off control is pressed. The front speaker will remain playing for the front passengers. Press the control again to deactivate the headphones. Mode select Push the MODE control to toggle between AM, FM1, FM2, tape, CD or CD changer (if equipped).
Page 76 Controls and features In CD mode (if equipped), use the SEEK function to access the next or previous selection. CD changer (if equipped) The CD changer is located in one of the following locations: in the trunk in the center console under the driver’s seat 1.
Page 77 If you pull too hard on the disc holder, the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A). 5. Line up the CD with the groove of the disc holder.
Page 78 Controls and features The CD magazine may be inserted or ejected with the radio power off. ONLY use the magazine supplied with the CD changer, other types will damage the unit. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty.
Page 79 Cleaning cassette player (if equipped) Clean the tape player head with a cassette cleaning cartridge after ten to twelve hours of play in order to maintain the best sound and operation. Cassette and cassette player care Use only cassettes that are 90 minutes long or less. Do not expose tapes to direct sunlight, high humidity, extreme heat or extreme cold.
Page 80 Controls and features Station overload. Weak signals are sometimes captured by stronger signals when you pass a broadcast tower. A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed. The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo.
Page 81 SPEED CONTROL To turn speed control on Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. Do not shift the gearshift lever into N (Neutral) with the speed control on.
Page 82 Controls and features To set a speed Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed.
Page 83 You can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed. To set a lower set speed Press and hold CST/COAST. Release the control when the desired speed is reached or Press and release CST/COAST.
Page 84 Controls and features Pressing OFF will erase the previously programmed set speed. To return to a previously set speed Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on when either the SET ACC/SET ACCEL or RES/RSM/RESUME controls are pressed.
Page 85 Controls and features TILT STEERING WHEEL Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving.
Page 86 Controls and features Push the control on the end of the stalk to activate washer. Push and hold for a longer wash cycle. The washer will automatically shut off after ten seconds of continuous use. Speed dependent wipers When the windshield wiper control is set on the intermittent settings, speed-sensitive front wipers automatically adjust as the vehicle’s speed increases.
Page 87 Radio control features Press BAND/MODE to select AM, FM1, FM2, TAPE or CD (if equipped). In Radio mode: Press MEM/NEXT to select a preset station from memory. In Tape mode: Press MEM/NEXT to listen to the next selection on the tape. In CD mode: Press MEM/NEXT to listen to the next track on the disc.
Page 88 Controls and features Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open. Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: Remove the storage clip from the door.
Page 89 Press the GARAGE control to activate the transmitter. Moon roof (if equipped) You can move the moon roof back to open the glass panel or tilt up to ventilate the vehicle. To open the moon roof: The moon roof is equipped with an automatic, one-touch, express opening feature.
Page 90 Controls and features Do not let children play with the moon roof. They may seriously hurt themselves. Electronic compass/temperature display (if equipped) Outside air temperature The outside temperature display is contained in the overhead console. The temperature display can be turned off and on by pressing the MODE control on the overhead console.
Page 91 Controls and features Compass zone adjustment 1. Determine which magnetic zone you are in by referring to the zone map. 2. Press and hold the MODE control until VAR appears in the display, then release. The display should show the current zone number. 3.
Page 92 Controls and features Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines: Press and hold the MODE control until CAL appears in the display (approximately eight seconds) and release. Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles until CAL indicator turns off in about 2–3 complete circles.
Page 93 Programming 1. Prepare for programming the HomeLink Universal Transceiver by erasing the three factory default codes by holding down the two outside buttons until the red light begins to flash after 20 seconds. Release both buttons. 2. Hold the end of your hand-held transmitter 5–14 cm (2–5 inches) away from the HomeLink Universal Transceiver surface (located on your visor) while keeping the red light in view.
Page 94 Controls and features Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting after two seconds which may not be long enough to program the HomeLink Universal Transceiver. To program your hand-held transmitters: continue to hold the button on the HomeLink Universal Transceiver.
Page 95 After completing the “Programming” functions, follow these steps to train a garage door opener with the rolling code feature: 1. Locate the training button on the garage door motor head unit. Refer to the garage door opener manual or call 1–800–355–3515 or on the Internet at HomeLink.jci.com.
Page 96 Controls and features Reprogramming a single HomeLink button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink button. Do NOT release until step 4 has been completed. 2.
