Adjusting The Esc 速控器調整 - THUNDER TIGER Jackal 6544-F Instruction Manual & Parts Catalogue

14
ADJUSTING THE ESC 速控器調整
ESC SETUP
1. Turn on the transmitter (Tx) and receiver (Rx) in that order.
2. Do not move the throttle trigger. The ESC will set the neutral, full throttle
and brake automatically. It will beep twice to confi rm it is set.
ESC ADJUSTMENTS
The ESC has 5 settings that can be adjusted to
different values to suit the user.
1. Battery cut off
2. Running mode
3. Brake strength
4. Drag brake strength
5. Throttle sensitivity
6. Factory reset.
TO CHANGE ANY OF THE ESC SETTINGS
1. Turn on the TX.
2. Plug a battery into the ESC.
3. Press and hold the ESC set up button while turning on the ESC switch.
4. The ESC will beep indicating it is in adjustment mode. Release the setup
button.
5. Push the setup button to choose the setting you would like to change.
The ESC will fl ash blue and beep to show which of the settings has
been selected. Push the button once for battery cut off the ESC will fl
ash and beep once. Pushing the button again to select running mode, the
ESC will fl ash and beep twice, and so on for each setting.
ONCE YOU HAVE SELECTED THE SETTING
YOU WOULD LIKE TO CHANGE
1. Push and hold the set button. A long tone will sound to confi rm this setting
can now be changed. Release the set button.
2. Using the ESC adjustment list as a guide, press the set up button to adjust
any settings value. The red LED will fl ash and the ESC will beep to
show what value has been selected. One red fl ash and beep is value
one, two red fl ashes and beeps is value two etc.
ESC設定
1. 依序打開遙控發射器(TX)以及遙控接收器(RX)的電源。
2. 請勿作動TX的油門板機。ESC會自動設定中立點、全油門以及剎車。
設定完成後，會有嗶嗶兩聲。
ESC調整
因應使用者習慣，ESC有六種設定功能:
1. 電池低電壓斷電。
2. 行走模式。
3. 剎車力道。
4. 自動減速力道。
5. 油門靈敏度。
6. 出廠設定。
ESC設定模式
1. 打開TX的電源。
2. 將電池連接到ESC。
3. 在打開ESC電源之前，壓下並且不放開ESC設定按鈕。
4. ESC會發出嗶聲表示已進入ESC設定模式。此時請放開設定按鈕。
5. 按壓設定按鈕以選擇欲調整的功能。ESC會閃爍藍燈以及嗶聲顯示目
前在哪種功能的設定模式中。按壓按鈕一次，ESC會閃藍燈一次並發
出嗶聲一次表示已進入電池低電壓斷電設定模式。再按壓按鈕一次以
進入行走設定模式，ESC會閃藍燈以及發出嗶聲兩次。依此類推。
選定欲調整功能的模式
1. 長按設定按鈕，直到長嗶音出現，放開設定按鈕。
2. 請參閱功能調整表以設定各項功能。按壓設定按鈕來調整數值，紅燈
閃爍一次加上嗶聲一次表示數值一。依此類推。
WHEN DONE ADJUSTING A SETTING
1. Press and hold the set up button. A long tone will sound to confi rm
the ESC has returned the setting selection mode. Release the
button.
2. Repeat Step 5 to select the next setting or turn off the ESC if you
have completed your adjustments.
SETTING
1 TON /
1 FLASH
factory setting)
(
BATTERY
LiPo
CUT OFF
6.4V
RUNNING
Forward,
brake and
MODE
reverse
BRAKE
40%
STRENGTH
DRAG BRAKE
OFF
STRENGTH
THROTTLE
1 (least)
SENSITIVITY
FACTORY
NO
RESET
功能調整完畢之後
1. 長壓設定按鈕，直到長音出現表示已離開該功能設定模式，此時放開
按鈕。
2. 重複ESC設定模式的步驟5來設定欲調整的下一個功能，若已完成所有
設定，請關閉ESC電源。
位置
1 聲 /
1 閃光
( 出廠設定)
電池低電壓 LiPo
6.4V
斷電
前進,
行走模式
剎車
後退
剎車力道
40%
自動減速
OFF
力道
油門靈敏度
1(低)
回出廠設定
NO
10
2 TON / 3 TON / 4 TON /
2 FLASH 3 FLASH 4 FLASH
NiMH/NiCd
Fixed
65% of pack
5V
starting volt
Forward,
with brake,
no reverse
60% 80% 100%
5% 10% 20%
2 3 4 (most)
YES
2 聲 / 3 聲 / 4 聲 /
2 閃光 3 閃光 4 閃光
鎳氫/鎳鎘
65％的電壓 固定 5V
斷電
前進,
剎車
無後退
60% 80% 100%
5% 10% 20%
2 3 4(高)
YES
5 TON /
5 FLASH
30%
5 聲 /
5 閃光
30%