Page 1: Table Of Contents
Before driving Introduction Instrumentation Controls and features Seating and safety restraints Starting and driving Starting Driving Roadside emergencies Servicing Maintenance and care Capacities and specifications Customer assistance Reporting safety defects Index All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company.
Page 2: Introduction
Introduction ICONS Indicates a safety alert. Read the following section on Warnings. Indicates vehicle information related to recycling and other environmental concerns will follow. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment.
Page 3: Instrumentation
Instrumentation...
Page 4 Instrumentation Headlamp control (pg. 19) Turn signal and wiper/washer control (pg. 86) Speed control (pg. 85) Driver side air bag (pg. 131) * if equipped Instrument cluster Panel dimmer (pg. 19) AUTO AUTO PUSH INTERIOR CRUISE Audio controls * (pg. 85) (pg.
Page 5 Gearshift (including overdrive button) Hazard flasher (pg. 161) VOL - PUSH ON BASS TREB SEEK SCAN TUNE DISCS OFF REAR 1 Instrumentation Rear wiper/washer (pg. 87) (pg. 171) Rear defroster Electronic sound system FADE TAPE SIDE 1 - 2 COMP SHUFFLE (pg.
Page 6: Warning Lights And Chimes
Instrumentation WARNING LIGHTS AND CHIMES Standard analog instrument cluster RPMx1000 BRAKE Optional electronic instrument cluster ˚F ˚C MILES/BAL L/100 km OUTSIDE TEMP INST ECONOMY AVG. ECONOMY TO EMPTY BRAKE Charging system Illuminates when the ignition is turned to the ON position and the engine is off.
Page 7 Instrumentation Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Brake system warning Momentarily illuminates when the ignition is turned to the ON position.
Page 8 Instrumentation Turn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster, check for a burned-out turn signal bulb. Refer to Exterior bulbs in the Maintenance and care chapter.
Page 9 Instrumentation Service engine soon Your vehicle is equipped with a SERVICE computer that monitors the engine’s ENGINE emission control system. This SOON system is commonly known as the On Board Diagnostics System (OBD II). The OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
Page 10 Instrumentation Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity. Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.
Page 11: Headlamps On Warning Chime
Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the ignition is off (and the key is not in the ignition) and the driver’s door is opened. GAUGES Standard analog instrument cluster gauges RPMx1000 BRAKE Optional electronic instrument cluster gauges ˚F ˚C MILES/BAL L/100 km...
Page 12 Instrumentation Standard analog instrument cluster Optional electronic instrument cluster Speedometer Indicates the current vehicle speed. Standard analog instrument cluster Optional electronic instrument cluster RPMx1000 CRUISE km/h X 1000 TRIP 1 TRIP 2 50 60 km/h CRUISE km/h X 1000 TRIP 1 TRIP 2...
Page 13 Odometer Registers the total kilometers (miles) of the vehicle. Standard analog instrument cluster Optional electronic instrument cluster Refer to Electronic Message Center for information on how to switch the display from metric to English measurements. Trip odometer Registers the kilometers (miles) of individual journeys. Standard analog instrument cluster To reset, depress the control.
Page 14 Instrumentation empty indication, the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel. Standard analog instrument cluster Optional electronic instrument cluster Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H”...
Page 15 Optional electronic instrument cluster ELECTRONIC MESSAGE CENTER (IF EQUIPPED) The electronic message center only works when the ignition is in the ON position. The message center allows you to: display the outside temperature. change your gauges from english to metric units. monitor the instantaneous fuel economy.
Page 16 Instrumentation OUTSIDE TEMP INST ECONOMY AVG ECONOMY TO EMPTY RESET Press this control to reset the average fuel economy calculation. ENG/MET Press this control to change your instrument cluster gauges from english to metric. To switch the Electronic Automatic Temperature Control (if equipped) display between Fahrenheit and Celsius, refer to Temperature conversion in the Controls and Features chapter.
Page 17 INST ECONOMY Press SELECT until the menu displays INST ECONOMY. This will display your fuel economy in liters/100 km or miles/gallon based on the type of traffic you are in. Your vehicle must be moving to calculate instantaneous fuel economy. When your vehicle is not moving, this function shows 99.9 L/100km or 0.0 MILES/GAL.
Page 18 Instrumentation 2. Select AVG ECONOMY. 3. Press the RESET control to clear the system memory. Actual highway fuel economy is now displayed. This current average measure will change as the speed control system changes the engine speed to maintain a constant vehicle speed.
Page 19: Controls And Features
PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. Push and hold top of control to brighten. Push and hold bottom of control to dim. HEADLAMP CONTROL Rotate the headlamp control clockwise to the first position to turn on the parking lamps.
Page 20 Controls and features High beams Push forward to activate. Pull toward you to deactivate. Flash to pass Pull toward you to activate and release to deactivate. AUTOLAMP CONTROL (IF EQUIPPED) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
Page 21 Controls and features CLIMATE CONTROL SYSTEM Manual heating and air conditioning system CLIMATE CONTROL SYSTEM Fan speed control Controls the volume of air circulated in the vehicle. Temperature control Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
Page 22 Controls and features The air conditioning operates in MAX A/C and when the A/C control is depressed. However, the air conditioning will only function if the outside temperature is about 4°C (40°F) or higher. Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle.
Page 23 and air conditioning capabilities are provided in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot and full cold positions, the air distributed through the front and rear floor ducts will be slightly warmer than the air sent to the windshield defroster ducts.
Page 24 Controls and features Rear seat heating Rear seat heating is provided through the floor ducts located under the front seats. Airflow and temperature to the rear seating are regulated by the main climate control system. OFF REAR A/C 1 The rear passenger compartment air conditioning system (if equipped) should be set to OFF, if rear heating is desired.
Page 25 Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield under the hood). If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
Page 26 Controls and features The rear A/C fan speed control allows the rear passengers to control the volume of air that is distributed from the rear registers. REAR The rear seat A/C system is controlled from the main climate control system on the instrument panel. OFF REAR A/C 1...
Page 27 Controls and features Turning the Rear A/C on OFF REAR A/C 1 1. Set the main climate control rear fan control to Rear A/C, set the mode selector in any position (other than OFF), and depress the A/C control. 2. Set the fan speed on the Rear A/C fan control to a number between 1–4.
Page 28 Controls and features Turning the Rear A/C off: OFF REAR A/C 1 To turn the Rear A/C off, turn the Rear Fan Control on the main climate control system to OFF, or OFF REAR A/C 1 REAR turn the Rear Fan Control on the main climate control system to Rear A/C and turn the Rear A/C Fan Control to 0.