Page 97 To play a message: 1. Press and release the PLAY button to play the message. 2. Press and hold the PLAY button to hear all the messages in consecutive order starting with the most recent. 3. If the PLAY button is pressed while a message is being listened to, TravelNote will skip to the beginning of the next message.
Page 98 Controls and features Setting autolamp 1. Make sure the headlamp control is in the OFF position. Leaving the headlamp control on will override the autolamp. 2. Turn the ignition to the ON position or start the vehicle. 3. Slide the delay control all the way to the left.
Page 99 POWER WINDOWS Press and hold the rocker switches to open and close windows. Press the top portion of the rocker switch to close. Press the bottom portion of the rocker switch to open. One touch down Press AUTO completely down and release quickly.
Page 100 Controls and features Window lock The window lock feature allows only the driver to operate the power windows. WINDOW LOCK To lock out all the window controls except for the driver’s press the left side of the control. Press the right side to restore the window controls. POWER DOOR LOCKS Press U to unlock all doors and L to lock all doors.
Page 101 POWER SIDE VIEW MIRRORS To adjust your mirrors: 1. Select to adjust the left mirror or 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist...
Page 102 Controls and features ashcup compact disc changer (if equipped) removable utility bag (if equipped) Use only soft cups in the cupholder. Hard objects can injure you in a collision. Auxiliary power point The power point is an additional power source for electrical accessories.
Page 103 CENTER ARMREST/REAR CUPHOLDER Do not attempt to raise the console armrest when the rear cupholder is in use. If you find resistance when raising the armrest, make sure the cupholder is fully closed or else damage may occur to the armrest. POSITIVE RETENTION FLOOR MAT To install floor mats: 1.
Page 104 Controls and features The liftgate door and window should be closed before driving your vehicle. If not, possible damage may occur to the liftgate door lift cylinders and attaching hardware. Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle.
Page 105 1. Remove the shade from the vehicle and extend it with the smooth grain facing you. 2. Wrap the vinyl around the roller tube twice. Tuck the edges of the vinyl inside the end cap with each wrap. 3. Fold the edges of the vinyl towards the center, making sure that the edges clear the end cap slots.
Page 106 Controls and features Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will illuminate. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors. To confirm all doors are closed and locked, press the control a second time within five seconds.
Page 107 Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Memory seat feature (if equipped) The remote entry system can also control the memory seat feature. Press the control once to unlock the driver’s door and move the memory seat feature to the corresponding memory position, just as if you had...
Page 108 Controls and features The memory feature will continue to work from the door control even when deactivated at the remote entry module. Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
Page 109 Replacing lost transmitters Take all your vehicle’s transmitters to your dealer if service is required. If you purchase additional transmitters (up to four may be programmed), perform the following procedure: To reprogram the transmitters yourself, place the key in the ignition and turn from OFF to ON eight times in rapid succession (within 10 seconds) ending in ON.
Page 110 Controls and features The autolock feature repeats when: any door is opened and then closed the brake pedal is released Deactivating autolock Before following the activation or deactivation procedures, make sure that the ignition is OFF and all vehicle doors and liftgate window are closed.
Page 111 If autolock/relock has been changed, the horn will chirp to confirm procedure is complete. Keyless entry system (if equipped) With the keyless entry keypad, you can: lock or unlock the vehicle doors without using the key activate/deactivate the autolock feature See also Remote entry system in this chapter for more information.
Page 112 Controls and features If you wish to erase your personal code, use the following instructions: Erasing personal code 1. Enter the factory-set code. 2. Press 1/2 within five seconds of step 1. 3. Press the 7/8 and 9/0 controls at the same time within five seconds of step two.
Page 113 SECURILOCK PASSIVE ANTI-THEFT SYSTEM The SecuriLock passive anti-theft system provides an advanced level of vehicle theft protection. Your vehicle’s engine can only be started with the two special SecuriLock electronically coded keys provided with your vehicle. Each time you start your vehicle, the SecuriLock read by the SecuriLock passive anti-theft system.
Page 114 Controls and features Theft indicator The theft indicator on the instrument cluster will operate as follows: When the ignition is OFF, the theft indicator will flash briefly every 2 seconds to indicate the SecuriLock vehicle. When the ignition is turned to RUN or START, the theft indicator will light for 3 seconds and then go out.
Page 115 Controls and features Procedure to program spare SecuriLock keys to your vehicle New SecuriLock keys must have the correct mechanical key cut for your vehicle. Conventional (non-SecuriLock ) keys cannot be programmed to your vehicle. You will need to have two previously programmed SecuriLock keys and the new unprogrammed SecuriLock key readily accessible for the...
