Advertisement

SERVICE MANUAL
Ver. 1.0 2007.03
AUDIO POWER SPECIFICATIONS (US)
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION
With 3.2-ohm loads, both channels driven from
1 000 - 10 000 Hz; rated 3 W per channel-minimum
RMS power, with no more than 10 % total harmonic
distortion in AC operation.
Woofer with 4-ohm loads, driven from 50 - 150
Hz; rated 6 W minimum RMS power, with no more
than 10 % total harmonic distortion in AC
operation.
Other specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Emission duration: Continuous
Laser output: Less than 44.6 µW
(Th is output is the value measured at a distance
of about 200 mm from the objective lens surface
on the optical pick-up block with 7 mm
aperture.)
Number of channels
2
Frequency response
20 - 20 000 Hz +1/–2 dB
Wow and fl utter
Below measurable limit
Abbreviation
AUS
: Australian model
CND : Canadian model
E41
: AC 230V area in E model
Sony Corporation
9-887-620-01
Personal Audio Division
2007C16-1
Published by Sony Techno Create Corporation
© 2007.03
Photo : CFD-G770CPK
Model Name Using Similar Mechanism
CD
CD Mechanism Type
Section
Optical Pick-up Type
Model Name Using Similar Mechanism
TAPE
Section
Tape Transport Mechanism Type
SPECIFICATIONS
Radio section
Frequency range
FM: 87.5 - 108 MHz
AM: 530 - 1 710 kHz
(G700CP: US/G770CPK: CND, MX, E92)
AM: 531 - 1 611 kHz (G770CPK: AUS)
AM: 531 - 1 611 kHz (9 kHz step)(G770CP)
AM: 530 - 1 610 kHz (10 kHz step)(G770CP)
Antennas
FM: Telescopic antenna
AM: Built-in ferrite bar antenna
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 150 s (sec.) with Sony cassette C-60
Frequency response
TYPE I (normal): 70 - 13 000 Hz
General
Speaker
Full range: 10 cm (4 in.) dia., 3.2 Ω,
cone type (2)
Woofer: 13 cm (5 1/8 in.) dia., 4 Ω,
cone type (1)
Tweeter: 2 cm (13/16 in.) dia. (2)
E92
: AC 120V area in E model
MX
: Mexican model
SP
: Singapore model
CFD-G700CP/G770CP/
Input
Built-in audio cable with stereo-mini plug:
Minimum input level 245 mV
AUDIO IN Jack (stereo minijack):
Minimum input level 245 mV
MIC MIX (microphone) jack (monaural minijack):
Sensitivity 2.5 mV, for low impedance
microphone
Minimum input level 2.5 mV (G770CPK)
Outputs
Headphones jack (stereo minijack)
For 16 - 68 Ω impedance headphones
Power output
4 W + 4 W (at 3.2 Ω, 10% harmonic distortion)
Woofer:
12 W (at 4 Ω, 10% harmonic distortion)
Power requirements
For CD radio cassette-corder:
120 V AC, 60 Hz
(G700CP: US/G770CPK: CND, MX, E92)
230 - 240 V AC, 50 Hz (G700CP: SP)
230 V AC, 50 Hz
(G700CP: E41/G770CPK: AUS)
12 V DC, 8 R20 (size D) batteries
For remote control:
3 V DC, 2 R6 (size AA) batteries
Power consumption
AC 28 W
CD RADIO CASSETTE-CORDER
G770CPK
US Model
CFD-G700CP
Canadian Model
CFD-G770CPK
E Model
CFD-G770CP/G770CPK
Australian Model
CFD-G770CPK
CFD-G505/G555CP/G555CPK
KSM-213CDP/C2NP
KSS-213C
HCD-EC50
H21SB-C05
— Continued on next page —

Advertisement

Table of Contents
loading

Summary of Contents for Sony CFD-G700CP

  • Page 1 Woofer: 12 W (at 4 Ω, 10% harmonic distortion) System Fast winding time Compact disc digital audio system Approx. 150 s (sec.) with Sony cassette C-60 Power requirements Laser diode properties Frequency response For CD radio cassette-corder: Emission duration: Continuous...
  • Page 2 LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
  • Page 3: Table Of Contents

