Sony CFD-G500 Service Manual
Hide thumbs
Also See for CFD-G500:
- Operating instructions (2 pages) ,
- Specifications (2 pages) ,
- Limited warranty (1 page)
Table of Contents
Advertisement
Quick Links
CFD-G500/G500L
SERVICE MANUAL
Ver. 1.4 2005.10
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance
of about 200 mm from the objective lens surface
on the optical pick-up block with 7 mm
aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm)
(CLV)
Number of channels
2
Frequency response
20 - 20 000 Hz +1/–2 dB
Wow and flutter
Below measurable limit
Radio section
Frequency range
CFD-G500
FM
87.5 - 108 MHz
AM
531 - 1 611 kHz
CFD-G500L
FM
87.5 - 108 MHz
MW
531 - 1 611 kHz (9 kHz step)
530 - 1 610 kHz (10 kHz step)
LW
153 - 279 kHz
Sony Corporation
9-877-730-05
Personal Audio Division
2005J16-1
Published by Sony Engineering Corporation
© 2005.10
Photo : CFD-G500
Model Name Using Similar Mechanism
CD
CD Mechanism Type
Section
Optical Pick-up Type
Model Name Using Similar Mechanism
TAPE
Section
Tape Transport Mechanism Type
SPECIFICATIONS
IF
FM: 10.7 MHz
AM/MW/LW: 450 kHz
Aerials
FM: Telescopic aerial
AM/MW/LW: Built-in ferrite bar aerial
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 120 s (sec.) with Sony cassette C-60
Frequency response
TYPE I (normal): 70 - 13 000 Hz
General
Speaker
Full range: 10 cm dia., 3.2 Ω, cone type (2)
Woofer: 10 cm dia., 4 Ω, cone type (1)
Input
LINE IN jack (stereo minijack):
Minimum input level 330 mV
Output
Headphones jack (stereo minijack)
For 16 - 68 Ω impedance headphones
Maximum power output
Full range: 8 W
Woofer: 12 W
Power requirements
For CD radio cassette-corder:
230V AC, 50 Hz
12 V DC, 8 R20 (size D) batteries
For remote control:
3 V DC, 2 R03 (size AAA) batteries
CD RADIO CASSETTE-CORDER
US Model
Canadian Model
E Model
Australian Model
AEP Model
CFD-G500/G500L
UK Model
CFD-S250L
KSM-213RDP/KSM-213CDP
KSS-213R/KSS-213C
CFD-S250L
MF-G500
Power consumption
AC 30 W
Battery life
For CD radio cassette-corder:
FM recording
Sony R20P: approx. 6 h
Sony alkaline LR20: approx. 18 h
Tape playback
Sony R20P: approx. 1.5 h
Sony alkaline LR20: approx. 6 h
CD playback
Sony R20P: approx. 1 h
Sony alkaline LR20: approx. 4 h
Dimensions
Approx. 530 × 327 × 241 mm (w/h/d)
(incl. projecting parts)
Mass
Approx. 8 kg (incl. batteries)
Supplied accessory
Mains lead (1)
Remote control (1)
Design and specifications are subject to change
without notice.
