YSI 605876 Manuals

Manuals and User Guides for YSI 605876. We have 1 YSI 605876 manual available for free PDF download: User Manual

YSI 605876 User Manual

YSI 605876 User Manual (139 pages)

Monitor and Control Instrument

Brand: YSI | Category: Control Systems | Size: 5 MB

Table of Contents

Table of Contents
2
Introduction

5
2 Safety

11
- This Is Important
  11
  - Warnings and Cautions
    11
    
    Warnings
    11
    
    Cautions
    12
  - Health and Safety (Calibration Solutions)
    13
    
    Calibration Solutions
    13
Installation & Wiring

13
- Hardware Installation
  14
  - Step 1 Install 5200A
    14
    
    Location Considerations
    14
    
    Mount the 5200A
    15
    
    Panel Mount
    15
    
    Rail Mount
    15
    
    Surface Mount
    15
    
    Install the Weather Shield
    17
  - Step 2 Locate and Install Probe/Cable Assembly
    18
    
    Location Considerations
    18
    
    YSI 5561 Probe Assembly
    18
    
    YSI 5562 Probe Assembly
    19
  - Wiring Information
    19
    
    Pcbs
    19
    
    5200A Bulkhead Fittings
    20
    
    Accessing the I/O Board
    20
    
    Close Front Panel
    21
    
    Control Board
    21
    
    Open Front Panel to Access I/O Board
    21
  - Step 3 Ground 5200A
    21
    
    Directions to Ground 5200A
    22
  - Step 4 Wire Power
    22
    
    Directions to Wire AC Power
    22
    
    Wire AC Power
    22
    
    Directions to Wire DC Power/DC Backup Power
    23
    
    Wire DC Power and Backup Power
    23
  - Step 5 Wire Relay Outputs
    24
    
    Directions to Wire Relay Outputs
    24
    
    Wiring a Contactor
    25
  - Step 6 Wire aux Inputs
    25
    
    Directions to Wire aux Inputs
    25
  - Step 7 Wire Network
    27
    
    Directions to Wire Network
    27
  - Step 8 Wire Communication Equipment
    30
    
    Email Alarming
    30
    
    RS232 Communication
    30
    
    Ethernet (TCP/IP) Module Communication
    31
  - Step 9 Connect Probe/Cable Assembly
    31
  - Step 10 Install and Wire IOEM/REM Instruments
    31
  - Lightning and Surge Protection
    31
  - Sealants, Desiccants, and Securing 5200A
    32
Configuring 5200A Systems

33
- 5200A Configuration and Monitoring
  34
  - Front Panel Keys
    34
    
    Softkeys
    34
  - Run Screen
    35
    
    Run Screen Icons
    36
  - Menus
    37
    
    Submenu Screen Types
    38
  - Main Menu
    38
  - Calibration Menu
    38
    
    Getting Ready to Calibrate
    39
    
    Calibration Log
    40
    
    Conductivity
    40
    
    Directions to Calibrate Conductivity Sensor
    40
    
    Directions to Calibrate DO Sensor %Sat Value
    41
    
    Directions to Calibrate DO Sensor Mg/L Value
    42
    
    Directions to Calibrate ORP Sensor
    42
    
    Orp
    42
    
    Directions to Calibrate Ph Sensor
    43
  - Local Vs Remote Instruments
    44
  - System Menu
    44
    
    Adjust Contrast
    44
    
    Backlight Timer
    45
  - Buzzer
    45
  - Communication
    45
    
    Email Alarming
    46
    
    Ethernet
    47
    
    Node Network
    49
    
    Send Test Email Msg
    50
    
    Baud Rate RS232
    51
    
    Email Retry Delay
    51
    
    Force Serial Port
    51
    
    Non-Networked (Stand Alone) 5200As
    51
  - Configure aux
    51
    
    Input Type
    52
    
    Probe Name
    52
  - Configure E-Aux
    54
    
    Channel
    55
    
    Instrument
    55
    
    Probe Name
    55
    
    Input Type
    56
  - Data Logging
    59
    
    Clear Logs
    60
    
    Event Logging
    60
  - Date/Time
    61
  - Display Settings
    62
  - Updating 5200A Firmware
    62
    
    Firmware Updater Directions
    62
    
    Force Firmware Download
    64
  - General Alarm
    65
    
    Alarm Hold off
    65
    
    Relay
    65
  - Name Devices/Sensors
    66
  - Password
    68
  - Power Fail Menu
    68
  - Serial Number
    69
  - Service
    69
    
