TEXIO PU80-18 Manuals

Manuals and User Guides for TEXIO PU80-18. We have 1 TEXIO PU80-18 manual available for free PDF download: Instruction Manual

TEXIO PU80-18 Instruction Manual

TEXIO PU80-18 Instruction Manual (81 pages)

PU series 1500W series DC Power Supply

Brand: TEXIO | Category: Power Supply | Size: 7 MB

Table of Contents

Table of Contents
3
Safety Instructions
10
1 General Information

13
- User Manual Content
  13
- Introduction
  13
- Accessories
  15
  - General
    15
  - Serial Link Cable
    15
  - Misc. Hardware
    15
  - AC Cables
    16
  - Serial Port Cables
    16
2 Specifications

17
- Output Rating
  17
- Input Characteristics
  17
- Constant Voltage Mode
  17
- Constant Current Mode
  17
- Analog Programming and Monitoring
  18
- OUTPUT RATING and READBACK (Rs232/485,Optional IEEE Interface) (at the Time of 23℃±5℃)
  18
- Protective Functions
  18
- Front Panel
  18
- Environmental Conditions
  19
- Mechanical
  19
- Safety/Emc
  19
- Supplemental Characteristics
  19
3 Installation

21
- General
  21
- Preparation for Use
  21
- Initial Inspection
  21
- Rack Mounting
  22
- Location, Mounting and Cooling
  22
- Ac Source Requirements
  22
- Ac Input Power Connection
  23
  - AC Input Connector
    23
  - AC Input Cord
    23
  - AC Input Wire Connection, 1500W Models
    23
  - Time to Heat Beforehand
    24
- Turn-On Checkout Procedure
  24
  - General
    24
  - Prior to Operation
    25
  - Constant Voltage Check
    25
  - Constant Current Check
    25
  - OVP Check
    26
  - UVL Check
    26
  - Foldback Check
    26
  - Address Setting
    27
  - Baud Rate Setting
    27
- Connecting the Load
  27
- Local and Remote Sensing
  34
  - Sense Wiring
    34
  - Local Sensing
    35
  - Remote Sensing
    35
  - J2 Sense Connector Technical Information
    36
4 Front and Rear Panel Controls and Connectors

37
- Introduction
  37
- Front Panel Controls and Indicators
  37
- Rear Panel
  39
- Rear Panel Sw1 Setup Switch
  40
  - SW1 Position Functions
    41
  - Resetting the SW1 Switch
    41
- Rear Panel J1 Programming and Monitoring Connector
  42
  - Making J1 Connections
    42
5 Local Operation

44
- Introduction
  44
- Standard Operation
  44
  - Constant Voltage Mode
    44
  - Constant Current Operation
    45
  - Automatic Crossover
    45
- Over Voltage Protection (Ovp)
  45
- Under Voltage Limit (Uvl)
  46
  - Setting the UVL Level
    46
- Foldback Protection
  46
  - Setting the Foldback Protection
    47
  - Resetting Activated Foldback Protection
    47
- Output On/Off Control
  47
- Output Shut-Off (So) Control Via Rear Panel J1 Connector
  47
- Enable/Disable Control Via Rear Panel J1 Connector
  48
- CV/CC Signal
  48
- Ps_Ok Signal
  49
- Safe Start and Auto-Restart Modes
  49
  - 1Automatic Start Mode
    49
  - Safe Start Mode
    49
- Over Temperature Protection (Otp)
  49
- Last Setting Memory
  50
- Series Operation
  50
  - Series Connection for Increased Output Voltage
    50
  - Series Connection for Positive and Negative Output Voltage
    52
- Parallel Operation
  53
- Daisy-Chain Connection
  54
- Front Panel Locking
  55
  - Unlocked Front Panel
    55
  - Locked Front Panel
    55
6 Remote Analog Programming

56
7 Rs232 & Rs485 Remote Control

61
- Introduction
  61
- Configuration
  61
  - Default Setting
    61
  - Address Setting
    61
  - RS232 or RS485 Selection
    61
  - Baud Rate Setting
    61
  - Setting the Unit into Remote or Local Mode
    62
  - RS232/485 Port in Local Mode
    62
  - Front Panel in Remote Mode
    62
- Rear Panel Rs232/485 Connector
  63
- Connecting Power Supplies to Rs232 or Rs485 Bus
  63
- Communication Interface Protocol
  65
  - Data Format
    65
  - Addressing
    65
  - End of Message
    65
  - Checksum
    65
  - Acknowledge
    65
  - Error Message
    66
  - Backspace
    66
- Error Messages
  66
- Command Set Description
  67
  - General Guides
    67
  - Command Set Categories
    67
  - Initialization Control Commands
    68
  - ID Control Commands
    68
  - Output Control Commands
    68
  - Status Control Commands
    70
- Status, Error and Srq Registers
  71
  - General
    71
  - Conditional Registers
    71
  - Service Request: Enable and Event Registers
    73
8 Isolated Analog Programming Option

76
- Ntroduction
  76
9 Maintenance

79
- Introduction
  79
- Units under Warranty
  79
- Periodic Maintenance
  79
- Adjustments and Calibration
  79
- Parts Replacement and Repairs
  79
- Troubleshooting
  79
- Fuse Rating
  80

Advertisement

Advertisement

Related Products

TEXIO Categories

Power Supply

Power Supply Test Equipment Portable Generator Recording Equipment Multimeter

More TEXIO Manuals