Page 29 Controls and features Electronic Automatic Temperature Control (EATC) system (if equipped) OFF REAR 1 TEMP AUTOMATIC The EATC system will maintain a selected temperature and automatically control airflow. You can override automatic operation with any of the override controls or the fan speed control. Turning the EATC on OFF REAR 1 TEMP...
Page 30 Controls and features Turning the EATC off Press OFF. OFF REAR 1 TEMP AUTOMATIC Automatic operation Press AUTOMATIC and select the desired temperature. The selected temperature and the word AUTO will appear in the display window. The EATC system will either heat or cool to achieve the selected temperature.
Page 31 Controls and features To control the temperature, select any temperature between 15°C (60°F) and 32°C (90°F) by pressing the temperature controls. OFF REAR 1 TEMP AUTOMATIC For continuous maximum cooling, push the temperature control until 15°C (60°F) is shown in the display window. The EATC will continue maximum cooling (disregarding the displayed temperature) until a warmer temperature is selected by pressing the temperature controls.
Page 32 Controls and features Fan speed ( When AUTOMATIC is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, use the thumbwheel to cancel automatic fan speed operation. Rotate the thumbwheel up for higher fan speed or down for lower fan speed.
Page 33 Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle. Under normal conditions, your vehicle’s climate control system should be left in any position other than MAX or OFF when the vehicle is parked.
Page 34 Controls and features MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more economical and will cool the inside of the vehicle faster. After pressing the MAX control, both the MAX and A/C indicators will light and the airflow will be from the instrument panel registers.
Page 35 Rear seat heating Rear seat heating is provided through the floor ducts located under the front seats. Airflow and temperature to the rear seating are regulated by the main climate control system. OFF REAR A/C 1 The rear passenger compartment air conditioning system (if equipped) should be set to OFF, if rear heating is desired.
Page 36 Controls and features Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield). If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
Page 37 Controls and features The rear A/C fan speed control allows rear passengers to control the volume of air that is distributed from the rear registers. The rear A/C system is controlled from the main climate control system on the instrument panel. The rear seat A/C system is controlled from the main climate control system on the instrument panel.
Page 38 Controls and features Turning the Rear A/C on 1. Set the main climate control rear fan control to Rear A/C, set the mode selector in any position (other than OFF), and depress the A/C control. 2. Set the fan speed on the Rear A/C fan control to a number between 1–4.
Page 39 OFF REAR A/C 1 REAR turn the Rear Fan Control on the main climate control system to Rear A/C and turn the Rear A/C Fan Control to 0. For maximum cooling for the front seat passengers, set the rear fan switch to the OFF (0) position.
Page 40 Controls and features The ignition must be in the ON position to operate the rear window defroster. The defroster turns off automatically after 15 minutes or when the ignition is turned to the OFF position. To manually turn off the defroster before 15 minutes have passed, push the control again.
Page 41 Turn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD changer modes...
Page 42 Controls and features Tune adjust in radio mode Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. Press to move to the next frequency up the band (whether or not a listenable station is located there).
Page 43 Press to seek forward to the next track of the current disc. After the last track has been completed, the first track of the current disc will automatically replay. Scan function The scan function works in radio or CD changer mode (if equipped). Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band.
Page 44 Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. BASS Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. TREB Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers.
Page 45 Tape select To enter tape mode while in radio or CD changer mode, press the TAPE control. If no tape is found, NO TAPE appears in the display. Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection being played or to skip to the next selection.
Page 46 Controls and features Press the 1–2/FF control to stop rewinding the tape. To rewind in CD changer mode, press the CD control (preset 1). Press the control again to deactivate rewind mode. Fast forward The fast forward control works in tape and CD changer modes. To fast forward in tape mode, press the 1–2/FF control.
Page 47 Controls and features The shuffle feature continues to the next disc after all tracks are played. Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again. Tape direction select Press SIDE and 1–2 at the same SIDE 1 - 2 time to play the alternate side of a...
Page 48 Controls and features to decrease hours and to increase hours. To set the minute, press and hold the CLK control and press the TUNE control: to decrease minutes and to increase minutes. The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time).
Page 49 Rear seat controls (if equipped) The Rear Seat Controls (RSC) allow the rear seat passengers to operate the radio, tape, or CD changer (if equipped). To turn on the rear seat controls, press the memory preset controls 3 and 5 at the same time. The Pressing 3 and 5 at the same time again will turn the rear seat controls off.
Page 50 Controls and features Using headphones Plug a 3.6 mm headphone (not included) into either one of the two jacks. Press the to operate the headphones. The speakers will cut out once the speaker on/off control is pressed. Press the deactivate headphones. Media select Push the MEDIA control to toggle between AM, FM1, FM2, tape, or CD...
Page 51 Premium AM/FM Cassette (CD changer compatible) PUSH ON TAPE SEEK MUTE Your audio system is equipped with selective lighting, a unique lighting strategy. This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off.
Page 52 Controls and features Turn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD changer modes...
Page 53 disc unless the CD changer is in shuffle mode.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the disc. Press to select the next disc in the CD changer. Hold the control to fast-forward through the remaining discs. Seek function The seek function control works in radio, tape or CD changer mode (if equipped).
Page 54 Controls and features Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape.
Page 55 Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
Page 56 Controls and features Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Tape/CD changer mode select (if equipped) To begin tape play (with a tape loaded into the audio system) while in the radio or CD changer mode, press the TAPE control.
Page 57 In CD changer mode, pressing the control for less than three seconds results in slow forward action. Pressing the control for more than three seconds results in fast forward action. Tape direction select Press SIDE 1–2 to play the alternate side of a tape.
Page 58 Controls and features Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again. Radio Data System (RDS) feature When selected, the RDS (Radio Data System) function performs the following: Displays the radio station call letters Displays the type of music format (jazz, country, rock) Searches for a particular type of music format by selecting the SEEK...
Page 59 Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: Classic Country Info Jazz Oldies R & B Religious Rock Soft Top 40 Show With RDS activated, press the...
Page 60 Controls and features Use the SEL control to manually set the time. Press to increase hours/minutes. Press to decrease hours/minutes. Mute mode Press the control to mute the playing media. Press the control again to return to the playing media. Rear seat controls (if equipped) The Rear Seat Controls (RSC) allow the rear seat passengers to operate...
Page 61 Adjusting the volume Press the + control to increase volume. Press the — control to decrease volume. From the RSC, the speaker volume can not be set higher than the current volume radio setting. Once in headphone mode, the RSC volume controls will only change volume in the headphones to a desired level (muting the speakers will not mute the headphones).