    7-14. Schematic Diagram 3-10. POWER Board, BATTERY Board, – MAIN (3/3), CONTROL Section – ......41 D-LIGHT Board (CFD-G700CP) ........16 7-15. Printed Wiring Boards – POWER Section – ....42 3-11. WOOFER KEY Board, CD KEY Board ......17 7-16.
  • Page 4: Servicing Notes

    CFD-G700CP/G770CP/G770CPK SECTION 1 SERVICING NOTES SAFETY CHECK-OUT This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on After correcting the original service problem, perform the following the rear exterior. safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized”...
  • Page 5: General

    CFD-G700CP/G770CP/G770CPK SECTION 2 GENERAL This section is extracted from instruction manual. CFD-G700CP (1/2) Basic Operations Notes on MP3 discs Playing a CD/MP3 disc Recording on a tape When the disc is inserted, the unit reads all the fi les on that disc.
  • Page 6: Other Operations

    CFD-G700CP/G770CP/G770CPK CFD-G700CP (2/2) Other Operations Using the display Playing tracks/MP3 fi les in random Presetting radio stations Connecting optional component order (Shuffl e Play) You can check information about the CD using the You can store radio stations into the unit’s memory. You You can enjoy the sound from an optional component display.
  • Page 7: Basic Operations

    CFD-G700CP/G770CP/G770CPK CFD-G770CP (1/2) Basic Operations Notes on MP3 discs Playing a CD/MP3 disc Recording on a tape When the disc is inserted, the unit reads all the files on that disc. During this time, “READING” is displayed. If there are many folders or non-MP3 files on the disc, it may take a long time for play to Use buttons on the unit for the operation.
  • Page 8 CFD-G700CP/G770CP/G770CPK CFD-G770CP (2/2) Other Operations Using the display Playing tracks/MP3 files in random Presetting radio stations Connecting optional component order (Shuffle Play) You can check information about the CD using the You can store radio stations into the unit’s memory. You You can enjoy the sound from an optional component display.
  • Page 9 CFD-G700CP/G770CP/G770CPK CFD-G770CPK (1/2) Basic Operations Notes on MP3 discs Playing a CD/MP3 disc Recording on a tape When the disc is inserted, the unit reads all the files on that disc. During this time, “READING” is displayed. If there are many folders or non-MP3 files on the disc, it may take a long time for play to Use buttons on the unit for the operation.
  • Page 10 CFD-G700CP/G770CP/G770CPK CFD-G770CPK (2/2) Other Operations Using the display Playing tracks/MP3 files in random Presetting radio stations Using the Karaoke function (KARAOKE order (Shuffle Play) PON) You can check information about the CD using the You can store radio stations into the unit’s memory. You display.
  • Page 11: Disassembly

    (Page 20) (Page 19) 3-7. LED BOARD 3-9. SPEAKER (10cm) 3-10. POWER BOARD, (Page 14) (Page 15) BATTERY BOARD, D-LIGHT BOARD (CFD-G700CP) (Page 16) 3-8. SPEAKER (13cm) (Page 15) 3-5. LCD BOARD, AUDIO IN BOARD, HEADPHONE BOARD, POWER KEY BOARD,...
  • Page 12: Cabinet (Upper) (1) Section

    CFD-G700CP/G770CP/G770CPK Note: Follow the disassembly procedure in the numerical order given. 3-2. CABINET (UPPER) (1) SECTION 1 Open the handle in the 4 two screws direction of the arrow. (+ BV tapping (B3) ) 6 three screws (+ BV tapping (B3) )
  • Page 13: Cabinet (Front) Section