CFD-G500
CFD-G500L
Advertisement
Table of Contents
Related Manuals for Sony CFD-G500
Summary of Contents for Sony CFD-G500
-
Page 1: Specifications
Sony R20P: approx. 1.5 h on the optical pick-up block with 7 mm Fast winding time aperture.) Sony alkaline LR20: approx. 6 h Approx. 120 s (sec.) with Sony cassette C-60 Spindle speed CD playback Frequency response 200 r/min (rpm) to 500 r/min (rpm) TYPE I (normal): 70 - 13 000 Hz Sony R20P: approx. -
Page 2: Table Of Contents
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY. -
Page 3: Table Of Contents 1. Servicing Notes
CFD-G500/G500L SECTION 1 SERVICING NOTES SAFETY CHECK-OUT NOTES ON HANDLING THE OPTICAL PICK-UP After correcting the original service problem, perform the following BLOCK OR BASE UNIT safety checks before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, The laser diode in the optical pick-up block may suffer electrostatic and all other exposed metal parts for AC leakage. -
Page 4: General
CFD-G500/G500L SECTION 2 This section is extracted from instruction manual. GENERAL Location of controls Remote Control Inserting a cassette Loading a CD With the side you want to SLEEP play facing upward OPERATE FUNCTION (POWER) Number buttons With the labeled side up... -
Page 5: Disassembly
CFD-G500/G500L SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. CABINET (UPPER) SECTION-1 (Page 5) 3-2. CABINET (UPPER) SECTION-2 (Page 6) 3-8. H/P BOARD 3-3. CABINET (FRONT) SECTION 3-7. CONTROL 1 BOARD 3-11. TAPE MECHANISM... -
Page 6: Cabinet (Upper) Section-2
CFD-G500/G500L 3-2. CABINET (UPPER) SECTION-2 0 connector (5p) (CNP301) 8 connector (4p) (CNP392) handle 7 connector (2p) (CNP806) 9 connector 6 flexible flat cable (4p) (CNP393) (27 core) (CNP801) Close the cassette lid. Remove the upper section in the direction of the arrow. -
Page 7: Control 2 Board, Control 3 Board
CFD-G500/G500L 3-4. CONTROL 2 BOARD, CONTROL 3 BOARD 2 function button three screws (BVTP 2.6 × 10) two screws (BVTP 2.6 × 10) 6 volume button 4 CONTROL 2 board 8 CONTROL 3 board three screws (BVTP 2.6 × 8) four screws (BVTP 2.6 ×... -
Page 8: Power Board, Trans Board
CFD-G500/G500L 3-6. POWER BOARD, TRANS BOARD Remove the harnesses in the direction of the arrow. 2 connector (4p) (CNP902) two screws (BVTP 3 × 10) Remove the harnesses in the direction of the arrow. screws (BVTP 3 × 10) 4 BAT... -
Page 9: H/P Board, Tuner Board
CFD-G500/G500L 3-8. H/P BOARD, TUNER BOARD Remove the soldering two screws screws (BVTP 3 × 10) (PWH 2.6 × 10) 8 JACK HOLD board 9 H/P board TUNER board 2 connector (11p) (CNP1) 6 connector (9p) (CNP391) 5 connector (3p) (CNP394) 3-9. -
Page 10: Cd Block Section
CFD-G500/G500L 3-10. CD BLOCK SECTION four screws (PWH 2.6 × 10) CD block section 3-11. TAPE MECHANISM DECK 1 connector three screws (6p) (CNP303) (BVTP 3 × 10) 5 tape mechanism deck 2 flexible flat cable (CNP805) Open the cassette lid. -
Page 11: Tc Board
CFD-G500/G500L 3-12. TC BOARD 1 screw 4 TC board Remove soldering from the four points. yellow red gray black TC board 2 hook 3-13. MAIN BELT, SUB BELT 1 two screws (+bind DT M2 × 6) 3 pulley motor section... -
Page 12: Mechanical Adjustments
CFD-G500/G500L SECTION 4 SECTION 5 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS PRECAUTION TAPE SECTION 0 dB = 0.775 V 1. Clean the following parts with a denatured-alcohol-moistened swab : • Standard Output Level record/playback head pinch roller Output terminal HP OUT erase head rubber belts 32 Ω... - Page 13 CFD-G500/G500L AEP, UK, East European, Russian Models TUNER SECTION 0 dB = 1 µV MW IF ADJUSTMENT • AM Section Adjust for a maximum reading on level meter. Setting: RADIO BAND•AUTO PRESET button: AM, MW or LW 450 kHz AM RF signal...
- Page 14 CFD-G500/G500L Adjustment Location: – MAIN board (component side) – L3-2 L3-1 TP (VT) TP (FM IN) (CONDUCTOR SIDE) (CONDUCTOR SIDE) CD SECTION CD section adjustments are done automatically in this set. In case of operation check, confirm that focus bias.