Page 62 Controls and features Memory preset control Push the MEM control successively to allow rear sear passengers to scroll through the 6 memory presets in AM, FM1, or FM2. Push the MEM control in CD changer mode (if equipped) to advance to the next disc. Seek function Press to find the next...
Page 63 Controls and features Your audio system is equipped with selective lighting, a unique lighting strategy. This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off. Those controls which have a function for the specific mode of operation selected will be lit, while the controls which have no function for that mode will be turned off.
Page 64 Controls and features AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play. AM/FM select in CD mode Press this control to stop CD play and begin radio play.
Page 65 Seek function in radio mode Press to find the next listenable station down the frequency band. Press to find the next listenable station up the frequency band. Seek function in tape mode Press to listen to the previous selection on the tape. Press to listen to the next selection on the tape.
Page 66 Controls and features Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’s first side, direction automatically reverses to the opposite side of the tape.) To stop on a particular selection, press the control again.
Page 67 Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
Page 68 Controls and features to decrease treble output and to increase treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: to shift sound to the left and to shift sound to the right.
Page 69 Tape/CD/CD changer (if equipped) select To begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the TAPE control. Press the button during rewind or fast forward to stop the rewind or fast forward function.
Page 70 Controls and features Tape direction select Press SIDE 1–2 to play the alternate side of a tape. Eject function Press the control to stop and eject a tape. Press the control to stop and eject a Dolby noise reduction Dolby noise reduction reduces the amount of hiss and static during tape playback.
Page 71 Setting the clock Press the RDS/CLK control until SELECT HOUR is displayed and press: to decrease hours and to increase hours. To set the minute, press the RDS/CLK control until SELECT MIN is displayed and press: to decrease minutes and to increase minutes.
Page 72 Controls and features Press the RDS control. Use the SEL control to select ON or OFF to enable or disable the feature. RDS traffic announcement When set ON, this traffic feature will interrupt tape or CD play to play a traffic report broadcast from a FM RDS station.
Page 73 Jazz/R&B Religious Rock Soft Top 40 RDS show RDS sends information with the FM broadcast, including: station name, station type, and/or radio text. To view this information: With the RDS menu enabled, press the RDS control until SHOW is displayed. Use the SEL control to select TYPE, NAME, TEXT or NONE.
Page 74 Controls and features To turn on the rear seat controls, press the memory preset controls 3 and 5 at the same time. The Pressing 3 and 5 at the same time again will turn the rear seat controls off. If there is a discrepancy between the rear seat and the front audio controls, (i.e, both trying to listen to the same playing media), the front audio system will receive the desired selection.
Page 75 The rear speakers will cut out once the speaker on/off control is pressed. A soft audible sound may be heard from the rear speakers. The front speaker will remain playing for the front passengers. Press the control again to deactivate headphones (Personal Audio System). Media select Push the MEDIA control to toggle between AM, FM1, FM2, tape, CD,...
Page 76 Controls and features CD changer (if equipped) The CD changer is located in the center console of your vehicle. 1. Slide the door to access the CD changer magazine. 2. Press to eject the magazine. 3. Turn the magazine (A) over. 4.
Page 77 Controls and features If you pull too hard on the disc holder, the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A). 5. Line up the CD with the groove of the disc holder.
Page 78 Controls and features The CD magazine may be inserted or ejected with the radio power on or off. ONLY use the magazine type supplied with the CD changer, other types will damage the unit. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty.
Page 79 Cleaning cassette player Clean the tape player head with a cassette cleaning cartridge after ten to twelve hours of play in order to maintain the best sound and operation. Cassette and cassette player care Use only cassettes that are 90 minutes long or less. Do not expose tapes to direct sunlight, high humidity, extreme heat or extreme cold.
Page 80 Controls and features Station overload. Weak signals are sometimes captured by stronger signals when you pass a broadcast tower. A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed. The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo.
Page 81 POSITIONS OF THE IGNITION 1. OFF/LOCK, shuts off the engine and all accessories/locks the steering wheel, gearshift lever and allows key removal. 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running. 3.
Page 82 Controls and features To turn speed control off Press OFF. Once speed control is switched off, the previously programmed set speed will be erased. To set a speed Press COAST/SET. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).
Page 83 To set a higher set speed Press and hold RES/ACCEL. Release the control when the desired vehicle speed is reached Press and release RES/ACCEL. Each press will increase the set speed by 1.6 km/h (1 mph) or Accelerate with your accelerator pedal.
Page 84 Controls and features To disengage speed control Depress the brake pedal. Press CANCEL. Disengaging the speed control will not erase the previously programmed set speed. Press OFF. Pressing OFF will erase the previously programmed set speed. ACCEL CANCEL COAST CRUISE...
Page 85 To return to a previously set speed Press RES/ACCEL. For RES/ACCEL to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on in the instrument cluster when either the COAST/SET or RES/ACCEL controls are pressed.
Page 86 Controls and features In any mode: Press VOL up or down to adjust the volume. TURN SIGNAL CONTROL Push down to activate the left turn signal. Push up to activate the right turn signal. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position.
Page 87 Rear window wiper and washer Press the wiper control to activate the rear wiper. Press again to turn off the wiper. The wiper operates at a pre-set interval. Press the washer control to activate the rear washer. The wiper will come on when the washer control is pressed, if it is not already on.
Page 88 Controls and features Deactivating overdrive Press the Transmission Control Switch (TCS) located on the end of OVERDRIVE OFF/ON the gearshift lever. The O/D OFF indicator light will illuminate. The transaxle will operate in all gears except overdrive. To return to normal overdrive mode, press the Transmission Control Switch again.
Page 89 POWER WINDOWS Press and hold the switch to open. Pull up and hold the switch to close. Power vent windows (if equipped) Your vehicle may be equipped with rear power vent windows which are operated the same as the front power windows.
Page 90 Controls and features Accessory delay With accessory delay, the window and moonroof switches may be used for up to 15 minutes after the ignition switch is turned to the OFF position or until either of the front doors are opened. POWER DOOR LOCKS Push control forward to unlock all doors and pull backward to lock all...
Page 91 Controls and features Pull lock control out to engage the lock. Push control in to disengage childproof locks. POWER SIDE VIEW MIRRORS The ignition must be in ACC or ON position to adjust the power side view mirrors. To adjust your mirrors: 1.
Page 92 Controls and features 2. Move the control in the direction you wish to tilt the mirror. MIRRORS 3. Return to the center position to lock mirrors in place. Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated.