    CFD-G700CP/G770CP/G770CPK 3-4. CABINET (FRONT) SECTION 2 six screws (+ BV tapping (B3) ) 5 cabinet (front) section 3 six screws (+ BV tapping (B3) ) 1 battery lid 3-5. LCD BOARD, AUDIO IN BOARD, HEADPHONE BOARD, POWER KEY BOARD, MICROPHONE BOARD (CFD-G770CPK), VOLUME KEY BOARD...
  • Page 14: Front Panel

    CFD-G700CP/G770CP/G770CPK 3-6. FRONT PANEL 4 front panel 1 four screws (+BV tapping(B2.6)) 2 five screws (+BV tapping(B2.6)) 3 three screws (+BV tapping(B2.6)) 3-7. LED BOARD 3 light guide ring 2 ornamental ring 4 LED 4 board 5 LED 3 board...
  • Page 15: Speaker (13Cm)

    CFD-G700CP/G770CP/G770CPK 3-8. SPEAKER (13cm) 2 speaker (13cm) 1 four screws (+BV tapping (B3)) 3-9. SPEAKER (10cm) 4 speaker (10cm) 2 two screws (+ BV tapping (B3) ) 5 two screws (+ BV tapping (B3) ) 3 two screws (+ BV tapping (B3) ) 1 Remove the solderings.
  • Page 16: Power Board, Battery Board, D-Light Board (Cfd-G700Cp)

    CFD-G700CP/G770CP/G770CPK 3-10. POWER BOARD, BATTERY BOARD, D-LIGHT BOARD (CFD-G700CP) CFD-G700CP 5 D-LIGHT board 3 two screws (+BV tapping (B3)) 1 sheet (rear) 4 two screws 8 four screws (+BV tapping (B3)) (+BV tapping (B3)) 0 POWER board qa transformer bracket...
  • Page 17: Woofer Key Board, Cd Key Board

    CFD-G700CP/G770CP/G770CPK 3-11. WOOFER KEY BOARD, CD KEY BOARD 1 CNP805 (3P) 2 four screws (+ BV tapping (B2.6) ) 8 button (CD) 6 four screws (+ BV tapping (B2.6) ) 7 CD KEY board 4 WOOFER KEY board 3 CNP401 (2P) 5 button (SOUND) 3-12.
  • Page 18: Tape Mechanism Deck

    CFD-G700CP/G770CP/G770CPK 3-13. TAPE MECHANISM DECK 1 three screws (+ BV tapping (B3) ) 3 CNP303 (6 core) 4 tape mechanism deck 2 CN303 (11 core) 3-14. MAIN BOARD 6 three screws (+BV tapping(B3)) 1 CNP1 (11 core) 8 MAIN board...
  • Page 19: Cd Block Section

    CFD-G700CP/G770CP/G770CPK 3-15. CD BLOCK SECTION 1 four screws (+ PWH tapping (B2.6) ) 2 flexible flat cable CN201 (21 core) 3 CD block section 3-16. OPTICAL PICK-UP (KSM-213CDP/C2NP) 2 CD cover 1 two hooks...
  • Page 20: Tc Board

    CFD-G700CP/G770CP/G770CPK 3-17. TC BOARD 1 screw 4 TC board 3 Remove soldering from the four points. yellow red white black TC board 2 hook 3-18. MAIN BELT, SUB BELT 1 two screws ( +BIND DT M2 × 6) 3 motor assy...
  • Page 21: Test Mode

    CFD-G700CP/G770CP/G770CPK SECTION 4 TEST MODE [MC COLD RESET] [CD SERVICE MODE] The cold reset clears all data including preset data stored in the This mode can move the SLED of the optical pick-up, and also can memory to initial conditions. Execute this mode when returning turn the optical pick-up laser power on and off.
  • Page 22 CFD-G700CP/G770CP/G770CPK Contents of “BD Errors” Error display example D 0 02 09 01 1 2 3 4 1 It indicates the error history number 0 to 4: The error code number 0 indicates the newest error. 2 It indicates the error content 01: The focus servo cannot lock-in.
  • Page 23: Mechanical Adjustments