Page 116: Seating And Safety Restraints
Seating and safety restraints SEATING Using the manual lumbar support Turn the lumbar support control toward the front of vehicle to increase firmness. Turn the lumbar support control toward the rear of vehicle to increase softness. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving.
Page 117 Seating and safety restraints Press to raise or lower the front portion of the seat cushion. Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down.
Page 118 Seating and safety restraints REAR SEATS Folding rear seats (if equipped) If your vehicle is equipped with a built-in child seat, the seatback cannot be folded down unless the built-in child seat is fully stowed. 1. Press the lower release control downward to unlatch the seatback.
Page 119 Seating and safety restraints To return the seat to the upright position: Press downward on the upper corner of the seatback and hold. Pull the release handle upward to unlatch the seat. Rotate the seatback upward until the seatback latches in the upright position.
Page 120 Seating and safety restraints All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag SRS is provided. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Page 121 Seating and safety restraints 2. To unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front and rear seat passenger outboard safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free...
Page 122 Seating and safety restraints How to use the automatic locking mode Buckle the combination lap and shoulder belt. Grasp the shoulder portion and pull downward until the entire belt is extracted. Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Page 123 Seating and safety restraints This seat belt system has a retractor assembly that is designed to pay out webbing in a controlled manner. This feature is designed to help reduce the belt force acting on the occupant’s chest. After any vehicle collision, the seat belt system at all outboard seating positions (except driver, which has no “automatic locking retractor”...
Page 124 Seating and safety restraints Safety belt extension assembly If the safety belt assembly is too short, even when fully extended, 20 cm (8 inches) can be added to the safety belt assembly by adding a safety belt extension assembly (part number 611C22). Safety belt extension assemblies can be obtained from your dealer at no cost.
Page 125 Seating and safety restraints Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, wears or cuts, replacing if necessary. All safety belt assemblies, including retractors, buckles, front seat belt buckle assemblies (slide bar)(if equipped), shoulder belt height adjusters (if equipped), child safety seat tether bracket assemblies (if equipped),...
Page 126 Seating and safety restraints Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag...
Page 127 Seating and safety restraints Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Children and air bags For additional important safety information, read all information on safety restraints in this guide.
Page 128 Seating and safety restraints near-frontal collisions, not rollover, side-impact, or rear-impacts. The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking...
Page 129 Do not attempt to service, repair, or modify the air bag Supplemental Restraint System, its fuses or the seat cover on a seat containing an air bag. See your Ford or Lincoln Mercury dealer.
Page 130 Seating and safety restraints All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided. How does the side air bag system work? The side air bag system consists of the following: An inflatable nylon bag (air bag) with a gas generator concealed...
Page 131 Seating and safety restraints near-frontal collisions, unless the collision causes sufficient lateral deceleration. Several air bag system components get hot after inflation. Do not touch them after inflation. If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified...
Page 132 Seating and safety restraints SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Air Bag Supplemental Restraint System (SRS) in this chapter for special instructions about using air bags.
Page 133 Seating and safety restraints Do not leave children, unreliable adults, or pets unattended in your vehicle. To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards.
Page 134 Seating and safety restraints When installing a child safety seat: Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter. Use the correct safety belt buckle for that seating position. Insert the belt tongue into the proper buckle until you hear a snap and feel it latch.
Page 135 Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions 1. Position the child safety seat in a seat with a combination lap and shoulder belt. An air bag can kill or injure a child in a child seat. If you must use a forward-facing child seat in the front seat, move seat all the way back.
Page 136 Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until...
Page 137 Seating and safety restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt.
Page 138 Tether anchorage hardware kits (part number 613D74) including instructions, may be obtained at no charge from any Ford or Lincoln-Mercury dealer. Tighten the anchor according to specifications. Otherwise, the safety seat may not be properly secured and the child may be...
Page 139: Starting
PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Page 140 Starting Make sure the parking brake is set. Make sure the gearshift is in P (Park). 3. Turn the key to 4 (ON) without turning the key to 5 (START). CHECK GAGE CHECK ENGINE <FUEL DOOR DOOR AJAR RPMx1000 BRAKE Make sure the corresponding lights illuminate briefly.
Page 141 STARTING THE ENGINE 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 4 (ON). 2. If the temperature is above –12°C (10°F) and the engine does not start within five seconds on the first try, turn the key to OFF, wait ten seconds and try again.
