Will Burt AntennaMast AM2 Manuals

Manuals and User Guides for Will Burt AntennaMast AM2. We have 2 Will Burt AntennaMast AM2 manuals available for free PDF download: Operator's Manual

Will Burt AntennaMast AM2 Operator's Manual (52 pages)

Brand: Will Burt | Category: Antenna | Size: 2 MB

Table of Contents
5
Section 1 Safety Summary
8
Signal Word Definitions
8
Safety Instructions
8
Symbols
15
Section 2 Introduction
17
Intended Use
18
Definitions
18
Mast Component Descriptions
19
Figure 2-1 Telescoping Masts (Not to Scale)
19
Section 3 Technical Data
21
Payload Capacity and Wind Effects
21
Mast System Specifications
21
Table 3-1 Antennamast™ Model AM2 Specifications
22
Table 3-2 Antennamast™ Model AM2 with Lift Winch Specifications
23
Table 3-3 Antennamast™ Model AM2 with EZ RAZE Payload Elevation Systems Specifications
24
Section 4 Installation and Disassembly
25
Pre-Installation Check
25
Select a Suitable Mounting Location
25
Recommended Installation Tools
26
Unpack the Mast System
26
Table 4-1 Tools and Materials Required for Installation
26
Install the Tripod
27
Figure 4-1 Open Wheeled Bag
27
Figure 4-3 Extend Tripod Legs
27
Figure 4-4 Pull Pins Outward
27
Figure 4-6 Fully Deployed Tripod
27
Deploy the Mast
28
Figure 4-7 Stake the Tripod Legs
28
Manual Deployment
29
Figure 4-8 Different Tubes
29
Figure 4-9 Insert the Top Tube
29
Figure 4-10 One Hand Width from Bottom
29
Figure 4-11 Loosen the Pin of the 4-Way Guy Collar
29
Figure 4-12 Align Guy Stakes with the Four Holes on the Guy Collar
30
Figure 4-14 Manually Load Tubes
30
Figure 4-15 Tighten Clamps
30
Figure 4-18 Use Hammer to Drive in Stake
31
Deployment with Lift Winch
32
Figure 4-19 Different Tubes
32
Figure 4-20 Insert the Top Tube
32
Figure 4-21 One Hand Width from Bottom
32
Figure 4-22 Loosen the Pin of the 4-Way Guy Collar
32
Figure 4-23 Align Guy Stakes with the Four Holes on the Guy Collar
33
Figure 4-24 Insert Orange Barrel of the Orange Winch into the Tripod Receiver
33
Figure 4-25 Tighten the Black Knob
34
Figure 4-26 Reel out Enough Cable
34
Figure 4-27 Feed Cable through Base Plate
34
Figure 4-28 Put Ball End of Cable through the Bottom Hole
34
Figure 4-29 Thread the Cable End Back through the Top Hole
34
Figure 4-30 Pull the Slack out from the Bottom of the Key
34
Figure 4-31 Place the Key between the Leg Braces Opposite of the Orange Winch
35
Figure 4-32 after Ensuring Lift Winch Is Properly Set Up, Set Next Tube Onto the Raised Plug of the
35
Figure 4-33 Ensure Locking Tabs Fully Engage
35
Figure 4-34 One Hand Width below the Clamp
35
Figure 4-35 Lower Lifting Plate to the Ground
35
Figure 4-36 Lower Mast Tubes to the Ground
36
Figure 4-37 Stake the Base Plate
36
Figure 4-38 Use Hammer to Drive in Stake
36
Deployment with EZ RAZE
37
Figure 4-39 Different Tubes
37
Figure 4-40 Insert the EZ RAZE Top Tube
37
Figure 4-41 One Hand Width from Bottom
37
Figure 4-42 Engage the Kick Stand Lever
37
Figure 4-43 Slide EZ RAZE Top Tube down the Carriage
38
Figure 4-44 Attach Guy Lines to Top Guy Collar
38
Figure 4-45 Align Guy Stakes with the Four Holes on the Guy Collar
38
Figure 4-46 Insert the Round Key of the Blue Winch into the Tripod Reciever
38
Figure 4-47 Rotate the Carriage
39
Figure 4-48 Route the Cable between the Spool and Standoffs
39
Figure 4-49 Feed Cable through the 2 Eyelets on the EZ RAZE Carriage
39
Figure 4-50 Feed the Cable through the Top of the Top Pulley and Back down the Other Side of the
39
Figure 4-53 Feed End of Cable through the Bottom Hole in the Receiver Plate
40
Figure 4-54 Correct Installation
40
Figure 4-55 Reset the Kick Stand Lever
40
Figure 4-56 Leave Cable Loose While Deploying the Mast
41
Figure 4-58 Tighten Clamps
41
Figure 4-59 Lower Mast Tubes to the Ground
41
Figure 4-61 Use Hammer to Drive in Stake
41
Guy the Mast
42
Figure 4-62 Align Guy Stakes with the Four Holes on the Guy Collar
42
Figure 4-63 Drive Guy Stakes into the Ground at a 45° Angle Away from the Tripod
42
Figure 4-64 Clip Snap Hooks to Guy Collar
43
Figure 4-66 Tighten the Guy Lines
43
Install the Accessories
44
Payload Platform Installation
44
Guy Collar Installation
44
Figure 4-68 Attach Payload Platform to the Carriage
44
Figure 4-69 Pin the Arm in Place
44
Figure 4-70 Pin the Payload Adaptor in Place
44
Install the Payload
45
Disassemble the Mast
46
Section 5 Transportation
47
General Transportation
47
Shipping
47
Section 6 Maintenance and Disposal
49
Pre-Maintenance Check
49
Maintenance Equipment
49
Table 6-1 Equipment Recommended for Maintenance
49
Spare Parts
50
Periodic Maintenance
50
Figure 6-1 Periodic Inspections
50
Long-Term Storage
51
System Disposal
51

Will-Burt AntennaMast AM2 Operator's Manual (34 pages)

Manual Deploy & Deploy w/Mast Tube Lift Winch

Brand: Will-Burt | Category: Antenna | Size: 1 MB

Document History
2
Grounding Instructions
32
Maintenance
33
Warranty
34

Will Burt Categories

Valve Positioners Lighting Equipment Antenna Racks & Stands Air Compressor

More Will Burt Manuals

Will Burt AntennaMast AM2 Manuals

Will Burt AntennaMast AM2 Operator's Manual (52 pages)

Table of Contents

Will-Burt AntennaMast AM2 Operator's Manual (34 pages)

Table of Contents

Related Products

Will Burt Categories