    CFD-G700CP/G770CP/G770CPK SECTION 5 SECTION 6 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS • Precaution CD SECTION 1. Clean the following parts with a denatured-alcohol-moistened swab : Note: record/playback head pinch roller 1. CD Block is basically constructed to operate without adjustment. erase head rubber belts 2.
  • Page 24 CFD-G700CP/G770CP/G770CPK Adjustment Location: Record/Playback/Erase Head 0 dB=0.775 V TAPE SECTION 1. Demagnetize the record/playback head with a head demagnetizer. 2. Do not use a magnetized screwdriver for the adjustments. • Test Tape Tape Signal Used for P-4-A063 6.3 kHz, –10 dB...
  • Page 25 CFD-G700CP/G770CP/G770CPK 0 dB = 1 µV AM IF ADJUSTMENT TUNER SECTION Adjust for a maximum reading on level meter. • AM Section Setting: 450 kHz RADIO BAND•AUTO PRESET button: AM AM FREQUENCY COVERAGE ADJUSTMENT (SP, E41, AUS) Put the loop...
  • Page 26 CFD-G700CP/G770CP/G770CPK Adjustment Location: L3,CT3 AM TRACKING ADJUSTMENT L1,CT1 – TUNER BOARD (Component Side) – FM TRACKNG ADJUSTMENT TP-ANT (JW2) AM IF ADJUSTMENT FM IF ADJUSTMENT FM FREQUENCY AM FREQUENCY COVERAGE COVERAGE ADJUSTMENT ADJUSTMENT – TUNER BOARD (Conductor Side) – (GND)
  • Page 27: Diagrams

    MICROPHONE board D-LIGHT board – Other Boards – (CFD-G770CPK only) (CFD-G700CP only) no mark : CD PLAY • Voltages are taken with a VOM (Input impedance 10 MΩ). These are omitted. Voltage variations may be noted due to normal production POWER KEY board tolerances.
  • Page 28: Block Diagram - Tuner/Cd Section

    CFD-G700CP/G770CP/G770CPK 7-1. BLOCK DIAGRAM – TUNER/CD SECTION – ANT1 RADIO 6V TELESCOPIC ANTENNA FM/AM FRONT-END FM IF IF AMP,DET,FM MPX QUAD VCC1 VCC2 FM RF IN MIX OUT FM IF-IN RADIO 6V MPX-IN TU-L MAIN FM/AM DET OUT SECTION MUTE...
  • Page 29: Block Diagram - Main Section

    CFD-G700CP/G770CP/G770CPK 7-2. BLOCK DIAGRAM – MAIN SECTION – G770CPK IC401 MIC MIX AMP VDD(SW) J401 • R-CH is omitted due to same as L-CH. Q401,402 Q405 D401 MIC MIX MIC AMP BUFFER • Signal Path S422 R-CH KARAOKE RV401 : FM...
  • Page 30: Printed Wiring Board - Bd90 Board

    CFD-G700CP/G770CP/G770CPK 7-3. PRINTED WIRING BOARD – BD90 BOARD – • :Uses unleaded solder. • See page 27 for Circuit Boards Location. BD90 BOARD (SIDE B) BD90 BOARD (SIDE A) M401 (SPINDLE) S201 (LIMIT) C403 C404 R402 M402 (SLED) C122 IC401...
  • Page 31: Schematic Diagram - Bd90 Board

    CFD-G700CP/G770CP/G770CPK • See page 44 for Waveforms. • See page 44 for IC Block Diagrams. • See page 46 for IC Pin Function Description. 7-4. SCHEMATIC DIAGRAM – BD90 BOARD – R127 C107 C136 R126 R125 R142 R139 R129 Q301...
  • Page 32: Printed Wiring Board - Tuner Board

    CFD-G700CP/G770CP/G770CPK 7-5. PRINTED WIRING BOARD – TUNER BOARD – • :Uses unleaded solder. • See page 27 for Circuit Boards Location. US,CND, MX,E92 (CV) SP,E41,AUS MAIN BOARD (Page 36) US,CND, MX,E92 (GND) SP,E41,AUS 1-863-438- (11) • Semiconductor Location Ref. No.
  • Page 33: Schematic Diagram - Tuner Board