Page 142 Starting Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes.
Page 143: Driving
Driving BRAKES Your service brakes are self-adjusting. Refer to the maintenance guide and or service guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 144 Driving ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned on and the engine is off. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced.
Page 145 The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). The parking brake is not recommended to stop a moving vehicle.
Page 146 Driving The air suspension shut-off switch is located in the cargo area behind the left rear quarter trim panel. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Normal vehicle operation does not require any action by the driver.
Page 147 Do not rock the vehicle for more than a few minutes. The transmission and tires may be damaged or the engine may overheat. Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle.
Page 148 Driving R (Reverse) With the gearshift in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift in N (Neutral), the vehicle can be started and is free to roll.
Page 149 Each time the vehicle is started, the transmission will automatically return to normal overdrive mode. Every time the vehicle is shut off and restarted, you must press the transmission control switch to cancel overdrive operation if driving in overdrive is not desired. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide...
Page 150 Driving Always set the parking brake fully and make sure the gearshift is securely latched in P (Park). Never leave your vehicle unattended while it is running. R (Reverse) With the gearshift in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse).
Page 151 Drive – Not shown on the display. Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in the position. The TCIL will illuminate on the instrument cluster. Transmission operates in gears one through four. more engine braking than (Overdrive) and is useful whenever driving conditions (i.e., city traffic, hilly terrain, etc.) cause the transmission to...
Page 152 Driving Forced Downshifts To gain acceleration in (Overdrive) or Drive (O/D OFF) when passing another vehicle, push the accelerator to the floor. The transmission will downshift to the appropriate gear: fourth, third, second or first gear. FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) When Four–wheel drive (4WD) is engaged, power is supplied to all four wheels through a transfer case.
Page 153 Positions of the Control-Trac system The Control-Trac system functions in three modes: The 4WD AUTO mode provides four-wheel drive with full power delivered to the rear axle, and to the front axle as required for increased traction. This is appropriate for normal on-road operating conditions, such as dry road surfaces, wet pavement, snow and gravel.
Page 154 Driving If your vehicle is equipped with 4WD or AWD, a spare tire of a different size than the road tires should never be used. Such a tire could result in damage to driveline components and make the vehicle difficult to control. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under...
Page 155 Shifting from 4WD LOW to 4WD AUTO or 4WD HIGH 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral). 4. Move the 4WD control to the 4WD AUTO or 4WD HIGH position. Driving off-road with 4WD Your vehicle is specially equipped for driving on sand, snow, mud and rough terrain and has operating characteristics that are somewhat...
Page 156 Driving Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels.
Page 157 When speed control is on and you are driving uphill, your vehicle speed may drop considerably, especially if you are carrying a heavy load. If vehicle speed drops more than 16 km/h (10 mph), the speed control will cancel automatically. Resume speed with accelerator pedal. If speed control cancels after climbing the hill, reset speed by pressing and holding the SET ACCEL button (to resume speeds over 50 km/h (30 mph).
Page 158 Driving Driving off-road with AWD Your vehicle is specially equipped for driving on sand, snow, mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road. Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside.
Page 159 Driving Once through water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. After driving through mud, clean off residue stuck to rotating driveshafts, halfshafts and tires.
Page 160 Driving Driving on snow and ice An AWD vehicle has advantages over 2WD vehicles in snow and ice but can skid like any other vehicle. Avoid sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop.
Page 161 GVWR (Gross Vehicle Weight Rating) : Maximum total weight of the base vehicle, passengers, optional equipment and cargo. The GVWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver’s door pillar. GAWR (Gross Axle Weight Rating) : Carrying capacity for each axle system.
Page 162 Driving The Certification Label, found on the inside pillar of the driver’s door, lists several important vehicle weight rating limitations. Before adding any additional equipment, refer to these limitations. If you are adding weight to the front of your vehicle, (potentially including weight added to the cab), the weight added should not exceed the Front Axle Reserve Capacity (FARC).
Page 163 Once through the water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. Driving through deep water where the transmission is submerged may allow water into the transmission and cause internal transmission damage.
Page 164 Driving Trailer towing table (4x2) GCWR (Gross Combined Weight Rating)/Trailer Weights Rear Maximum Engine axle GCWR-kg ratio (lbs.) 4.0L 4 082 3.55 SOHC (9 000) 4.0L 4 535 3.73 SOHC (10 000) 4 990 5.0L 3.73 (11 000) Trailer towing table (4x4 and AWD automatic transmission) 4.0L 4 082 3.55...