Page 93 HOMELINK UNIVERSAL TRANSCEIVER WITH TRAVELNOTE (IF EQUIPPED) The HomeLink Universal Transceiver, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most current transmitters to operate garage doors, entry gates, security systems, entry door locks, and home or office lighting.
Page 94 Controls and features 4. The red light will flash slowly and then rapidly. Release both buttons when the red light flashes rapidly. 5. Follow steps 2 through 4 to program the remaining two buttons. If you do not successfully program the HomeLink Universal Transceiver after repeated attempts, refer to Rolling code programing which follows, or call toll-free customer assistance: 1–800–355–3515 or on the Internet at HomeLink.jci.com.
Page 95 The hand-held transmitter appears to program the HomeLink Universal Transceiver but does not activate the device. Press and hold the trained HomeLink button. The device has the rolling code feature if the indicator light flashes rapidly and then turns solid after 2 seconds. After completing the “Programming”...
Page 96 Controls and features 1. Press and hold the desired HomeLink button. Do NOT release until step 4 has been completed. 2. When the indicator light begins to flash slowly (after 20 seconds), position the hand-held transmitter 5–14 cm (2 to 5 inches) away from the HomeLink surface.
Page 97 To play a message: 1. Press and release the PLAY button to play the message. 2. Press and hold the PLAY button to hear all the messages in consecutive order starting with the most recent. 3. If the PLAY button is pressed while a message is being listened to, TravelNote will skip to the beginning of the next message.
Page 98 Controls and features Storage bin (if equipped) The storage compartment may be used to store small objects. Push in to open or close the cover. Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: Remove the GARAGE control button from the storage...
Page 99 Place the provided height adaptors on the back of the GARAGE control button as needed. Place the GARAGE control button in the storage compartment. Close cover and press the GARAGE control button to activate the transmitter. INTERIOR LAMPS Dome lamps The front dome lamp is located overhead between the driver and passenger seats.
Page 100 Controls and features MOON ROOF (IF EQUIPPED) To operate the moon roof: To open, press and hold the rear portion of the control. This will fully open the moon roof. To close, press and hold the front portion of the control. To operate the moon roof vent position: To open, press and hold the front...
Page 101 Controls and features Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will LOCK illuminate and the parking and tail lamps will flash once. PANIC LOCK Press the control a second time within five seconds to unlock all doors.
Page 102 Controls and features This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Page 103 To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new battery up. Refer to the diagram inside the transmitter unit.
Page 104 Controls and features ANTI-THEFT SYSTEM (IF EQUIPPED) When armed, the anti-theft system will help prevent your vehicle from unauthorized entry. If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting.
Page 105 If a door is open, the system is prearmed and is waiting for the door to close. Once all the doors are closed, the security indicator lamp on the instrument panel will illuminate continuously when the system is prearmed. Once the doors are closed, the system will arm in 30 seconds and the security indicator lamp will begin to flash.
Page 106 Controls and features Disarming a triggered anti-theft system You can disarm the system by any of the following actions: Press the unlock control. Unlock the doors with a key. LIFTGATE To open the liftgate window (if equipped), insert key into lock and turn clockwise.
Page 107 Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle.
Page 108 Controls and features Front Cargo net The front cargo net can be used to hold small items between the front seats. To install the net, secure the hooks into the retainers located on the inboard base of the front seats. Parcel Shelf (if equipped) Your vehicle may be equipped with a 14 kg (30 lbs.) maximum capacity...
Page 109 To secure objects on the shelf: 1. Disconnect the net loops from the retainers underneath the shelf. 2. Place the objects underneath the net and secure the net loops to the retainers underneath the shelf. All objects loaded on the cargo shelf MUST BE SECURED UNDER THE CARGO NET.
Page 110: Seating And Safety Restraints
Seating and safety restraints SEATING Adjustable head restraints Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 111 Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision. Lift handle to move seat forward or backward.
Page 112 Seating and safety restraints Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision. Move the control up or down to move the seat up and down.
Page 113 Seating and safety restraints The lumbar control is located on the inboard side of the driver’s seat. Move the control up or down to adjust lumbar support. Memory seats and mirrors (if equipped) The memory seat control is located on the driver’s door panel. The control operates with the ignition in the OFF position or the ignition is in the ON position and the vehicle is in...
Page 114 Seating and safety restraints 2. Press and hold the desired memory position button. Within ten seconds, press the unlock button on the transmitter while the memory button is pressed. 3. When the transmitter has been programmed, the indicator will flash five times.
Page 115 4 passenger vehicle (with third row seat in storage position) A. Cargo mat B. Narrow mats C. Sliding door mats, LH/RH 5 passenger vehicle (second row seats removed) A. Cargo mat B. Narrow mats C. Sliding door mats, LH/RH Seating and safety restraints...
Page 116 Seating and safety restraints 5 passenger vehicle (second row seats removed and third row bench seat moved forward to limousine seating position) A. Cargo mat B. Narrow mats Two passenger vehicle (second row seats removed and third row seat stored in full forward position) A.
Page 117 Bucket seat (driver’s side only) - inboard side of seat base Use only soft cups in the cupholder. Hard objects can injure you in a collision. Adjusting 2nd row bench Pull control up to flip seatback to forward flat position. Seating and safety restraints...
Page 118 Seating and safety restraints 2nd row bucket seats (if equipped) Adjusting the left side bucket seat Pull control up to recline the seatback or fold the seatback flat. Adjusting the right side (E-Z Entry Tip Slide) bucket seat The E-Z Entry Tip Slide seat allows for easier entry and exit to and from the 3rd row seat.
Page 119 Seating and safety restraints To exit the third row seat, pull up on the 3rd row access control. To return the seat to a seating position, move the seat rearward until the seat track locks. Then readjust the seatback. Lift handle to move the seat forward or backward.
Page 120 Seating and safety restraints Pull control up to flip seatback to a forward flat position. Adjusting 3rd row bench Pull control up to adjust seatback position. This control will also allow the seatback to be put in the forward flat position.
Page 121 Seating and safety restraints The entire seat can be moved to four seating positions and two storage positions. Before rearranging the seats, remove any floor mats that might be in the way, see Removable floor mats in this chapter for instructions on placement of floor mats.
Page 122 Seating and safety restraints To move the seat to another seating or storage position: 1. Lift control (A) to release the seat cushion and flip the cushion up. The seat cushion must be moved to the storage position before the seat can be moved along the track.
Page 123 After sliding the seat, check to ensure that both sides of the seat are locked in position. This must be done before the vehicle is put into motion in order to prevent unintended movement of the seat. Every time you adjust any seat, check to be sure that it is properly latched in the lock position of both seat tracks.