    CFD-G700CP/G770CP/G770CPK 7-6. SCHEMATIC DIAGRAM – TUNER BOARD – • See page 44 for Waveforms. • See page 45 for IC Block Diagrams. JC12 JC11 IC B/D US,CND, MX,E92 SP,E41,AUS JC24 US,CND,MX,E92 CNP1 ANT1 IC B/D JC33 (Page 40) JC34 JC13...
  • Page 34: Printed Wiring Board - Tc Board

    CFD-G700CP/G770CP/G770CPK 7-7. PRINTED WIRING BOARD – TC BOARD – • See page 27 for Circuit Boards Location. • :Uses unleaded solder. T301 C307 C305 R307 C304 R308 R306 C306 JC304 IC301 CN303 R302 R202 R206 R303 S301 S301 (REC/PB) C302...
  • Page 35: Schematic Diagram - Tc Board

    CFD-G700CP/G770CP/G770CPK 7-8. SCHEMATIC DIAGRAM – TC BOARD – • See page 44 for Waveforms. • See page 45 for IC Block Diagram. IC301 (5,HZ) R103 R112 IC B/D R301 C102 R102 C103 R104 R111 TAPE MECHANISM DECK (1/2) C301 C104...
  • Page 36: Printed Wiring Board - Main Board

    CFD-G700CP/G770CP/G770CPK 7-9. PRINTED WIRING BOARD – MAIN BOARD – • See page 27 for Circuit Boards Location. • :Uses unleaded solder. POWER KEY VOLUME KEY BOARD BOARD BOARD BOARD CN802 CN801 KH407 KH405 (Page 38) (Page 38) (Page 38) (Page 38)
  • Page 37: Printed Wiring Boards - Audio Section

    CFD-G700CP/G770CP/G770CPK 7-10. PRINTED WIRING BOARDS – AUDIO SECTION – • See page 27 for Circuit Boards Location. • :Uses unleaded solder. J401 MIC MIX KH356 C408 L307 L303 KARAOKE RV401 MAIN MIC LEVEL D401 BOARD KARAOKE CNP397 R426 (Page 36)
  • Page 38: Printed Wiring Boards - Control Section

    CFD-G700CP/G770CP/G770CPK 7-11. PRINTED WIRING BOARDS – CONTROL SECTION – • See page 27 for Circuit Boards Location. • :Uses unleaded solder. MAIN BOARD • Semiconductor MAIN BOARD CNP806 Location CNP803 (Page 36) Ref. No. Location (Page 36) D403 D404 D405...
  • Page 39: Schematic Diagram - Main (1/3), Audio Section

    CFD-G700CP/G770CP/G770CPK 7-12. SCHEMATIC DIAGRAM – MAIN (1/3), AUDIO SECTION – • See page 44 for IC Block Diagram. CNP2 CNP357 R122 CNP394 R104 R121 4.7k L102 L101 L202 J402 R221 R204 KH355 AUDIO IN JACK 4.7k R222 IC351 BA5417 R103...
  • Page 40: Schematic Diagram - Main Section (2/3)

    CFD-G700CP/G770CP/G770CPK 7-13. SCHEMATIC DIAGRAM – MAIN SECTION (2/3) – • See page 44 for Waveform. • See page 45 for IC Block Diagram. • See page 49 for IC Pin Function Description. L158 CNP807 C411 100p CN804 R901 C841 C839...
  • Page 41: Schematic Diagram - Main (3/3), Control Section

    CFD-G700CP/G770CP/G770CPK 7-14. SCHEMATIC DIAGRAM – MAIN (3/3), CONTROL SECTION – • See page 44 for IC Block Diagram. R418 R419 R494 R489 Q407 RT1N144C-TP-1 D414 1SS355WTE-17 Q406 RT1N144C-TP-1 D415 IC891 MC2836-T112-1 RPM7140-V4 R469 C401 R428 100k C425 C254 C426 R447...
  • Page 42: Printed Wiring Boards - Power Section