-
Page 15: Diagrams
CFD-G500/G500L SECTION 6 DIAGRAMS • Circuit Boards Location THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For Printed Wiring Boards. For Schematic Diagrams. Note: Note: •... -
Page 16: Block Diagrams - Main Section
CFD-G500/G500L 6-1. BLOCK DIAGRAMS — MAIN SECTION — L OUT TUNER/CD SECTION IC301 PRE AMP L.L IN IC371 L-CH TUNER/CD RADIO IC321 POWER AMP SECTION BUFFER SOUND/VOLUME TAPE L.LD R-CH J391 VIN1 OUT1 TAPE STBY Q171 MUTE R-CH SEL1 VDD(SW) -
Page 17: Tuner/Cd Section
CFD-G500/G500L — TUNER/CD SECTION — ANT1 RADIO 6V TELESCOPIC ANTENNA FM IF FRONT-END IF AMP,DET,FM MPX VCC1 VCC2 QUAD MIX OUT FM RF IN FM IF-IN RADIO 6V MPX-IN L-CH MAIN FM/AM DET OUT SECTION MUTE BUFFER R-CH FM RF OUT... -
Page 18: Printed Wiring Board - Cd Section
CFD-G500/G500L 6-2. PRINTED WIRING BOARD — CD SECTION — • Refer to page 15 for Circuit Boards Location. JC702 • Semiconductor Location JC701 Ref. No. Location R742 IC701 IC702 IC702 Q701 M701 JW718 JW719 C741 JW715 JW721 JW720 S701 C740... -
Page 19: Schematic Diagram - Cd Section
CFD-G500/G500L 6-3. SCHEMATIC DIAGRAM — CD SECTION — • Refer to page 32 for IC Block Diagrams. C727 C726 C724 C725 C721 R717 C730 C720 R716 R728 R727 C722 R718 C723 R721 (Page 27) C746 C745 C755 C754 C744 C747... -
Page 20: Printed Wiring Board - Tuner Section (Aep, Uk, Cet Model)
CFD-G500/G500L 6-4. PRINTED WIRING BOARD — TUNER SECTION (AEP, UK, CET MODEL) — • Refer to page 15 for Circuit Boards Location. (AEP,UK,CET MODEL) KH801 (Page 26) KH802 (Page 26) 1-688-455- (11) • Semiconductor Location Ref. No. Location C-10 B-12... -
Page 21: Schematic Diagram - Tuner Section (Aep, Uk, Cet Model)
CFD-G500/G500L 6-5. SCHEMATIC DIAGRAM — TUNER SECTION (AEP, UK, CET MODEL) — • Refer to page 32 for IC Block Diagrams. (AEP,UK,CET MODEL) JC22 IC B/D JC24 IC B/D JC23 ANT1 CNP2 CNP1 KH802 (Page 27) JC33 KH801 (Page 27) JC34 •... -
Page 22: Printed Wiring Board - Tuner Section (Us, Cnd, E, Sp, Aus Model)
CFD-G500/G500L 6-6. PRINTED WIRING BOARD — TUNER SECTION (US, CND, E, SP, AUS MODEL) — • Refer to page 15 for Circuit Boards Location. TUNER BOARD (US,CND,E,SP,AUS MODEL) KH801 (Page 26) KH802 (Page 26) 1-688-455- (11) • Semiconductor Location Ref. No. -
Page 23: Schematic Diagram - Tuner Section (Us, Cnd, E, Sp, Aus Model)
CFD-G500/G500L 6-7. SCHEMATIC DIAGRAM — TUNER SECTION (US, CND, E, SP, AUS MODEL) — • Refer to page 32 for IC Block Diagrams. (US,CND,E,SP,AUS MODEL) JC12 JC11 C51 C52 JC24 IC B/D IC B/D JC13 ANT1 CNP2 CNP1 KH802 (Page 27) -
Page 24: Printed Wiring Board - Tc Section
