User Manuals: Tonghui TH2827C Precision LCR Meter

Manuals and User Guides for Tonghui TH2827C Precision LCR Meter. We have 1 Tonghui TH2827C Precision LCR Meter manual available for free PDF download: Operation Manual

Tonghui TH2827C Operation Manual

Tonghui TH2827C Operation Manual (131 pages)

Precision LCR meter

Brand: Tonghui | Category: Measuring Instruments | Size: 1 MB

Table of Contents

Table of Contents
2
Chapter 1 Out of Box Audit

7
- To Inspect the Package
  7
- Power Connection
  7
- Fuse
  7
- Environment
  8
- Use of Test Fixture
  8
- Warm-Up
  8
- Other Features
  9
Chapter 2 Introduction

10
- Introduction to Front Panel
  10
- Introduction to Rear Panel
  12
- Introduction to Display Zone
  13
- Main Menu Keys and Corresponding Displayed
  14
- Meas]
  14
- Setup]
  15
- System]
  15
- Basic Operation
  15
- Start the Instrument
  15
Chapter 3 Introduction to [MEAS]

17
- Meas Display
  17
- Test Function
  17
- Test Range
  21
- Test Frequency
  21
- Test Level
  22
- DC Bias
  23
- Test Speed
  24
- Tools
  24
- Bin No. Disp
  25
- Comparator Function
  26
- Bin Count Disp
  26
- Param
  27
- Nom
  27
- Bin
  27
- High/Low
  28
- Count
  28
- Aux
  28
- Out
  28
- List Sweep Disp
  28
- Sweep Mode
  29
- FREQ (Hz)
  30
- R[:] X[:]
  30
- CMP (Compare)
  30
- Measure Setup
  30
- Trigger Mode
  31
- Auto Level Control Function
  32
- Bias Current Isolation Function
  32
- Average
  33
- Level Monitor Function
  33
- Delay Time
  34
- Output Impedance
  34
- Deviation Test Function
  35
- Correction
  36
- Open
  37
- Short
  39
- Load
  40
- Load Correction Test Function
  41
- Cable Length Selection
  42
- Limit Table
  42
- Swap Parameter
  43
- Limit Modes of Compare Function
  43
- Set Nominal Value of Tolerance Mode
  45
- Comparator Function ON/OFF
  45
- Auxiliary bin ON/OFF
  45
- High/Low
  46
- List Sweep Setup
  47
- Mode
  48
- Test Parameter
  48
- Sweep Parameter Setup
  48
Chapter 4 [SYSTEM] and <FILE MANAGE

50
- System Setup
  50
- Pass Beep
  50
- Fail Beep
  51
- Language
  51
- Pass Word
  51
- BUS MODE (Reserved Function)
  52
- GPIB ADDR (Reserved Function)
  52
- Talk Only
  52
- Bias Src
  53
- Baud Rate
  53
- Data/Time
  53
- Lcr <File Manage
  53
- Setup File for Single-Group Component (*.STA)
  54
- U-Disk Manage Performance
  55
- Operation Steps for File Management
  55
Chapter 5 Execute LCR Operation and some Examples

58
Chapter 6 Performance and Test

72
- Test Function
  72
- Parameter and Symbol
  72
- Equivalent Mode
  72
- Range
  72
- Trigger
  72
- Delay Time
  73
- Connection Modes of Test Terminals
  73
- Test Speed (Frequency>=10Khz)
  73
- Average
  73
- Display Digit
  73
- Test Signal
  73
- Test Signal Frequency
  73
- Signal Mode
  74
- Test Signal Level
  74
- Output Impedance
  74
- Monitor for Test Signal Level
  74
- Maximum Measurement Display Range
  74
- DC Bias Voltage Source
  75
- Measurement Accuracy
  75
- Accuracy of │Z│,│Y│, L, C, R, X, G, B
  75
- Accuracy of D
  75
- Accuracy of Q
  76
- Accuracy of Θ
  76
- Accuracy of G
  76
- Accuracy of Rp
  76
- Accuracy of Rs
  77
- Accuracy Factor
  77
- Accuracy of DCR
  81
- Safety Requirement
  81
- Insulation Resistance
  81
- Insulation Intensity
  81
- Leakage Current
  82
- Electromagnetic Compatibility
  82
- Performance Test
  82
- Working Condition
  82
- The Used Instruments and Devices
  82
- Function Check
  83
- Test Signal Level
  83
- Frequency
  83
- Measurement Accuracy
  83
- Accuracy of C and D
  83
- Accuracy of L
  84
- Accuracy of Z
  84
Chapter 7 Command Reference

86
- Subsystem Commands for TH2827
  86
- Display Subsystem Commands
  86
- Frequency Subsystem Commands
  88
- Voltage Subsystem Commands
  89
- Current Subsystem Commands
  89
- Amplitude Subsystem Commands
  90
- Output Resister Subsystem Commands
  90
- Output Subsystem Commands
  90
- BIAS Subsystem Commands
  91
- Function Subsystem Commands
  93
- LIST Subsystem Commands
  97
- Aperture Subsystem Commands
  101
- Trigger Subsystem Commands
  101
- Fetch? Subsystem Commands
  102
- Correction Subsystem Commands
  105
- Comparator Subsystem Commands
  110
- Mass Memory Subsystem Commands
  115
- GPIB Common Commands
  116
Chapter 8 The Description for Handler (Optional)

119
- Technical Description
  119
- The Operation Description
  119
- The Definition for the Signal Line
  119
- Electrical Feature
  127
- HANDLER Interface Board Circuit
  128
- Operation
  131

Advertisement

Advertisement

Related Products

Tonghui Categories

Measuring Instruments Test Equipment Multimeter

Power Supply

Scanner

More Tonghui Manuals