Page 165 Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. Hitches Do not use hitches that clamp onto the vehicle bumper. Use a load carrying hitch.
Page 166 Driving Never connect any trailer lighting to the vehicle’s taillamp circuits, because it may damage the electrical system resulting in fire. Contact your local Ford dealership for assistance in proper trailer tow wiring installation. Additional electrical equipment may be required. Using a step bumper The rear bumper is equipped with an integral hitch and requires only a ball with a 19 mm (3/4 inch) shank diameter.
Page 167 After you have traveled 80 km (50 miles), thoroughly check your hitch, electrical connections and trailer wheel lug nuts. When stopped in traffic for long periods of time in hot weather, place the gearshift in P (Park) and increase idle speed. This aids engine cooling and air conditioner efficiency.
Page 168 Driving To adjust cross-bar position: 1. Slide the locking switches at each end of the crossbar toward the rear of the vehicle until UNLOCKED appears. 2. Slide cross-bar to the desired location. 3. Lock the cross-bar into position by pushing the locking switches on each end of the crossbar toward the front of the vehicle.
Page 169: Roadside Emergencies
HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. The hazard lights control is located on top of the steering column. Depress hazard lights control to activate all hazard flashers simultaneously.
Page 170 Roadside emergencies The fuel pump shut-off switch is located in the passenger’s foot well, behind the kick panel. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse.
Page 171 Standard fuse amperage rating and color Fuse Mini Standard Rating Fuses Fuses Grey Grey Violet Violet Pink Pink 7.5A Brown Brown Blue Blue Yellow Yellow Natural Natural Green Green — — — — — — — — — — Roadside emergencies COLOR Cartridge Maxi...
Page 172 Roadside emergencies Passenger compartment fuse panel The fuse panel is located on the left hand side of the instrument panel facing the driver’s side door. Pull the panel cover outward to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover.
Page 173 The fuses are coded as follows: Fuse/Relay Fuse Amp Location Rating 7.5A Power Mirror Switch, Power Antenna 7.5A Blower Motor Relay, Air Bag Diagnostic Monitor 7.5A Left Stop/Turn Trailer Tow Connector Left Headlamp Data Link Connector (DLC) 7.5A Rear Blower Motor (Without EATC) 7.5A Right Stop/Turn Trailer Tow Connector Right Headlamp, Foglamp Relay...
Page 174 Roadside emergencies Fuse/Relay Fuse Amp Location Rating Flasher (Hazard) Auxiliary Power Socket — Not Used 7.5A Clutch Pedal Position (CPP) Switch, Starter Interrupt Relay, Anti-Theft 7.5A Generic Electronic Module (GEM), Instrument Cluster, Securi-Lock Battery Saver Relay, Electronic Shift Relay, Interior Lamp Relay, Electronic Shift Control Module DRL, Backup Lamps Switch, DTR Sensor 7.5A...
Page 175 Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Page 176 Roadside emergencies MEGAFUSE The high-current fuses are coded as follows: Fuse/Relay Fuse Amp Location Rating 60A** I/P Fuse Panel 40A** Blower Motor Relay 50A** 4 Wheel Anti-Lock Brake System (4WABS) Module 30A** Power Windows, Power Moon Roof, Power Seat 50A** Ignition Switch, Starter Relay 20A** Transfer Case Relay...
Page 177 Fuse/Relay Fuse Amp Location Rating 30A* Heated Backlight 15A* Fog Lamps and Daytime Running Lamps — Not Used 10A* Powertrain Control Module 30A* 4 Wheel Anti-Lock System (4WABS) Module 15A* Rear Wiper Motor 20A* Fuel Pump Relay and RAP Module 15A* Horn Relay 15A*...
Page 178 Roadside emergencies CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Spare tire information Your vehicle is equipped with a spare tire that must be used for emergencies only.
Page 179 Stowing the spare 1. Lay the tire on the ground with the valve stem facing up. 2. Slide the wheel under the vehicle and install the retainer through the wheel center. 3. Turn the jack handle clockwise until the tire is raised to its original position underneath the vehicle.
Page 180 Roadside emergencies When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is in P (Park). 3. Block the diagonally opposite wheel.
Page 181 6. Turn OFF the air suspension switch (if equipped). Refer to Air suspension system in the Driving chapter. 7. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 25 mm (1 inch) off the ground.