CFD-G500/G500L 6-8. PRINTED WIRING BOARD — TC SECTION — • Refer to page 15 for Circuit Boards Location. • Semiconductor Location Ref. No. Location T301 C308 AEP,UK,CET IC301 C307 Q301 C310 Q302 C305 R307 Q303 R308 C304 R306 C306 CN303... -
Page 25: Schematic Diagram - Tc Section
CFD-G500/G500L 6-9. SCHEMATIC DIAGRAM — TC SECTION — • Refer to page 33 for IC Block Diagram. IC301 IC B/D R103 R112 R301 C102 R102 C103 R104 R111 C301 C104 C101 JC302 HRP301 C107 R110 C105 JC306 JC305 R101 C303... -
Page 26: Printed Wiring Board - Main Section
CFD-G500/G500L 6-10. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 15 for Circuit Boards Location. CONTROL 1 CONTROL 2 BOARD BOARD BOARD CN401 CN801 CNP403 (Page 29) (Page 29) (Page 29) • Semiconductor Location S801 Ref. No. -
Page 27: Schematic Diagram - Main Section (1/2)
CFD-G500/G500L 6-11. SCHEMATIC DIAGRAM — MAIN SECTION (1/2) — • Refer to page 34 for IC PIN FUNCTION DESCRIPTION. IC891 RPM7140-V4 LCD891 C891 0.022 CN801 CNP801 R416 R417 R418 R419 R420 2.2k 4.7k 2.2k S416 S414 S415 R869 Q810 R836... -
Page 28: Schematic Diagram - Main Section (2/2)
CFD-G500/G500L 6-12. SCHEMATIC DIAGRAM — MAIN SECTION (2/2) — • Refer to page 33 for IC Block Diagram. R121 R364 R365 Q351 KH355 CNP394 KTC3198GR-AT C360 IC351 BA5417 J381 D352 1SS355TE-17 R363 R125 R221 R225 R362 1.2k R122 4.7k 4.7k... -
Page 29: Printed Wiring Board - Lcd Section
CFD-G500/G500L 6-13. PRINTED WIRING BOARD — LCD SECTION — • Refer to page 15 for Circuit Boards Location. AMS- POWER SLEEP LINE CN401 AMS+ WOOFER MAIN BOARD CNP804 (Page 26) VOL - MAIN BOARD CNP801 (Page 26) RADIO BAND CN801... -
Page 30: Printed Wiring Board - Power Section
CFD-G500/G500L 6-14. PRINTED WIRING BOARD — POWER SECTION — • Refer to page 15 for Circuit Boards Location. CNP301 (Page 26) T901 POWER TRANSFORMER NOT REPLACEABLE BUILT IN TRANSFORMER... -
Page 31: Schematic Diagram - Power Section
CFD-G500/G500L 6-15. SCHEMATIC DIAGRAM — POWER SECTION — (Page 28) KH903 C901 C909 2200 D901 JW904 1N5401 CNJ901 D902 1N5401 JW903 JW919 C902 F902 JW905 JW918 C903 CNP902 KH941 JW906 D903 JW941 1N5401 D904 JW912 1N5401 JW942 C904 JW911... - Page 32 CFD-G500/G500L • IC Block Diagrams IC701 LC78646E-E (CD Board) IC702 BA5826FP-E2 (CD Board) IC1 TA2149BN (TUNER Board) GND1 FM RF FM RF-OUT SP– 78 77 76 75 74 73 72 71 69 68 67 66 65 64 63 62 61 D.BUFF...
- Page 33 CFD-G500/G500L IC321 BD3870FS-E2 (MAIN Board) Treble1 Treble2 Bass2 Bass1 Logic fc=8kHz fc=8kHz fo=80Hz fo=80Hz Vcc/2 Vcc/2 0dB- -87dB Vcc/2 Vcc/2 Vcc/2 IC301 TA2068N (TC Board) LINE L.RAD L.PO MIC I/EX AMP1 BUF AMP TAPE L.NF RADIO L.LINE AMP1 L.RO MONITOR...