Page 124 Seating and safety restraints To install the seat: The bucket seats are not interchangeable due to the locations of the seat anchors on the floor of the vehicle. Each seat must be installed in its original position. 1. Position the seat in the vehicle. 2.
Page 125 It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Page 126 Seating and safety restraints 2. To unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free...
Page 127 How to use the automatic locking mode Buckle the combination lap and shoulder belt. Grasp the shoulder portion and pull downward until the entire belt is extracted. Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Page 128 Seating and safety restraints Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height adjuster down.
Page 129 Seating and safety restraints Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle.
Page 130 Seating and safety restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON...
Page 131 AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) 50 60 TEMP FUEL AUTO 0 0 0 AUTO PUSH INTERIOR CRUISE Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
Page 132 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer.
Page 133 Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
Page 134 Seating and safety restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
Page 135 The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors. Determining if the system is operational The SRS uses a readiness light in the instrument cluster to indicate the condition of the system.
Page 136 Seating and safety restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use.
Page 137 SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Page 138 Seating and safety restraints Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps.
Page 139 Seating and safety restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
Page 140 Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Page 141 Installing child safety seats in the lap belt seating positions 1. Lengthen the lap belt. To lengthen the belt, hold the tongue so that its bottom is perpendicular to the direction of webbing while sliding the tongue up the webbing. 2.
Page 142 Seating and safety restraints Seat Type/Position 3-passenger/3rd row position 2-passenger bench or bucket/2nd row child seat position 3-passenger/2nd row –Outboard 3-passenger/2nd row –Center Tether strap anchorage locations have been provided in your vehicle. The left side of the figure is the front of the vehicle.
Page 143 Seating and safety restraints Second row seats 1. Position the child safety seat on the passenger seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Grasp the tether strap and position it to the seat frame.
Page 144 Seating and safety restraints 4. Rotate the tether strap. 5. Clip the tether strap to the seat tether slot bracket at the lower rear portion of the seatback. If the tether strap is clipped incorrectly (as shown) the child safety seat may not be retained properly in the event of a collision.
Page 145 Seating and safety restraints 6. Rotate the tether strap clip. 7. Refer to the instructions in this section under Installing child safety seats in combination lap and shoulder belt seating positions to secure the child safety seat. 8. Tighten the child safety seat tether strap according to the manufacturer’s instructions.
Page 146 Tether anchorage hardware kits (part number 613D20) including instructions, may be obtained at no charge from any Ford or Lincoln-Mercury dealer. All vehicles built for sale in Canada include a tether anchor hardware kit. Be sure to follow the child safety seat manufacturer’s instructions.
Page 147 Seating and safety restraints Third row bench in second row position To attach a tether strap to a lap/shoulder belt: 1. Route the tether strap under the head restraint and between the head restraint supports. 2. Hook the tether strap hook into the large hole at the end of the seat belt tongue of the lap/shoulder belt directly behind the child seat...
Page 148 Seating and safety restraints BUILT-IN CHILD SEATS Built-in child safety seat (if equipped) The 2nd row seat may include a built-in child seat. This child seat conforms to all Federal and local motor vehicle safety standards. Read the labels located on the child seat cushion for information on the built-in child seat.
Page 149 Seating and safety restraints 1. Pull the release strap near the bottom of the seatback. 2. Grasp the child seat at the top of the seatback and pull the top forward to release the latch. 3. Continue to unfold the child seat until it rests on the seat.
Page 150 Seating and safety restraints 4. Read all information and warnings on the child seat cushion and shoulder safety belt. The child seat is to be used only by children who: are at least one year old weigh between 10 and 27 kg (22 and 60 lbs.) shoulders must be below the shoulder harness slots...
Page 151 Seating and safety restraints 10. Pull the right shoulder belt fully out to put the retractor into the automatic locking mode. 11. If the belts become too tight, unbuckle the crotch safety belt buckle to unlock the retractors, then reinsert both belt tongues. Removing your child from the built-in child seat 1.
Page 152: Starting
Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Page 153 2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the parking brake is set. 4. Make sure the gearshift is in P (Park). 5. Turn the key to 3 (ON) without turning the key to 4 (START). If there is difficulty in turning the key, firmly rotate the steering wheel left and right until the key turns...
Page 154 Starting ˚F ˚C MILES/BAL L/100 km OUTSIDE TEMP INST ECONOMY AVG. ECONOMY TO EMPTY BRAKE Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. If the driver’s safety belt is fastened, the STARTING THE ENGINE 1.
Page 155 Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater-defroster system to respond quickly. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below.
Page 156 Starting Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning to bring in fresh air. Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris.
Page 157: Driving
Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 158 Driving ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the...
Page 159 The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). The parking brake is not recommended to stop a moving vehicle.
Page 160 Driving high crown in center of road high crosswinds wheels out of alignment loose or worn components in steering linkage AUTOMATIC TRANSAXLE OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) unless the brake pedal is depressed.
Page 161 Understanding gearshift positions To account for customer driving habits and conditions, your automatic transaxle electronically controls the shift feel by using an adaptive learning strategy. During the first few hundred kilometers (miles) of operation, it is normal for your transaxle to have abrupt shifts. The adaptive learning strategy is maintained by power from the battery.
Page 162 Driving automatic overdrive transaxle. When your vehicle cruises at a constant speed for any length of time, this fourth gear will increase your fuel economy. Overdrive may not be appropriate for certain terrains. If the transaxle shifts back and forth between third and fourth gears while you are driving hilly roads or if your vehicle requires additional power for climbing hills, press the O/D OFF switch.
Page 163 second and third gears and will not shift into fourth gear. Operating in D (O/D OFF) provides more engine braking than Overdrive for descending hills or city driving. To return the transaxle to the normal Overdrive operation, press the O/D OFF control again.
Page 164 Driving Driving with an automatic overdrive transaxle Your automatic transaxle electronically controls the shift feel by using an adaptive learning strategy. This feature is designed to optimize shift smoothness. It is normal for your transaxle to shift firmly during the first few hundred kilometers (miles) of operation until the adaptive strategy has been learned.
Page 165 VEHICLE LOADING Before loading a vehicle, familiarize yourself with the following terms: Base Curb Weight : Weight of the vehicle including any standard equipment, fluids, lubricants, etc. It does not include passengers or aftermarket equipment. Payload : Combined maximum allowable weight of cargo, passengers and optional equipment.
Page 166 Driving Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations. The Certification Label, found on the inside pillar of the driver’s door, lists several important vehicle weight rating limitations.