Page 182 Roadside emergencies To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. Never use the front or rear differential as a jacking point.
Page 183 JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter. Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted.
Page 184 Roadside emergencies Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Page 185 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor.
Page 186 Roadside emergencies 5. Be sure that the cables are clear of fan blades, belts and other moving parts of both engines. Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3.
Page 187 Roadside emergencies 4.0L SOHC...
Page 188 Roadside emergencies 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery. 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery.
Page 189 Roadside emergencies 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 190 Roadside emergencies If the vehicle is towed by other means or incorrectly, vehicle damage may occur. Do not tow with slingbelt equipment. Ford Motor Company has not developed or approved a T-hook or slingbelt towing procedure. A towing manual is available from Ford Motor Company for all authorized tow truck operators.
Page 191: Maintenance And Care
SERVICE RECOMMENDATIONS To help you service your vehicle: We highlight do-it-yourself items in the engine compartment for easy location. We provide a Scheduled Maintenance Guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.
Page 192 Maintenance and care Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the steering column on the instrument panel.
Page 193 Maintenance and care 2. Go to the front of the vehicle and release the auxiliary latch that is located in the center between the hood and the grill. 3. Lift the hood until the lift cylinders hold it open. IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1.
Page 194 Maintenance and care 5.0L V8 engine 1. Engine coolant reservoir 2. Windshield washer fluid reservoir 3. Engine oil filler cap 4. Automatic transmission fluid dipstick 5. Brake fluid reservoir 6. Battery 7. Power steering fluid reservoir 8. Engine oil dipstick 9.
Page 195 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). 4.0L V6 engine 5.0L V8 engine 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. If the oil level is between the ADD and FULL marks (4.0L engine) or between the MIN and MAX marks (5.0L engine), the oil level is acceptable.
Page 196 Maintenance and care If the oil level is below the ADD mark (4.0L engine) or MIN mark (5.0L engine), add enough oil to raise the level within the ADD-FULL range (4.0L engine) or MIN-MAX range (5.0L engine). Oil levels above the letter F in FULL (4.0L engine) or the MAX mark (5.0L engine) may cause engine damage.
Page 197: Capacities And Specifications
Maintenance and care Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty. Change your engine oil and filter according to the appropriate schedule listed in the Scheduled Maintenance Guide.
Page 198 Maintenance and care Brake fluid is toxic. If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the reservoir for the master cylinder run dry. This may cause the brakes to fail. WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever...
Page 199 ENGINE COOLANT Check the level of the engine coolant in the reservoir. Refer to the Scheduled Maintenance Guide for service interval schedules. Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become empty.
Page 200 Maintenance and care Check the coolant level in the coolant reservoir the next few times you drive the vehicle. If necessary, add enough of a 50/50 mixture of coolant and water to bring the liquid level to the fill line on the reservoir. Never remove the coolant reservoir cap while the engine is running or hot.
Page 201 Maintenance and care Recycled engine coolant Ford Motor Company recommends that Ford and Lincoln-Mercury dealers use recycled engine coolant produced by Ford-approved processes. For vehicles with green coolant, not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44–A, and use of such coolant may harm engine and cooling system components.
Page 202 Maintenance and care 4.0L SOHC V6 engine 5.0L V8 engine 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2.
Page 203 Maintenance and care TRANSMISSION FLUID Checking automatic transmission fluid Refer to your Scheduled Maintenance Guide for scheduled intervals for fluid checks and changes. Your transmission does not consume fluid. However, the fluid level should be checked if the transmission is not working properly, i.e., if the transmission slips or shifts slowly or if you notice some sign of fluid leakage.
Page 204 Maintenance and care The transmission fluid should be in this range if at normal operating temperature (66°C-77°C [150°F-170°F]). The transmission fluid should be in this range if at room temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result in transmission failure.
Page 205 Maintenance and care Checking and adding transfer case fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening.
Page 206 Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules.
Page 207 When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
Page 208 Maintenance and care Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective.
Page 209 INFORMATION ABOUT TIRE QUALITY GRADES New vehicles are fitted with tires that have their Tire Quality Grade (described below) molded into the tire’s sidewall. These Tire Quality Grades are determined by standards that the United States Department of Transportation has set. Tire Quality Grades apply to new pneumatic tires for use on passenger cars.
Page 210 Maintenance and care Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 211 Four tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial, bias-belted, or bias-type tires. Use only the tire sizes that are listed on the tire pressure decal.