    CFD-G700CP/G770CP/G770CPK 7-15. PRINTED WIRING BOARDS – POWER SECTION – • See page 27 for Circuit Boards Location. • :Uses unleaded solder. • Semiconductor MAIN BOARD Location CNP301 (Page 36) Ref. No. Location D901 D902 D903 D904 C909 J901 ~AC IN...
  • Page 43: Schematic Diagram - Power Section

    CFD-G700CP/G770CP/G770CPK 7-16. SCHEMATIC DIAGRAM – POWER SECTION – KH903 C909 KH902 CNP941 T901 2200 J901 FH901 FH902 POWER HOLDER FUSE HOLDER FUSE TRANSFORMER C901 0.022 D901 1N5401-C352 F902 D902 1N5401-C352 JW944 FUSS GLASS TUBE JW943 C902 0.022 C927 JW941 C903 0.022...
  • Page 44 CFD-G700CP/G770CP/G770CPK • IC Block Diagrams • Waveforms – BD90 Board – – TUNER Board – – MAIN Board – – BD90 Board – IC201 TK63115SCL-G@GT IC401 BA5826SFP-E2 IC101 ia (RFi) IC2 w; (XOUT) IC801 os (X1) (CD PLAY mode) VIN 1...
  • Page 45 CFD-G700CP/G770CP/G770CPK – MAIN Board – – TC Board – IC301 TA2068N (5, HZ) IC805 S-80828CNMC-B8NT2G LINE L.LIN L.PO MIC I/EX AMP1 TAPE BUF AMP L.NF RADIO L.RAD AMP1 L.RO VREF MONITOR 26dB BUF AMP MUTE L.IN L.LO LOGIC BUF AMP R.LO...
  • Page 46 CFD-G700CP/G770CP/G770CPK • IC Pin Function Description BD90 BOARD IC101 TC94A70FG-006 (RF AMP, DSP, MP3) Pin No. Pin Name Description AVSS3 — Ground terminal (Used CD analog 3.3V) RFZi RF ripple zero cross signal input terminal RFRP RF ripple signal output terminal (Used zero cross)
  • Page 47 CFD-G700CP/G770CP/G770CPK Pin No. Pin Name Description Pio0 REQ output terminal Pio1 Not used (Open) Pio2 Not used (Open) Pio3 Not used (Open) VSS1 — Ground terminal (Digital 3.3V) VDDT3 — Power supply terminal (Digital I/O 3.3V) SBSY Sub code block sync output terminal...
  • Page 48 CFD-G700CP/G770CP/G770CPK Pin No. Pin Name Description FPi1(B) Main beam input terminal (Connect to pin diode B) TPi(F) Sub beam AMP input terminal (Connect to pin diode F) TNPC Capacitor connect terminal to the middle pointof TNI/TPI input register TNi(E) Sub beam AMP input terminal (Connect to pin diode E)
  • Page 49 CFD-G700CP/G770CP/G770CPK MAIN BOARD IC801 MB90802NPF-G-127E1 (SYSTEM CONTROLLER) Pin No. Pin Name Description CLK-SHIFT_AM Clock shift signal output for AM radio CLK-SHIFT_FM Clock shift signal output for FM radio I-MP3-REQ Request signal input from CD-DSP-MP3 decorder (IC101) O-MP3-M-MUTE Mute signal output to Spindle and Sleding motor driver (IC401)
  • Page 50 CFD-G700CP/G770CP/G770CPK Pin No. Pin Name Description RSTX System reset signal input O-CD-SW Pre-amp select signal output O-CD CD+3.3V regulator control signal output O-TAPE Pre-amp select signal output VLCD LCD power setting input 59 to 62 COM1-4 Common signal output to the LCD...
  • Page 51: Exploded Views

    CFD-G700CP/G770CP/G770CPK SECTION 8 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • The mechanical parts with no reference The components identified by mark 0 or may have some difference from the original number in the exploded views are not supplied.
  • Page 52: Cabinet (Front) Section

