Kenwood ts-990s Instruction Manual page 26

16 USEFUL FUNCTIONS
List of Functions for Key Assignment
Parameter Operation and activation of function assigned
MENU 0-00 to Press to access a menu ranging from 0-00 to 9-03.
MENU 9-03 For details, refer to "Menu".
Press to tune the signal using and via the internal
antenna tuner or leave the signal not tuned by
AT/AT TUNE bypassing (through) the internal antenna tuner.
Press and hold to begin tuning the internal antenna
tuner.
Press to toggle the VOX function between active and
VOX/SEL inactive.
Press and hold to open the VOX Level screen.
Press to toggle the Speech Processor between
active and inactive.
PROC/SEL
Press and hold to open the Speech Processor
screen.
ANT1 Press to select ANT 1.
ANT2 Press to select ANT 2.
ANT3 Press to select ANT 3.
ANT4 Press to select ANT 4.
Press to select Data 1.
DATA 1/SEL Press and hold to open the Modulation Source
screen.
Press to select Data 2.
DATA 2/SEL Press and hold to open the Modulation Source
screen.
Press to select Data 3.
DATA 3/SEL Press and hold to open the Modulation Source
screen.
Press to place the transceiver, with the dual band
RX (Main Band) in the receive state, in the receive state using the
single band.
Press to allow the transceiver to transmit using the
TX (Main Band)
main band frequency (Simplex).
Press to copy the operating data such as the
M>S main band frequency and operating mode to the
operating data for the sub band.
Press to toggle the reception capability for the sub
M/S
band between active and inactive.
Press to toggle the dual-band watch (reception)
RX (Sub Band)
between ON and OFF.
Press to configure the transmit functions to the sub
band frequency and place the transceiver in split
mode.
TX (Sub Band)/
Press and hold to enable the configuration for split
(Split Frequency)
frequency.
This is the default for Menu 28, "Microphone PF 1:
Key Assignment".
While [TF-SET] is pressed down, the transceiver
TF-SET
receives on the transmit frequency.
Press to select the main band.
MAIN This is the default for Menu 27, "Microphone PF 2:
Key Assignment".
Press to select the sub band.
SUB This is the default for Menu 29, "Microphone PF 3:
Key Assignment".
Each time you press this key, the operating mode
M/V (Memory) toggles between Memory Channel mode and VFO
mode.
Press to toggle the memory scroll mode between
M.IN (Memory)
active and inactive.
The operating data configured for the Memory
Channel will be copied to the VFO.
M>V (Memory)
This is the default for Menu 30, "Microphone PF 4:
Key Assignment".
Each time you press this key, normal recording
REC (Recorder)/
starts.
Full-time REC
Press and hold to start constant recording.
STOP (Recorder) Press to stop recording or playback.
Press to play back the latest audio file recorded in
PLAY (Recorder) normal or constant recording mode. Press this key
during playback to pause.
16-8
Parameter
S.DISP/SEL
{page 3-2}
MR/SEL (Quick
Memory)
M.IN (Quick
Memory)
CW T. (Main
Band)
FIL A/SEL (Main
Band)
FIL B/SEL (Main
Band)
FIL C/SEL (Main
Band)
AGC SEL (Main
Band)
AGC SLOW (Main
Band)
AGC MID (Main
Band)
AGC FAST (Main
Band)
AGC OFF (Main
Band)
NCH SEL (Main
Band)
A.NCH SEL (Main
Band)
BEF SEL (Main
Band)
APF SEL (Main
Band)
MUTE (Main
Band)
CW T. (Sub Band) Press to start CW auto tuning for the sub band.
FIL A/SEL (Sub
Band)
FIL B/SEL (Sub
Band)
FIL C/SEL (Sub
Band)
AGC/SEL (Sub
Band)
AGC SLOW (Sub
Band)
AGC MID (Sub
Band)
AGC FAST (Sub
Band)
AGC OFF (Sub
Band)
NCH SEL (Sub
Band)
A.NCH/SEL (Sub
Band)
BEF SEL (Sub
Band)
Operation and activation of function assigned
Each time you press this key, the display contents
for the sub-screen changes.
Each time you press and hold this key, the
highlighted display toggles between active and
inactive.
Each time you press this key, the Quick Memory
mode toggles between active and inactive.
Press and hold to clear all the operating data stored
in Quick Memory Channels.
Press to save data in Quick Memory Channels.
Press to activate CW auto tuning for the main band.
Press to select RX Filter A for the main band.
Press and hold to open the Receive Filter screen.
Press to select RX Filter B for the main band.
Press and hold to open the Receive Filter screen.
Press to select RX Filter C for the main band.
Press and hold to open the Receive Filter screen.
Press to open the AGC screen for the main band.
The transceiver does not respond if you press and
hold this PF key.
Press to select "Slow" for the Automatic Gain
Control speed for the main band.
Press to select "Medium" for the Automatic Gain
Control speed for the main band.
Press to select "Fast" for the Automatic Gain Control
speed for the main band.
Press to disable the Automatic Gain Control for the
main band.
Press to select either narrow or wide for the notch
filter bandwidth. The transceiver does not respond if
you press and hold this PF key.
Press to open the Auto Notch Filter screen. The
transceiver does not respond if you press and hold
this PF key.
Press to open the Band Elimination Filter screen
for the main band. The transceiver does not respond
if you press and hold this PF key.
Press to open the Audio Peak Filter screen for the
main band. The transceiver does not respond if you
press and hold this PF key.
Press to mute the audio for the main band.
Press to select RX Filter A for the sub band.
Press and hold to open the Receive Filter screen.
Press to select RX Filter B for the sub band.
Press and hold to open the Receive Filter screen.
Press to select RX Filter C for the sub band.
Press and hold to open the Receive Filter screen.
Press to open the AGC screen for the sub band. The
transceiver does not respond if you press and hold
this PF key.
Press to select "Slow" for the Automatic Gain
Control speed for the sub band.
Press to select "Medium" for the Automatic Gain
Control speed for the sub band.
Press to select "Fast" for the Automatic Gain Control
speed for the sub band.
Press to disable the Automatic Gain Control for the
sub band.
Press to select either narrow or wide for the notch
filter bandwidth for the sub band. The transceiver
does not respond if you press and hold this PF key.
Press to open the Auto Notch Filter screen. The
transceiver does not respond if you press and hold
this PF key.
Press to open the Band Elimination Filter screen
for the sub band. The transceiver does not respond if
you press and hold this PF key.
Index Contents