Page 212 Maintenance and care Do not replace your tires with “high performance” tires or larger size tires. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer.
Page 213 WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision.
Page 214 Maintenance and care Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury. Fuels can also be harmful if absorbed through the skin.
Page 215 If the problems persist, see your dealer or a qualified service technician. The American Automobile Manufacturers Association (AAMA) issued a fuel specification to provide information on high quality fuels that optimize the performance of your vehicle. We recommend the use of fuels that meet the AAMA specification if they are available.
Page 216 Maintenance and care Running out of fuel Avoid running out fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: You may need to crank the engine several times before the system starts to pump fuel from the tank to the engine.
Page 217 If you do not use the proper fuel filler cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision. Fuel Filter Your vehicle is equipped with a fuel filter that is mounted on the underbody.
Page 218 Maintenance and care Filling the tank For consistent results: Use the same filling rate setting (low — medium — high) each time the tank is filled. Allow three automatic click-offs when filling. Always use the recommended octane rating of a known quality gasoline, preferably a national brand.
Page 219 Habits Smooth, moderate operation can yield up to 10% savings in fuel. Steady speeds without stopping will usually give the best fuel economy. Idling for long periods of time (greater than one minute) may waste fuel. Anticipate stopping; slowing down may eliminate the need to stop. Sudden or hard accelerations may reduce fuel economy.
Page 220 Maintenance and care Conditions Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. Carrying unnecessary weight may reduce fuel economy (approximately 2 km/h [1 mpg] is lost for every 180 kg [400 lb] of weight carried). Adding certain accessories to your vehicle (for example bug deflectors, rollover/light bars, running boards, ski/luggage racks) may reduce fuel economy.
Page 221 EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work properly: Use only unleaded fuel.
Page 222 Maintenance and care Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, items, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working.
Page 223 Turn signals License plate lamp Tail lamps Back-up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect lamp performance. Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children’s reach.
Page 224 Maintenance and care 3. Remove the bulb retaining ring by rotating it counterclockwise (when viewed from the rear) about 1/8 turn to free it from the bulb socket, and slide the ring off the plastic base. Keep the ring to retain the new bulb.
Page 225 Maintenance and care 1. Rotate bulb socket counterclockwise about ⁄ turn and remove from lamp assembly. 2. Carefully pull bulb straight out of socket and push in the new bulb. 3. Install bulb socket in lamp assembly by turning clockwise. 4.
Page 226 Maintenance and care License plate lamp bulbs To change the license plate bulbs: 1. Remove two screws and the license plate lamp assembly from the liftgate. 2. Remove bulb socket from lamp assembly by turning counterclockwise. 3. Pull the bulb out from socket and push in the new bulb.
Page 227: Customer Assistance
AIMING THE HEADLAMPS The alignment of your headlamps should be checked by a qualified service technician if: Oncoming motorists frequently signal you to deactivate your high beams, and your high beams are not activated. The headlamps do not seem to provide enough light for clear night vision.
Page 228 Maintenance and care Waxing your vehicle Wax when water stops beading on the surface. This could be every three or four months, depending on operating conditions. Use only carnauba or synthetic-based waxes. Use cleaning fluid or alcohol with a clean cloth to remove any bugs and tar before waxing vehicle.
Page 229 5.0L 4.0L SOHC Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning the wheels Wash with the same detergent as the body of your vehicle. Do not use acid-based or alcohol-based wheel cleaners, steel wool, fuel or strong detergents.
Page 230 Maintenance and care Underbody Flush the complete underside of vehicle frequently. Keep body drain holes unplugged. Inspect for road damage. Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners.
Page 231 Maintenance and care Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.
Page 232 Maintenance and care Woodtone trim Wipe stains with a soft cloth and a multi-purpose cleaning solution. Inside windows Use glass cleaner for the inside windows if they become fogged. Cleaning mirrors Do not clean your mirrors with a dry cloth or abrasive materials. Use a soft cloth and mild detergent and water.
Page 233: Capacities And Specifications
Capacities and specifications MOTORCRAFT PART NUMBERS Component 4.0L SOHC V6 engine Air filter FA-1658 Fuel filter FG-986B Battery (standard) BXT-65-650 Battery (optional) BXT-65-750 Oil filter FL-1A PCV valve EV-225 Spark plugs* AGRF-22P * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information.