    CFD-G700CP/G770CP/G770CPK 8-2. CABINET (FRONT) SECTION G770CPK supplied supplied SP393 D404 D409 D403 D410 D411 D407 D405 D408 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-2177-000-1 PANEL, (FRONT) SUB ASSY 2-895-594-01 CAP, SWITCH (G770CPK) 2-895-583-01 COVER, PANEL...
  • Page 53: Cabinet (Rear) Section

    CFD-G700CP/G770CP/G770CPK 8-3. CABINET (REAR) SECTION G700CP J901 T901 F902 supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-254-143-11 SCREW (B3), (+) BV TAPPING 2-067-415-01 TERMINAL (+, –), BATTERY 2-895-581-01 HOLDER, TRANSFORMER (G770CP/G770CPK) 2-895-597-01 TERMINAL (–), BATTERY...
  • Page 54: Cabinet (Upper) Section-1

    CFD-G700CP/G770CP/G770CPK 8-4. CABINET (UPPER) SECTION-1 S201 supplied tape mechanism deck section supplied cabinet (upper) section-2 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-108-743-01 CUSHION KEY CASSETTE 1-832-613-21 CABLE, FLEXIBLE FLAT (21 CORE) 2-895-588-01 BUTTON, REC...
  • Page 55: Cabinet (Upper) Section-2

    CFD-G700CP/G770CP/G770CPK 8-5. CABINET (UPPER) SECTION-2 supplied supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-895-568-01 PANEL (UPPER) (G770CP/G770CPK) 3-047-468-21 DAMPER 2-895-568-11 PANEL (UPPER) (G700CP) 2-895-060-01 SPRING, CASSETTE 2-895-586-01 BUTTON, CD 2-895-572-01 LID, CASSETTE (G770CPK) A-1244-299-A CD KEY BOARD, COMPLETE 2-895-572-11 LID, CASSETTE (G700CP) 3-252-827-01 SCREW (B2.6), (+) BV TAPPING...
  • Page 56: Tape Mechanism Deck Section

    CFD-G700CP/G770CP/G770CPK 8-6. TAPE MECHANISM DECK SECTION supplied supplied supplied supplied supplied supplied supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-670-389-01 BELT (1) A-1246-280-A TC BOARD, COMPLETE 2-670-390-01 BELT (2) 2-659-455-01 HOLDER (REC) 1-797-375-11 DECK, MECHANICAL (H21SB-C05)
  • Page 57: Electrical Parts List