Page 167 The optional Trailer Tow Prep Package is recommended for towing of any trailer since it provides a heavy duty battery, conventional size spare tire and wiring. Trailer towing puts additional loads on your vehicle’s engine, transmission, axle, brakes, tires, and suspension. For your safety and to maximize vehicle performance, be sure to use the proper equipment while towing.
Page 168 Driving Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. Hitches For towing trailers up to 907 kg (2 000 lb), use a weight carrying hitch and ball which uniformly distributes the trailer tongue load through the underbody structure.
Page 169 Trailer lamps Trailer lamps are required on most towed vehicles. Make sure your trailer lamps conform to local and Federal regulations. See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps. Driving while you tow Do not drive faster than 88 km/h (55 mph) when towing a trailer.
Page 170 Driving LUGGAGE RACK The front and rear crossbar can be adjusted to fit the item being carried. Do not load more than 44 kg (100 lbs.) on the luggage rack. To adjust cross-bar position: 1. Loosen the thumbwheel at both ends of the cross-bar.
Page 171: Roadside Emergencies
HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. The hazard lights control is located on the instrument panel. Depress hazard lights control to activate all hazard flashers simultaneously.
Page 172: Reset Fuel Pump Shut-Off Switch
Roadside emergencies The fuel pump shut-off switch is located in the driver’s foot well, behind the kick panel. The reset button for the fuel pump shut-off switch is accessible through an opening in the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1.
Page 173: Standard Fuse Amperage Rating And Color
Standard fuse amperage rating and color Fuse Mini Standard Rating Fuses Grey Violet Pink 7.5A Brown Blue Yellow Natural Green — — — — — Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal.
Page 174 Roadside emergencies 7.5A 7.5A USE SPECIFIED FUSES ONLY The fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating Corner Lamps — I/P Illum Electron Tail Lamp Air Bag Audio Eng Cont 10A 7.5A 7.5A 15A 7.5A Description Front Exterior Lamps —...
Page 175 Fuse/Relay Fuse Amp Location Rating Room Lamp Mirror 7.5A Stop Lamp Cigar Lighter Hazard RR Pwr Plug Rear Blower Wiper Rear Blower Rear Wiper O2 Sensor 7.5A Audio 7.5A Turn Audio Amp Front Blower Eng Cont 7.5A Relays A/C Cont 7.5A Roadside emergencies Description...
Page 176: Power Distribution Box Fuses
Roadside emergencies Fuse/Relay Fuse Amp Location Rating Electron Rear Defog Front Blower Rear Defog — Heated Mirror Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.
Page 177: Fuel Pump
USE SPECIFIED FUSES OR FUSIBLE LINKS ONLY 100A MAIN The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating — FUEL PUMP ECCS — — Roadside emergencies HORN 140A JOINT CONN. RAD FAN Description — Not Used 15A* Fuel Pump Relay 10A* Powertrain Control Module...
Page 178 Roadside emergencies Fuse/Relay Fuse Amp Location Rating — H/L RH HORN — H/L LH — — — PWR WND RAD FAN LO — IGN SW — RAD FAN FR BLW RR DEF 140A** MAIN 100A** * Mini Fuses ** Maxi Fuses Description 20A* ABS Control Module...
Page 179 Relay box The relay box is located in the engine compartment in front of the battery. The relays are coded as follows: Relay location CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed.
Page 180 Roadside emergencies Temporary spare tire information Your vehicle may have a temporary or conventional size spare tire. The temporary spare tire for your vehicle is labeled as such. It is smaller than a regular tire and is designed for emergency use only. Replace this tire with a full-size tire as soon as possible.
Page 181 Roadside emergencies Removing the spare tire 1. Open the liftgate, locate the U-shaped slits in the carpet, and flip up the piece of carpet to expose the hex nut. 2. Insert the lug nut wrench on the hex nut in cargo floor. 3.
Page 182 Roadside emergencies Stowing the spare 1. Lay the tire on the ground with the interior side facing up. 2. Install the retainer through the wheel center and slide the wheel under the vehicle. 3. Turn the wrench clockwise until the tire is raised to its original position underneath the vehicle.
Page 183: Tire Change Procedure
Roadside emergencies 1. Park on a level surface, activate FUSES hazard flashers and set parking brake. 2. Place gearshift lever in P (Park), turn engine OFF, and block the diagonally opposite wheel. 3. Remove the spare tire and jack assembly. 4.
Page 184 Roadside emergencies Jacking notches are located approximately six inches rearward of the front wheels and twelve inches foward of the rear wheels. 6. Locate the jack notch closest to the tire you are changing, then place the jack on the frame rail directly behind the notch.
Page 185 JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter. Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted.
Page 186 Roadside emergencies Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Page 187 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
Page 188 Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.
Page 189 Roadside emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 190 Roadside emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment.
Page 191: Maintenance And Care
SERVICE RECOMMENDATIONS To help you service your vehicle: We highlight do-it-yourself items in the engine compartment for easy location. We provide a Scheduled Maintenance Guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.
Page 192 Maintenance and care Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel.
Page 193 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.3L V6 engine 1. Power distribution box 2. Brake fluid reservoir 3. Air filter assembly 4. Battery 5. Relay box 6. Engine oil filler cap 7. Engine oil dipstick 8. Windshield washer fluid reservoir 9.
Page 194 Maintenance and care ENGINE OIL Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervals for checking the engine oil . 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan.
Page 195 If the oil level is below the L mark, add enough oil to raise the level within the L and H range. Oil levels above the H mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7.
Page 196 Maintenance and care Engine oil and filter recommendations Look for this Certification Trademark. Use SAE 5W-30 motor oil certified for gasoline engines by the American Petroleum Institute (API). Motor oil displaying the API Certification Trademark will meet all requirements for your vehicle’s engine. Ford oil specification is WSS-M2C153-G.
Page 197 BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the Scheduled Maintenance Guide for the service interval schedules: 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir. 2.
Page 198 Maintenance and care WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way.
Page 199 The engine coolant must be maintained at the correct fluid level and concentration to work properly. If the engine coolant fluid level and concentration is not maintained correctly, damage to the engine and cooling system may result . When the engine is cold, check the level of the engine coolant in the reservoir.
Page 200 Maintenance and care DO NOT USE alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze. DO NOT USE supplemental coolant additives in your vehicle. These additives may harm your engine’s cooling system. DO NOT MIX recycled coolant and conventional coolant together in your vehicle.
Page 201 To avoid scalding hot steam or coolant from being released from the engine cooling system, never remove the radiator cap while the engine is running or hot. Failure to follow this warning may result in damage to the engine’s cooling system and possible severe personal injury.
