ZIEHL-ABEGG Fcontrol FTET4AHMQ-L Manuals

Manuals and User Guides for ZIEHL-ABEGG Fcontrol FTET4AHMQ-L. We have 1 ZIEHL-ABEGG Fcontrol FTET4AHMQ-L manual available for free PDF download: Operating Instructions Manual

ZIEHL-ABEGG Fcontrol FTET4AHMQ-L Operating Instructions Manual (92 pages)

Ventilation computer with frequency inverter for 1 ~ fans in agriculture

Brand: ZIEHL-ABEGG | Category: Desktop | Size: 4 MB

Table of Contents
2
General Notes
5
Meaning of the Operating Instructions
5
Target Group
5
Exclusion of Liability
5
Copyright
5
Safety Instructions
5
Intended Use
5
Explanations of Symbols
6
Product Safety
6
Requirements Placed on the Personnel / Due Diligence
6
Start-Up and During Operation
6
Work on the Device
7
Modifications / Interventions in the Device
7
Operator's Obligation of Diligence
7
Employment of External Personnel
8
Product Overview
8
Operational Area
8
Service Work
8
Transport
8
Storage
8
Disposal / Recycling
8
Mounting
9
General Notes
9
Minimum Space Requirement
9
Outdoor Installation
9
Installation Location for Agriculture
9
Temperature Influences During Commissioning
10
Electrical Installation
10
Safety Precautions
10
EMC-Compatible Installation
10
Motor Cable
10
Control Cables
10
Mains Connection
11
Mains Voltage
11
Required Quality Attributes for the Mains Voltage
11
Leakage Current, Securely Attached, Protective Earth Conductor
11
Systems with Residual Current Protective Devices
11
Inverter Output
11
Motor Connection
11
Disconnection between Controller and Motor (Repair Switch)
12
Motor Protection Function for Motors with Thermostats
12
Analog Inputs for Sensors
12
Control Output 0 - 10 V (A1, A2, A3)
13
Voltage Supply for External Devices (+24V, GND)
13
Relay Outputs (K1, K2, K3)
13
Communication
14
Networking Via MODBUS
14
RS-485 - Network Design and Interface Parameter
14
Potential at Control Voltage Connections
15
Controls and Menu
16
Switches
16
Multipurpose LC Display
17
Direct Selection Keys
18
Menu Operation
19
Menu Structure
19
The Installation Menu
20
Installation | Entry
20
Installation | Ventilation
21
Exhaustair Rate
21
Minimum Speed Cut off
21
Peak Load Fans
22
Variant of Peak Load 1
22
Variant of Peak Load 2 and 3
23
Humidity Control
23
Installation | Shutter
24
Installation | Heating 1
25
Installation | Heating 2
25
Special Function for "Piglet Nest Warm Water Heating
26
Installation | Setpoint Derating
27
Installation | Sensor Adjust
28
Installation | Heatexchange
29
Installation | Bypass Shutter
30
Installation | Exhaust System
31
Group Control Variants
33
Installation | Bus
35
Setting of Bus Addresses
37
Operation with Only One Control Unit (Stand-Alone)
37
Installation | IO Setup
37
Factory Setting Allocations / Possible Allocations
41
Installation | Diverse
42
Displaymode
42
Switch Mode
42
Preheat Operation, Stall Washing Operation
42
External Switch Extension
43
Set Protection = PIN Lock
44
Comparison of Two Sensor Values
44
Temperature Monitoring by Distance Alarms (Relative to Nominal Value)
45
Installation | Measuring Fan
45
General Description of Function
45
Configuration
46
Installation | Motorsetup
48
Menu "Motorsetup
48
Setting Motor Rated Current
48
Setting Motor Rated Voltage
49
Adjustment of the U/F Curve
49
Setting for Rampup Time and Rampdown Time
51
Setting Current Limit
51
Setting Brake Function
51
Setting Boost Value
52
Suppression of Speeds
53
Installation | Diagnostic
53
Commissioning
55
Prerequisites for Commissioning
55
Procedure for Commissioning
55
Settings for Operation
56
Menu Overview for Operation
56
Quick Info
56
Setting Ventilation
58
For Control of Ventilation
58
For Throttle Shutter Control
59
Setpoint Derating
60
Special Function: Humidity Control
61
Setting Temperature Monitoring
63
Example for Alarm Maximum Message on Stall Unit
64
Example for Overtemperature Message in Stall 3 When Networking
65
Settings for Heating
66
Settings for Heating H1
66
Two-Position Control Independent of the Ventilation Nominal Value (Factory Setting)
66
Two-Position Control Independent of the Ventilation Nominal Value
67
Heating H1 Via the 0
68
Settings for Heating H2 (Factory Setting Deactivated)
69
Increase Program
70
Set the Trajectory of the Growth Curve
70
Curve for Setpoint Compartment Temperature
71
Curve for Minimum Ventilation
71
Curve for Maximum Ventilation
72
Curve for Heating1
72
Curve for Heating2
72
10 Menu Tables
73
Main Menu
73
Installation Menu
75
Programmed Outputs and Inputs of a System
80
11 Malfunctions / Trouble Shooting
80
Fault Messages
80
Behaviour of Outputs During Operation and Faults
82
12 Enclosure
83
Technical Data
83
Performance Reduction During Elevated Ambient Temperatures
84
Connection Diagram
85
Dimensions [MM]
86
Application Examples
87
FTET6/10AHMQ-L: Single Exhaust System with 1~ Fans
87
FTET6/10AHMQ-L: Central Exhaust Air with Activation of Group 2
88
FTET6/10AHMQ-L and CTE/AHQ(X)-L: with Activation of Groups for Central Exhaust Air
89
Index
91
Manufacturer Reference
92
Service Note
92

ZIEHL-ABEGG Categories

Fan Engine DC Drives Control Unit Controller

More ZIEHL-ABEGG Manuals

ZIEHL-ABEGG Fcontrol FTET4AHMQ-L Manuals

ZIEHL-ABEGG Fcontrol FTET4AHMQ-L Operating Instructions Manual (92 pages)

Table of Contents

Related Products

ZIEHL-ABEGG Categories