Page 234 Capacities and specifications Fluid Ford Part Name Transmission Motorcraft fluid MERCON V Transfer case Motorcraft MERCON Engine coolant See footnote Front axle fluid Motorcraft 80W90 Axle Lubricant Rear axle Motorcraft SAE lubricant 80W90 Premium Rear Axle Lubricant Motorcraft SAE 75W140 High Performance Synthetic Rear Axle Lubricant...
Page 235 Capacities and specifications If your engine coolant is green in color, use Ford Premium Cooling System Fluid. If your coolant is orange in color, use Ford Extended Life Engine Coolant. Refer to Adding engine coolant, in the Maintenance and Care chapter. Fill to 6 mm to 14 mm (1/4 inch to 9/16 inch) below bottom of fill hole.
Page 236 Capacities and specifications Ford part Item name or equivalent Driveshaft, slip Premium Long spline, universal Life Grease joints Engine coolant Ford Premium Engine Coolant (green in color) Ford Extended Life Engine Coolant (orange in color) Motorcraft 5W30 Engine oil Super Premium Motor Oil Automatic Motorcraft...
Page 237 Capacities and specifications Ford part Item name or equivalent Ultra-Clear Windshield Windshield washer fluid Washer Concentrate If your engine coolant is green in color, use Ford Premium Cooling System Fluid. If your coolant is orange in color, use Ford Extended Life Engine Coolant.
Page 238 Capacities and specifications VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width (3) Overall height (4) Wheelbase (5) Track - Front (5) Track - Rear mm (in) 4 788 (188.5) 1 783 (70.2) 1 725 (67.9) 2 835 (111.6) 1 486 (58.5) 1 487 (58.5)
Page 239 Capacities and specifications IDENTIFYING YOUR VEHICLE Safety compliance label The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the front door latch pillar on the driver’s side.
Page 240 Capacities and specifications Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. For your protection, you will also find the vehicle identification number in the following areas (if applicable): the left and right front fenders the left and right front doors the front and rear bumpers...
Page 241: Reporting Safety Defects
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company.
Page 242: Index
Index Air bag supplemental restraint system ...125 and child safety seats ...127 description ...126,129 disposal ...131 indicator light ...129,131 passenger air bag ...127,130 Air conditioning automatic temperature control system ..24,25,26,27,28,29 rear seat controls ...30 Air suspension description ...145 warning light ...10 All Wheel Drive (AWD), driving off road ...157 Armrests ...103...
Page 243 Exhaust fumes ...142 Floor mats ...103 Four-Wheel Drive vehicles ...9,10,152 control trac ...152 description ...153,154,155 driving off road ...155,158 electronic shift ...32 Fuel choosing the right fuel ...214 comparisons with EPA fuel economy estimates ...220 detergent in fuel ...215 filling your vehicle with fuel ...213, gauge ...15 quality ...215 running out of fuel ...216...
Page 244 Index economy button ...17 english/metric button ...16 reset button ...17 system check button ...17,18 Mirrors automatic dimming rearview mirror ...98 cleaning ...232 heated ...101 side view mirrors (power) ...101 Moon roof ...89 Motorcraft parts ...217 Octane rating ...215 Odometer ...13 Panic alarm feature, remote entry system ...106 Parking brake ...144...
Page 245 Universal transmitter (see garage door opener) ...92,93, 94,95,96 Vehicle dimensions ...238 Vehicle Identification Number (VIN) ...240 Vehicle loading ...160 Ventilating your vehicle ...142 Warning chimes ...6 Washer fluid ...198 Index reservoir ...198 Water, Driving through ...162 Windows ...99,100 rear wiper/washer ...86 Windshield washer fluid and wipers checking and cleaning ...208...
Page 248: Filling Station Information
Filling station information Item Recommended fuel Fuel tank capacity Engine oil capacity (includes filter change) Tire size and pressure Hood release Coolant capacity-(4.0L SOHC V6 engine) Coolant capacity (5.0L V8 engine) Power steering fluid capacity Automatic transmission fluid capacity (4R70W with 5.0L V8 engine AWD) Automatic transmission fluid capacity (4x2 vehicles with 5R55E...

This manual is also suitable for:

Mountaineer 1999Mountaineer 1998

Mercury 1999 Mountaineer Owner's Manual

Quick Links

Related Manuals for Mercury 1999 Mountaineer

Summary of Contents for Mercury 1999 Mountaineer

This manual is also suitable for:

Table of Contents