Zte MF90 User Manual

LEGAL INFORMATION
Copyright © 2014 ZTE CORPORATION.
All rights reserved.
No part of this publication may be excerpted, reproduced, trans-
lated or utilized in any form or by any means, electronic or me-
chanical, including photocopying and microfilm, without the prior
ZTE MF90 written permission of ZTE Corporation.
Let's go
The manual is published by ZTE Corporation. We reserve the
right to make modifications on print errors or update specifica-
tions without prior notice.
Getting started with your device.
Version No.: R1.0
Edition Time: July 27, 2014
Manual No.: 079584506717
NOTE:
Do not use the device in an enclosed environment or where
heat dissipation is poor. Prolonged work in such space may
cause excessive heat and raise ambient temperature, which
may lead to automatic shutdown of the device for your safety. In
the case of such event, cool the device in a well-ventilated place
before turning on for normal use.
ZTE CORPORATION
1
Installing Your Device 3. Insert the microSDHC card if necessary.
1. Slide the back cover and remove it
4. Insert the battery.
2. Install a SIM (or USIM) card to the SIM (or USIM) card slot.
The following figure shows the correct installation direction.
IMPORTANT:
Your device does not support Micro/Nano or any other nonstan-
dard SIM cards. To avoid device damage, please do not use
them.
5. Close the back cover.
7
Getting to Know Your Device
Appearance
The following figure is for your reference only.
1. LED Indicators
2. Power Button
3. WPS Button
4. Micro USB Port
5. SIM (or USIM) Card Slot
6. RESET Button
7. microSDHC Card Slot
NOTE:
microSDHC logo is a trademark of SD-3C, LLC.
2 3
Connecting to Your Device
Using Wi-Fi
1. Power on your device.
2. Use the Wi-Fi application on a client to search for available
wireless networks.
NOTE:
Set the client to obtain an IP address automatically. For the de-
tailed procedure, refer to Configuring Your PC. The client gets
an IP address, for example, 192.168.0.101.
8 9
Indicators
Indicator Status Description
Error status. Not registered to
the mobile network, no SIM
Red solid
(or USIM) card inserted or no
network service available.
Registered to the 2G/3G net-
Network Battery
Green solid
work.
Connected to the 2G/3G net-
Green blinking work and data is being trans-
ferred.
Blue solid Registered to the 4G network.
Connected to the 4G network
Blue blinking
and data is being transferred.
Blue solid WPS is active.
Wi-Fi
Blue blinking Wi-Fi is active.
Connection Scenario
Wi-Fi is off or your device is in
LED light off
The device can access the Internet in two ways and allows mul-
sleep mode.
tiple clients to surf on the Internet at the same time. The follow-
ing figure is for your reference only.
4
3. Select the SSID of your device, and then click Connect. 5. Wait until the client is connected to your device success-
fully.
NOTE:
You can find the default SSID on the label of your device.
4. Enter the password, and then click Connect.
Using a USB Cable
1. Connect a client to your device through a USB cable.
NOTE:
2. Power on your device. The operating system detects and
You may need to enter the password for the Wi-Fi connection.
identifies new hardware, and automatically finishes the in-
You can view the label on your device to get the default pass-
stallation.
word.
10
• 4G Mode: A SIM or USIM card can be used to access the
The battery is empty. Please
Red blinking
Internet.
charge the battery.
• The battery is low. Please
charge the battery.
Red solid
• The battery is in the over-
voltage charging status.
• Blinks every 2 seconds
when the battery is being
charged.
Green blinking • Blinks every 8 seconds • Internet Wi-Fi Mode: Your device can be connected to a
when your device is in
WLAN device (such as a hotspot device or wireless router)
sleep mode and not being
through Wi-Fi to access the Internet. The WLAN device
charged. must be already connected to the Internet.
NOTE:
The battery level is middle or
Green solid
Your device and the WLAN device must be in different subnets.
high.
LED light off The battery is not inserted.
5
NOTE:
If the system does not automatically launch installation, you can
run the installation program in the My Computer/airtel 4G path.
3. Wait until the client is connected to your device success-
fully.
Using the WPS(Optional)
If your client device supports WPS, you don't have to input the
password manually after WPS has been available. Please do
the following:
1. Power on your device, and enable the Wi-Fi function on
your device.
2. Press and hold the WPS button on your device about five
seconds to start Wi-Fi Protected Setup authentication pro-
cess.
3. Enable the WPS function on your client to respond this au-
thentication process.
4. Follow the system prompts on your client to finish the con-
nection.
NOTE:
For the detailed operations about the client, please refer to the
client's instruction.
11
6
12