- Page 34 CFD-G500/G500L • IC PIN FUNCTION DESCRIPTION • IC801 µPD789478GC-A24-8BT System Control (MAIN Board) Pin No. Pin Name Description 1, 2 – Not used (open) VLC2 LCD bias power supply VLC1 LCD bias power supply VLC0 LCD bias power supply 6 to 9...
- Page 35 CFD-G500/G500L Pin No. Pin Name Description – Power supply – Ground Main system clock oscillator input (4.19MHz) Main system clock oscillator output (4.19MHz) System reset signal input CD function signal output “L”: active LED CONT LED control signal output (not used)
-
Page 36: Exploded Views
CFD-G500/G500L SECTION 7 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • The mechanical parts with no reference The components identified by mark 0 or may have some difference from the original number in the exploded views are not supplied. -
Page 37: Cabinet (Front) Section
CFD-G500/G500L Ver. 1.2 7-2. CABINET (FRONT) SECTION Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-2021-767-1 PANEL LCD SUB ASSY 3-264-886-01 BUTTON VOLUME 3-264-881-01 RING ORNAMENT 3-264-882-02 PLATE, LED LIGHT GUIDE * 60 1-860-919-11 CONTROL 3 BOARD... -
Page 38: Cabinet (Rear) Section
CFD-G500/G500L 7-3. CABINET (REAR) SECTION T901 F902 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-264-908-01 CHASSIS (TRANS) 3-238-135-01 TERMINAL (-), BATTERY * 102 1-860-920-11 POWER BOARD * 110 1-860-914-11 BAT 1 BOARD * 103 1-860-921-11 TRANS BOARD... -
Page 39: Cabinet (Upper) Section-1
CFD-G500/G500L 7-4. CABINET (UPPER) SECTION-1 ANT1 cabinet (upper) S801 section-2 supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-252-828-01 SCREW (B2.6), (+) PWH TAPPING 3-019-395-01 PLATE, CHUCKING * 152 1-860-916-11 H/P BOARD 1-452-899-11 MAGNET 3-264-898-01 BUTTON POWER... -
Page 40: Cabinet (Upper) Section-2
CFD-G500/G500L Ver. 1.4 7-5. CABINET (UPPER) SECTION-2 tape mechanism deck section CD MECHANISM SECTION KSM-213CDP or KSM-213RDP Refer to SUPPLEMENT-1 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-264-890-01 BUTTON PAUSE * 213 A-4547-452-A MAIN BOARD, COMPLETE (AEP, UK, CET) -
Page 41: Tape Mechanism Deck Section
CFD-G500/G500L 7-6. TAPE MECHANISM DECK SECTION supplied M971 supplied supplied supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-244-079-01 BELT (B), SUB 3-237-719-02 CHASSIS, TC 3-244-080-01 BELT (B), MAIN 3-237-718-01 LEVER REC 3-254-029-01 SCREW A-3172-207-A MF-G500... -
Page 42: Electrical Parts List
CFD-G500/G500L SECTION 8 BAT 1 BAT 2 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they When indicating parts by reference number, parts list may be different from the parts are seldom required for routine service. - Page 43 CFD-G500/G500L CONTROL 1 CONTROL 2 CONTROL 3 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R706 1-216-841-11 METAL CHIP 1/10W R406 1-216-825-11 METAL CHIP 2.2K 1/10W R707 1-216-797-11 METAL CHIP 1/10W R407 1-216-821-11 METAL CHIP 1/10W...
- Page 44 CFD-G500/G500L Ver. 1.4 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < JACK > R894 1-216-829-11 METAL CHIP 4.7K 1/10W R895 1-216-845-11 METAL CHIP 100K 1/10W J381 1-779-050-41 JACK (LINE IN) ************************************************************ J391 1-794-016-11 JACK (i) A-1166-606-A MAIN BOARD, COMPLETE (US) <...
