Panasonic PT-DZ21KU Operating Instructions Manual page 95

Enables the backup function
between the DVI-D input and the
HDMI input.
The input is switched as seamless
as possible when the same signal is
[ON] /[1]
*1 *2 input to the primary and secondary
inputs.
Primary input is fixed to the <DVI-D
IN> terminal, and the secondary
input is fixed to the <HDMI IN>
terminal.
Enables the backup function
between the SDI1 input and the
SDI2 input.
The input is switched as seamless
as possible when the same signal is
[2]
*2
input to the primary and secondary
inputs.
Primary input is fixed to the <SDI IN
1> terminal, and the secondary input
is fixed to the <SDI IN 2> terminal.
*1: Only for PT-DW17KU
*2: Only for PT-DZ21KU, PT-DS20KU
5) Press ▲▼ to select [AUTOMATIC
SWITCHING].
▶
z When [BACKUP INPUT MODE] is set to
[OFF], [AUTOMATIC SWITCHING] cannot be
selected.
6) Press ◀▶ to switch the item.
▶
z The items will switch each time you press the
button.
Disables the automatic input
[DISABLE]
switching function.
Switches to the secondary input
[ENABLE] automatically when the input signal
for primary input is disrupted.
Note
z Backup function is enabled when [BACKUP INPUT
MODE] is set to [ON] or [1], and the same signal is
input to the <DVI-D IN> and <HDMI IN> terminals.
Backup function is also enabled when [BACKUP
INPUT MODE] is set to [2], and the same signal is
input to the <SDI IN 1> and <SDI IN 2> terminals.
z To switch to the backup input signal using the
backup function, make sure that the following three
conditions are satisfied to be ready to use the
function.
–▶Set [BACKUP INPUT MODE] to [ON], [1], or [2].
–▶Input the same signal to the primary and
secondary inputs.
–▶Display the image of the primary input.
z If the input is switched to other than the primary or
secondary input while the backup function is ready
for use, the state of readiness to use the backup
function is canceled. To switch to the backup input
signal using the backup function again, switch to
the primary input.
z When [BACKUP INPUT MODE] is set to [ON], [1],
[DISPLAY OPTION] menu
or [2], [BACKUP INPUT STATUS] is displayed both
in the input guide ( page 98) and on the [STATUS]

screen ( pages 61, 112).

When switching to the backup input signal is
possible using the backup function, [ACTIVE] is
displayed in [BACKUP INPUT STATUS]. When it is
not possible, [INACTIVE] is displayed instead.
When [BACKUP INPUT STATUS] is [ACTIVE] while
the image of the primary input is displayed, the
secondary input becomes the backup input.
When [BACKUP INPUT STATUS] is [ACTIVE] while
the image of the secondary input is displayed, the
primary input becomes the backup input.
z If the inputs of DVI-D and HDMI are switched while
[BACKUP INPUT MODE] is set to [ON] or [1] and
switching to the backup input signal is possible, the
input is switched seamlessly.
z If the inputs of SDI1 and SDI2 are switched while
[BACKUP INPUT MODE] is set to [2] and switching
to the backup input signal is possible, the input is
switched seamlessly.
z When [AUTOMATIC SWITCHING] is set to
[ENABLE], and [BACKUP INPUT STATUS] is
[ACTIVE], the signal is switched to the backup input
if the input signal is disrupted.
z When [AUTOMATIC SWITCHING] is set to
[ENABLE] and the signal is automatically switched
to the backup input due to disruption of the input
signal, [BACKUP INPUT STATUS] changes to
[INACTIVE]. In this case, switching to the backup
input signal is not possible until the original input
signal is restored. If the signal is automatically
switched to the backup input, switching to the
backup input signal becomes possible when the
original input signal is restored. In this case, the
current input is retained.
z [BACKUP INPUT SETTING] cannot be set during P
IN P. The backup operation is not performed either.
z [BACKUP INPUT SETTING] cannot be set when
[3D SIMUL INPUT SETTING] is set to [AUTO]. The
backup operation is not performed either.
z [BACKUP INPUT SETTING] cannot be set when
[SDI LINK] is set to [DUAL LINK]. The backup
operation is not performed either.
ENGLISH - 95