Radio Operations; Radio Data System Operations - Clarion FZ502E Owner's Manual And Installation Manual

Radio Operations

Select tuner as playing source
Press the [CONTROL] knob or [SRC]
button on the remote control once or more
to enter RADIO mode.
Select one radio band
Press and hold the [CONTROL] knob (up
long press) on the panel or [BAND/TOP]
button on the remote control to select one
radio band among FM1, FM2, FM3, MW
and LW.
Manual tuning
During manual tuning, the frequency will be
changed in steps.
Press the [CONTROL] knob (left / right)
on the panel or [ , ] buttons on the
remote control to tune in a higher / lower
station.
Auto tuning
Press and hold the [CONTROL] knob (left
/ right) on the panel or [ , ] buttons on
the remote control to seek a higher / lower
station.
To stop searching, repeat the operation
above or press other buttons having radio
functions.
Note:
When a station is received, searching stops
and the station is played.
Preset scan
Preset scan receives the stations stored
in preset memory in order. This function is
useful when searching for a desired station
in memory.
1. Press the [SCN/PS/AS] button on the
remote control .
2. When a desired station is tuned in, press
the [SCN/PS/AS] button on the remote
control again to continue receiving that
station.
Note:
Be careful not to press and hold the
[SCN/PS/AS] button, otherwise the auto
store function is engaged and the unit starts
storing stations.
Auto store
Only stations with sufficient signal strength
will be detected and stored in the memory.
Press and hold the [SCN/PS/AS] button on
the remote control to start automatic station
search.
To stop auto store, press other buttons
having radio functions.
Notes:
1. After auto store, the previous stored
stations will be overwritten.
2. The unit has 5 bands, such as FM1, FM2,
FM3, MW, LW. FM3 and MW, LW can
store by AS function. Each bands can
store 6 stations, FZ502E can store 30
stations in total.
Manual store
When one expected radio station has been
detected, press and hold number button
on the remote control 1-6 to store it in the
memory.
Recall the stored stations
Press one numeric button among 1 to
6 on the remote control to select the
corresponding stored station.
Press the [CONTROL] knob (up / down) on
the panel to tune in a higher / lower station.
Local seeking
When LOCAL seeking is on, only those radio
stations with strong radio signal could be
received.
To open or close LOCAL function, set to
system setup by long pressing [CONTROL]
knob on the front panel, then press the
[CONTROL] knob(left / right) repeatedly until
LO or DX displays on the screen, rotate the
[CONTROL] knob to select Local or Distant
mode.
Note:
The number of radio stations that can be
received will decrease after the local seeking
mode is on.
Autogood products «130»

Radio Data System Operations

Radio Data System
This unit has a built-in "Radio Data System"
decoder system that supports broadcast
stations transmitting "Radio Data System"
data.
When using the "Radio Data System"
function, always set the radio to FM mode.
AF function
The AF function switches to a different
frequency on the same network in order to
maintain optimum reception.
* The factory default setting is ON.
1. In A D J m o d e ( RADIO mode) , p r e s s
[CONTROL] knob (left / right) to select
options.
2. Press the [CONTROL] knob (left / right) to
select "AF".
3. Rotate the [CONTROL] knob to select ON
or OFF.
• AF ON:
"AF" indicator appears in the display and
AF function turns on.
• AF OFF:
"AF" indicator disappears in the display
and AF function turns off.
REG (Regional programme)
function
When the REG function is ON, the optimum
regional station can be received. When this
function is OFF, if the regional station area
switches as you drive, a regional station for
that region is received.
* The factory default setting is ON.
Notes:
• This function is disabled when a national
station such as BBC R2 is being received.
• The REG function ON/OFF setting is valid
when the AF function is ON.
1. In ADJ mode, press [CONTROL] knob (left
/ right) to select options.
2. Press the [CONTROL] knob (left / right) to
select "REG".
3. Rotate the [CONTROL] knob to select ON
or OFF.
Manually tuning a regional station
in the same network
1. This function is valid when the AF function
is ON and the REG function is OFF.
Note:
• T h i s f u n c t i on can be use d whe n a
regional broadcast of the same network is
received.
TA (Traffic Announcement)
In the TA standby mode, when a traffic
announcement broadcast starts, the traffic
announcement broadcast is received as top
priority regardless of the function mode so
you can listen to it. Traffic programme (TP)
automatic tuning is also available.
* This function can only be used when
"TP" appears in the display. When "TP"
appears, this means that the "Radio Data
System" broadcast station being received
has traffic announcement programmes.
Setting the TA standby mode
If you press the [TA] button on the remote
control (in ADJ mode, press [CONTROL]
knob (left / right) to select options) "TA" lights
in the display and the unit is set into the TA
standby mode until a traffic announcement
is broadcast. When a traffic announcement
broadcast starts, "TRAF INF" appears in the
display. If you press the [TA] button on the
remote control while a traffic announcement
broadcast is being received, the traffic
announcement broadcast reception is
cancelled and the unit goes into the TA
standby mode.
Cancelling the TA standby mode
As "TA" lights in the display, press the [TA]
button on the remote control. The "TA" in the
display goes off and the TA standby mode is
cancelled.
PTY (Programme Type)
This function enables you to listen to a
broadcast of the selected programme type
even if the unit is on a function mode other
than radio.
* Some countries do not yet have PTY
broadcast.
* In the TA standby mode, a TP station has
priority over a PTY broadcast station.
Selecting PTY
In ADJ mode, press [CONTROL] knob
(left / right) to select options, then rotate
the [CONTROL] knob to select PTY type,
press the [CONTROL] knob, the unit begin
searching.
FZ502E 6