Page 202 Maintenance and care NEVER increase the coolant concentration above 60%. Increased engine coolant concentrations above 60% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. Vehicles driven year-round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum freeze protection.
Page 203 properly, i.e., if the transaxle slips or shifts slowly or if you notice some sign of fluid leakage. Automatic transmission fluid expands when warmed. To obtain an accurate fluid check, drive the vehicle until it is warmed up (approximately 30 km [20 miles]). If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool before...
Page 204 Maintenance and care High fluid level Fluid levels above the safe range may result in transaxle failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used.
Page 205 Maintenance and care CHANGING THE AIR FILTER ELEMENT 1. Release the four clamps that secure the air filter housing cover. 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the air filter housing. 4.
Page 206 Maintenance and care If the electrolyte level in the battery is low, you can add plain tap water to the battery, as long as you do not use hard water (water with a high mineral or alkali content). If possible, however, try to only fill the battery cells with distilled water.
Page 207 transaxle must relearn its adaptive strategy. Optimal shifting will resume within a few hundred kilometers (miles) of operation. If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected.
Page 208 Maintenance and care The odor and particulate air filtration system is designed to reduce the concentration of objectionable exterior odors as well as airborne particles such as dust, spores and pollen in the air being supplied to the interior of the vehicle. The extent of EXTERIOR odor reduction depends on the odor itself and the perceptional threshold of the individual.
Page 209 2. Remove the six (6) screws (B) from the cowl grille (A) at the base of the windshield. 3. Open the hood. 4. Remove the four (4) plastic screws (C) from the forward edge of the cowl leaf screen under the hood. Remove the four (4) screw anchors by pushing upward on the screw anchor.
Page 210 Maintenance and care 8. Remove four (4) screws from the top surface of the cabin air filter top cover. 9. Remove the cover. 10. Remove the filter element by pulling forward on the top surface of the filter and lifting. 11.
Page 211 Maintenance and care 14. Position the cowl grille in place. 15. Reinstall the four (4) screw anchors and the four (4) plastic screws. 16. Close the hood. 17. Reinstall the six (6) screws in the cowl grille. 18. Reinstall the wiper arms. Ensure that you reinstall the wiper arms in the same position.
Page 212 Maintenance and care INFORMATION ABOUT TIRE QUALITY GRADES New vehicles are fitted with tires that have their Tire Quality Grade (described below) molded into the tire’s sidewall. These Tire Quality Grades are determined by standards that the United States Department of Transportation has set.
Page 213 Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 214 Maintenance and care Four tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label.
Page 215 Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer. SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle.
Page 216 Maintenance and care The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel system to work improperly in a collision, which may result in...
Page 217 Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury. Fuels can also be harmful if absorbed through the skin.
Page 218 Maintenance and care When the fuel filler door is open, the left hand sliding door will not open. When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the fuel filler cap counterclockwise, using caution to minimize the possibility of fuel spraying. 3.
Page 219 Maintenance and care Octane recommendations Your vehicle is designed to use “Regular” unleaded gasoline with an (R+M)/2 octane rating of 87. We do not recommend the use of gasolines (R+M)/2 METHOD labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly.
Page 220 Maintenance and care If you have run out of fuel: You may need to crank the engine several times after refueling before the system starts to pump the fuel from the tank to the engine. Your “Service Engine Soon” indicator may come on. For more information on the “Service Engine Soon”...
Page 221 For consistent results when filling the fuel tank: Use the same filling rate setting (low — medium — high) each time the tank is filled. Allow three automatic click-offs when filling. Always use fuel with the recommended octane rating. Use a known quality gasoline, preferably a national brand. Use the same side of the same pump and have the vehicle facing the same direction each time you fill up.
Page 222 Maintenance and care Habits Smooth, moderate operation can yield up to 10% savings in fuel. Steady speeds without stopping will usually give the best fuel economy. Idling for long periods of time (greater than one minute) may waste fuel. Anticipate stopping; slowing down may eliminate the need to stop. Sudden or hard accelerations may reduce fuel economy.
Page 223 Carrying unnecessary weight may reduce fuel economy (approximately 0.4 km/L [1 mpg] is lost for every 180 kg [400 lb] of weight carried). Adding certain accessories to your vehicle (for example bug deflectors, rollover/light bars, running boards, ski/luggage racks) may reduce fuel economy.
Page 224 Maintenance and care The scheduled maintenance items listed in the Scheduled Maintenance Guide are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 225 condition. To ready the on-board diagnostics system for I/M testing, follow the procedure described below: 1. Allow the engine to cool to ambient temperature (the engine coolant temperature gauge indicator will point to C). 2. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C).
Page 226 Maintenance and care Do not remove lamp bulbs unless they will be replaced immediately. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance. Replacing headlamp bulbs To remove the headlamp bulb: 1.
Page 227 Maintenance and care 2. Install the bulb retaining ring over the plastic base until it contacts the rear of the socket by rotating clockwise until you feel a “stop.” 3. Connect the electrical connector into the rear of the plastic base until it snaps, locking it into position.
Page 228 Maintenance and care Replacing high-mount brakelamp bulbs 1. Remove the two screws and lamp assembly from vehicle. 2. Remove the bulb by rotating socket counterclockwise and pulling it out of the lamp assembly. 3. Pull bulb straight out of socket and push in the new bulb.
Page 229 Replacing license plate lamp bulbs 1. Remove two screws, grommets and the license plate lamp assembly from the liftgate. 2. Remove bulb socket by turning counterclockwise. 3. Carefully pull the bulb from the socket and push in the new bulb. 4.
Page 230 Maintenance and care Function Stepwell lamps Glove compartment All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer. AIMING THE HEADLAMPS The alignment of your headlamps should be checked by a qualified service technician if: Oncoming motorists frequently signal you to deactivate your high beams, and your high beams are not activated.
Page 231 Maintenance and care Remove any exterior accessories, such as antennas, before entering a car wash. If you have wax applied to the vehicle at a commercial car wash, it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield.
Page 232 Maintenance and care Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: Take care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage.
Page 233 Maintenance and care Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. If necessary, use a tar remover such as Ford Extra Strength Tar and Road Oil Remover (B7A-19520–AA) or tar remover if necessary. To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners.
Page 234 Maintenance and care Cleaning the built-in child seat (if equipped) Clean with mild soap and water. Do not use household cleaning products because they may weaken the safety belt webbing or damage the vinyl parts of the seat. The child seat liner is removable and may be machine-washed and air dried. Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner.
Page 235: Motorcraft Part Numbers
MOTORCRAFT PART NUMBERS Component Engine air filter element Cabin air filter Fuel filter Battery (standard) Battery Oil filter PCV Valve Spark plugs Standard for Canada. Included with trailer tow package and rear A/C. Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information.