- Page 45 CFD-G500/G500L MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C338 1-126-964-11 ELECT 10uF C960 1-126-923-91 ELECT 220uF C339 1-104-658-91 ELECT 100uF C961 1-126-923-91 ELECT 220uF C340 1-104-658-91 ELECT 100uF C972 1-164-156-11 CERAMIC CHIP 0.1uF C341...
- Page 46 CFD-G500/G500L MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q952 8-729-037-03 TRANSISTOR KTA1266GR-AT R362 1-216-822-11 METAL CHIP 1.2K 1/10W Q953 8-729-029-09 TRANSISTOR DTC143EUA-T106 R364 1-216-857-11 METAL CHIP 1/10W Q954 8-729-036-89 TRANSISTOR KTC3198GR-AT R365 1-216-857-11 METAL CHIP...
- Page 47 CFD-G500/G500L MAIN POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R863 1-216-864-11 SHORT CHIP 0 (AEP,UK,CET) R8005 1-216-833-11 METAL CHIP 1/10W R864 1-216-825-11 METAL CHIP 2.2K 1/10W R8006 1-216-833-11 METAL CHIP 1/10W R865 1-216-821-11 METAL CHIP...
- Page 48 CFD-G500/G500L POWER TRANS Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D903 8-719-046-47 DIODE 1N5401TM R102 1-216-807-11 METAL CHIP 1/10W D904 8-719-046-47 DIODE 1N5401TM R103 1-216-843-11 METAL CHIP 1/10W R104 1-216-835-11 METAL CHIP 1/10W ************************************************************ R105...
- Page 49 CFD-G500/G500L TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-4547-438-A TUNER BOARD, COMPLETE (US,CND,E) 1-162-923-11 CERAMIC CHIP 47PF A-4547-448-A TUNER BOARD, COMPLETE (SP,AUS) (AEP,UK,CET) A-4547-451-A TUNER BOARD, COMPLETE (AEP,UK,CET) 1-164-230-11 CERAMIC CHIP 220PF ********************** (AEP,UK,CET)
- Page 50 CFD-G500/G500L TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-760-235-81 FILTER, CERAMIC (US,CND,E,SP,AUS) 8-729-920-38 TRANSISTOR 2SC2059K-N (AEP,UK,CET) 1-781-962-21 FILTER, CERAMIC 8-729-054-77 TRANSISTOR 2SC4098-T106-PQ < CONNECTOR > (AEP,UK,CET) 8-729-106-07 TRANSISTOR 2SK514-H (AEP,UK,CET) * CNP1 1-785-663-11 PIN, CONNECTOR (PC BOARD) 11P <...
- Page 51 CFD-G500/G500L Ver. 1.3 TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-216-825-11 METAL CHIP 2.2K 1/10W ACCESSORIES 1-216-829-11 METAL CHIP 4.7K 1/10W *********** (AEP,UK,CET) 1-216-833-11 METAL CHIP 1/10W A-1055-238-A REMOTE COMMANDER (RMT-CG500AD) (US,CND,E,SP,AUS) (G500L) 1-216-821-11 METAL CHIP...
- Page 52 CFD-G500/G500L MEMO...
- Page 53 CFD-G500/G500L US Model Canadian Model SERVICE MANUAL E Model Australian Model CFD-G500 Ver. 1.1 2004. 11 AEP Model CFD-G500/G500L UK Model CFD-G500L SUPPLEMENT-1 File this supplement with the service manual. Subject: Change of Optical Pick-up Block (KSM-213RDP→KSM-213CDP) Optical pick-up block is changed from KSM-213RDP to KSM-213CDP in the midway of production.
- Page 54 CFD-G500/G500L OPTICAL PICK-UP SECTION (KSM–213RDP) M701 supplied M702 Les composants identifiés par The components identified by mark 0 or dotted line with mark une marque 0 sont critiques 0 are critical for safety. pour la sécurité. Replace only with part number Ne les remplacer que par une specified.
- Page 55 CFD-G500/G500L OPTICAL PICK-UP SECTION (KSM-213CDP) not supplied M701 M702 The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce...
-
Page 56: Revision History
CFD-G500/G500L REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2004.04...