    CFD-G700CP/G770CP/G770CPK SECTION 9 AUDIO IN BATTERY ELECTRICAL PARTS LIST BD90 NOTE: • Due to standardization, replacements in the • RESISTORS When indicating parts by reference number, parts list may be different from the parts All resistors are in ohms. please include the board name.
  • Page 58 CFD-G700CP/G770CP/G770CPK BD90 CD KEY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C202 1-128-995-21 ELECT CHIP 100uF R146 1-216-864-11 SHORT CHIP C204 1-164-360-11 CERAMIC CHIP 0.1uF R147 1-216-864-11 SHORT CHIP C205 1-164-360-11 CERAMIC CHIP 0.1uF R148...
  • Page 59 CFD-G700CP/G770CP/G770CPK CD KEY D-LIGHT HEADPHONE LED1 LED2 LED3 LED4 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < SWITCH > < LIQUID CRYSTAL DISPLAY > S401 1-786-050-21 SWITCH, KEY BOARD (TUNE –/ –) LCD401 1-802-396-11 DISPLAY PANEL, LIQUID CRYSTAL...
  • Page 60 CFD-G700CP/G770CP/G770CPK MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C123 1-126-961-11 ELECT 2.2uF C326 1-165-176-11 CERAMIC CHIP 0.047uF C124 1-162-927-11 CERAMIC CHIP 100PF C327 1-164-227-11 CERAMIC CHIP 0.022uF C125 1-126-963-11 ELECT 4.7uF C332 1-126-960-11 ELECT...
  • Page 61 CFD-G700CP/G770CP/G770CPK MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C423 1-104-662-91 ELECT 22uF C851 1-162-927-11 CERAMIC CHIP 100PF (G770CPK) C852 1-162-927-11 CERAMIC CHIP 100PF C424 1-126-964-11 ELECT 10uF C853 1-162-927-11 CERAMIC CHIP 100PF (G770CPK) C425 1-127-715-91 CERAMIC CHIP 0.22uF...
  • Page 62 CFD-G700CP/G770CP/G770CPK MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < FERRITE BEAD > L159 1-410-501-11 INDUCTOR 2.2uH L160 1-410-501-11 INDUCTOR 2.2uH FB831 1-216-864-11 SHORT CHIP L803 1-414-743-21 INDUCTOR 47uH FB832 1-216-864-11 SHORT CHIP FB833 1-216-864-11 SHORT CHIP <...
  • Page 63 CFD-G700CP/G770CP/G770CPK MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R129 1-216-864-11 SHORT CHIP R325 1-216-825-11 METAL CHIP 2.2K 1/10W R130 1-216-841-11 METAL CHIP 1/10W R326 1-216-821-11 METAL CHIP 1/10W R135 1-216-864-11 SHORT CHIP R151 1-216-833-11 METAL CHIP...
  • Page 64 CFD-G700CP/G770CP/G770CPK MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R435 1-216-829-11 METAL CHIP 4.7K 1/10W R807 1-216-829-11 METAL CHIP 4.7K 1/10W (G770CPK) R808 1-216-821-11 METAL CHIP 1/10W R436 1-216-825-11 METAL CHIP 2.2K 1/10W R809 1-216-821-11 METAL CHIP...
  • Page 65 CFD-G700CP/G770CP/G770CPK MAIN MICROPHONE Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R860 1-216-833-11 METAL CHIP 1/10W R946 1-216-825-11 METAL CHIP 2.2K 1/10W R861 1-216-833-11 METAL CHIP 1/10W R947 1-216-825-11 METAL CHIP 2.2K 1/10W R862 1-216-833-11 METAL CHIP...
  • Page 66 CFD-G700CP/G770CP/G770CPK POWER POWER KEY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1243-633-A POWER BOARD, COMPLETE C305 1-162-962-11 CERAMIC CHIP 470PF (US, CND, MX, E92) C306 1-162-970-11 CERAMIC CHIP 0.01uF A-1244-369-A POWER BOARD, COMPLETE (SP, E41, AUS)
  • Page 67 CFD-G700CP/G770CP/G770CPK TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSFORMER > 1-162-927-11 CERAMIC CHIP 100PF 1-162-964-11 CERAMIC CHIP 0.001uF T301 1-416-041-11 TRANSFORMER, BIAS OSCILLATION 1-162-927-11 CERAMIC CHIP 100PF ************************************************************* 1-162-927-11 CERAMIC CHIP 100PF A-1244-418-A TUNER BOARD, COMPLETE...
  • Page 68 CFD-G700CP/G770CP/G770CPK TUNER VOLUME KEY WOOFER KEY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-410-509-11 INDUCTOR 10uH R458 1-216-809-11 METAL CHIP 1/10W < RESISTOR > < SWITCH > 1-216-817-11 METAL CHIP 1/10W S404 1-786-050-21 SWITCH, KEY BOARD (MODE)
  • Page 69 CFD-G700CP/G770CP/G770CPK Ref. No. Part No. Description Remark 0 J901 1-526-838-11 INLET, AC 2P (- AC IN) (SP, E41, AUS) 0 J901 1-540-009-11 INLET, AC (- AC IN) (US, CND, MX, E92) S201 1-771-853-11 SWITCH, DETECTION (LIMIT) SP191 1-826-684-11 SPEAKER (10cm)
  • Page 70: Revision History

    CFD-G700CP/G770CP/G770CPK REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...

This manual is also suitable for:

Cfd-g770cpkCfd-g770cp

Table of Contents