Page 236 Capacities and specifications LUBRICANT SPECIFICATIONS Item Ford part name Brake fluid High Performance DOT 3 Motor Vehicle Brake Fluid Door Silicone weatherstrips Lubricant Engine coolant Ford Premium Engine Coolant Engine oil Motorcraft SAE 5W-30 Super Premium Motor Door latch, hood Multi-Purpose latch,auxiliary Grease...
Page 237 Item Ford part name Disc brake Silicone Brake caliper rails Caliper Grease and Dielectric Compound Constant CV Joint Grease velocity joints (High Temp.) Windshield Ultra-clear washer fluid Windshield Washer Concentrate ENGINE DATA Engine Cubic inches Required fuel Firing order Spark plug gap Ignition system Compression ratio This ignition system meets all Canadian Interference-Causing...
Page 238 Capacities and specifications VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width (3) Overall height (with luggage rack) (4) Wheelbase (5) Track - Front (5) Track - Rear mm (in) 4 945.4 (194.7) 1 902.5 (74.9) 1 780.5 (70.1) 2 849.9 (112.2) 1 610.4 (63.4) 1 610.4 (63.4)
Page 239: Certification Label
IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’s side.
Page 240 Capacities and specifications Vehicle identification number The vehicle identification number is attached to a metal tag and is BAG II located on the driver side XXXXXXXXXXXXXXXXX instrument panel and under the liftgate scuff plate at the bottom of the liftgate opening. (Please note that in the graphic XXXX is representative of your vehicle identification number.)
Page 241: Customer Assistance
In the United States, this card is found in the Owner Guide portfolio in the glove compartment in Ford vehicles and is mailed to you if you own a Mercury or Lincoln. In Canada, it’s found in the Roadside Assistance book in the glove compartment.
Page 242 You may purchase Ford ESP from any participating Ford or Lincoln/Mercury or Ford of Canada dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs. Ford ESP also offers reimbursement benefits for towing and rental coverage.
Page 243 Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Assistance Center to find an authorized dealership to help you.
Page 244 Customer assistance If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Assistance Center to find an authorized dealership to help you. In the United States: Ford Motor Company Customer Assistance Center...
Page 245 What kinds of cases does the Board review? Unresolved warranty repair concerns or vehicle performance as designed concerns on Ford/Mercury and Lincoln cars and Ford/Mercury and Lincoln light trucks which are within the terms of any applicable written new vehicle warranty are eligible for review, except those involving:...
Page 246 Ford or Lincoln-Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln-Mercury dealership management, recognized for their business leadership qualities. What the Board needs...
Page 247 Customer assistance You will receive a letter of explanation if your application does not qualify for Board review. Oral presentations If you would like to make an oral presentation, indicate YES to question #6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made.
Page 248 Customer assistance GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact a district or owner relations/customer assistance office.
Page 249 * May be sold with the Motorcraft name A wide selection of Ford accessories are available for your vehicle through your local authorized Ford, Lincoln-Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Page 250 Customer assistance Comfort and convenience Air conditioner Air filtration systems Cargo nets Cargo organizers Cargo shades Cargo trays Dash trim Engine block heaters Gear shift knob Luggage presenter (Continental only) Manual sliding rear window Tire step Travel equipment Console Console armrest Daytime running lights Factory luggage rack Factory luggage rack adaptors...
Page 251 Customer assistance Soft luggage cover Speed control Towing mirrors Trailer hitch Trailer hitch bars and balls Trailer hitch wiring adaptor Protection and appearance equipment Air bag anti-theft locks Bed mat/bedliner tailgate covers Bed mats Bedliners Car/truck covers Cargo liners, interior Carpet floor mats Cleaners, waxes and polishes Flat splash guards...
Page 252 Customer assistance Tailgate lock Tailgate protector Tonneau covers Touch-up paint Universal floor mats For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GAWR as indicated on the Safety compliance certification label).
Page 253 Customer assistance ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio in the United States: Make checks payable to: HELM, INCORPORATED P.O. Box 07150 Detroit, Michigan 48207 For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST, for credit card holders only To order the publications in this portfolio in Canada: Make cheques payable to:...
Page 254: Reporting Safety Defects
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company.
Page 255: Index
Accessory delay ...90 Air bag supplemental restraint system ...131 and child safety seats ...133 description ...131 disposal ...135 driver air bag ...133 indicator light ...6,135 operation ...133 passenger air bag ...133 Air cleaner filter ...204,205,235 Air conditioning ...21 automatic temperature control system ...29 Air filter, cabin ...207 Anti-theft system ...104...
Page 256 Index Ford accessories for your vehicle ...248 Ford Extended Service Plan ...242 Getting assistance outside the U.S. and Canada ...248 Getting roadside assistance ...241 Getting the service you need ...243 Ordering additional owner’s literature ...253 The Dispute Settlement Board ...245 Defrost rear window ...39 Dipstick...
Page 257 GVWR (Gross Vehicle Weight Rating) ...165 calculating ...165 definition ...165 driving with a heavy load ...165 location ...165 Hazard flashers ...171 Head restraints ...110 Headlamps ...19 aiming ...230 autolamp system ...20 bulb specifications ...229 daytime running lights ...19 flash to pass ...20 high beam ...7,20 turning on and off ...19 warning chime ...11...
Page 258 Index Overdrive ...87,164 Panic alarm feature, remote entry system ...101 Parking brake ...158 Parts (see Motorcraft parts) ...235 Power distribution box (see Fuses) ...176 Power door locks ...90 Power steering ...159 fluid, checking and adding ...202 fluid, refill capacity ...235 fluid, specifications ...236,237 Radio ...40 Relays ...172,179...
Page 259 Warning chimes ...10,11 Warning lights (see Lights) ...6 Washer fluid ...198 Water, Driving through ...164 Windows power ...89 rear wiper/washer ...87 Index Windshield washer fluid and wipers ...87 checking and cleaning ...211 operation ...86 replacing wiper blades ...211 Wrecker towing ...190...
Page 264: Filling Station Information
Filling station information Item Required fuel Fuel tank capacity Engine oil capacity (includes filter change) Tire size and pressure Hood release Coolant capacity Power steering fluid capacity Automatic transmission fluid capacity Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color).

This manual is also suitable for:

1996 villager

Mercury 1999 Villager Owner's Manual

Quick Links

Related Manuals for Mercury 1999 Villager

Summary of Contents for Mercury 1999 Villager

This manual is also suitable for:

Table of Contents