    Reset Clean Probes
    69
    
    Reset to Factory
    70
  - Output Test
    71
  - Service Hold
    73
  - Version
    73
- Aquamanager and the System Menu
  73
- Sensor Setup
  74
  - Control Mode
    75
    
    Set Point Control
    76
    
    Timed Versus Normal (Non Timed) Control
    77
    
    PID/PWM and PID 4/20Ma Control Mode
    78
    
    Validation Error and Autofix - Set Point Control Only
    78
    
    Aux and E-Aux Relay Digital
    81
    
    Aux and E-Aux Analog (0-1VDC, 0-5VDC and 4/20Ma)
    82
    
    Temperature
    83
    
    Conductivity
    85
    
    Configure Conductivity System
    85
    
    Temperature Compensation
    85
    
    Configure DO Sensor System
    86
    
    Salinity & Temperature Compensation for DO Readings
    86
    
    Two Range Controls for DO
    86
    
    Configure ORP Sensor System
    87
    
    Orp
    87
    
    Configure Ph System
    88
    
    Salinity
    88
    
    E-Aux System Offline
    89
    
    Enable Salinity System
    89
    
    Aquamanager and the Sensor Setup Menu
    90
    
    Configure Sensor System as a 4/20Ma Output
    90
  - Timers
    91
    
    Timers 1-4
    91
    
    Feed Mode
    92
    
    Feed Smart Tm Timer
    92
    
    Daily Feedings
    93
    
    Daily Weight
    93
    
    Fcr
    93
    
    Sensors
    94
    
    Calibrate
    95
    
    Aquamanager and the Timer Menu
    96
  - Control Menu
    97
  - Msg's Menu
    97
    
    Calibration Logs
    98
    
    Event Logs
    98
    
    Sensor Logs
    98
  - Svr Hold Menu
    98
Aquamanager

99
- Installing Aquamanager
  100
  - PC Requirements and Features
    100
  - Software Installation
    100
    
    Getting Started
    100
  - Aquamanager Windows
    101
    
    Explorer Window
    101
    
    Node (Graph) Window
    101
    
    Systems Management
    102
  - Database Management
    102
  - Autopoller
    103
    
    Aquamanager Alarm Emails
    103
    
    Mapping
    103
Maintenance

104
- Probe Maintenance at the Deployment Site
  105
- Algae and Debris
  105
  - Minimizing the Effect of Algae and Debris
    105
- Calibration Checks
  105
- Recommended Quality Assurance Protocol
  105
  - Alternative Quality Assurance Protocol (Quick Check and Adjustment)
    106
- Sensor Care and Maintenance
  106
  - DO Sensor
    106
    
    Gold Cathode Cleaning
    107
    
    Silver Anode Cleaning
    107
  - Ph and Combination Ph/Orp Sensor Cleaning
    107
  - Temperature/Conductivity Sensor Cleaning
    108
- Recommended Cleaning of the 5200A and Accessories
  108
- Storage
  108
  - Short Term Storage
    108
  - Long Term Storage
    108
    
    Probe/Cable Assembly Storage
    109
    
    Sensor Storage
    109
- Sensor Replacement
  109
- Charging DC Batteries
  109
- Aquamanager Database Maintenance
  109
- Replacement Parts & Accessories
  109
- Appendices
  110
Appendix 1 - Unpacking and Inspection

111
Appendix 2 - Troubleshooting

111
- Sensor Troubleshooting
  111
- Relay (Outputs) Troubleshooting
  112
- Email Alarm Troubleshooting
  112
- Network Troubleshooting
  113
- 5200A Systems Troubleshooting
  113
- Firmware Updater Troubleshooting
  113
- Feed Timer Troubleshooting
  113
- Aquamanager Troubleshooting
  113
Appendix 3 - Menu Maps

114
- Menu Map Key
  114
Appendix 4 - Declaration of Conformity

127
Appendix 5 Parts and Accessories

129
Appendix 6 SMS Messaging

131
Appendix 7 Warranty

132
Appendix 8 Contact Us

132
- Ordering and Technical Support
  132
- Service Information
  132
Appendix 9 Recycling

133
Appendix 9 Recycling

133
Index

133

Advertisement

Advertisement

Related Products

YSI Categories

Measuring Instruments Accessories Multimeter Laboratory Equipment Water System

More YSI Manuals