Fs-10, 11, 14, 16 Programming Instructions - Amana A1200S Service

FS-10, 11, 14, 16 ,17, 20 Programming Instructions
!
As shipped from the factory, the controller in the oven is
present to 100% power and standard times as shown
below
Button Time
1 :10
2 :20
3 :30
4 :45
5 :50
(10 is shown as 0 on panel)
Programming Times Only
Any button may be programmed for heating times from
1 second to 39 minutes and 59 seconds (:01 to 39:59).
To Reprogram the Times You Want:
1. Open the oven door, leave open.
2. Enter the "Manager's Mode" (programming) code
"614", push buttons 6,1 and 4.
3. Close the oven door, note "PROG" or flashing
colons on early models in display indicating the
timer is in the "Manager's Mode".
NOTE: Early production ovens (Rev. 000, .A) show
flashing colons, all other revisions (.B and
later) will show "PROG" in the display.
4. Push the button to be reprogrammed. Note that the
button number and programmed time appears in the
display.
5. To change cook times:
Push and hold in button
1 to change seconds
Push and hold in button
2 to change tens of seconds
Push and hold in button
3 to change minutes
Push and hold in button
4 to change tens of minutes
NOTE: If you miss the number you want, continue to
hold. Momentary pushes will advance the
count one number at a time.
6. When you have entered the time you want, push
button 5.
7. If you want to reprogram another button, repeat
steps 4,5 and 6.
8. When you have completed programming the buttons
you wish to change, open and close the oven door
to exit the "Manager's Mode" and go back to normal
operation.
WARNING
Button Time
6 1:00
7 1:15
8 1:30
9 1:45
10 2:00
"00:01"
"00:10"
"01:00"
"10:00"
To avoid risk of electrical shock, personal injury, or death,
disconnect power to unit and discharge the capacitor
before following any disassembly procedures.
Programming Notes:
1. If you make and error while programming push the
"Change Time" button once to clear the error. Go
back to the programming step you were on.
2. While you are programming, if one minute elapses
before you push a button, the oven will shut down. To
continue programming, re-enter the "Manager's Mode"
and begin with the last button you were programming.
3. If two stage heating has been previously programmed,
total time for a button will be defrost time plus the time
you just programmed.
NOTE: See two-stage programming instructions below.
Programming Power Level Only
1. Open the oven door, leave open.
2. Enter the "Manager's Mode" (programming) code
"614", push buttons 6,1 and 4.
3. Close the oven door, note "PROG" or flashing colons
on early models in display indicating the timer is in the
"Manager's Mode".
NOTE: Early production ovens (Rev. 000, .A) show
flashing colons, all other revisions (.B and later)
will show "PROG" in the display.
4. Push the button to be reprogrammed. Note that the
button number appears in the display and an indicator
light appears near one of the power level settings
(100%, 80%, 50% or 30%).
5. To change to a different power level, push the desired
button: 100%, 80%, 50% or 30%.
Push button 5.
6. If you want to change power level on another button,
repeat steps 4 and 5.
7. When you have completed programming the buttons
you wish to change, open and close the oven door to
exit the "Manager's Mode" and go back to normal
operation.
45 RE220002 Rev. 6