Sign In
Upload
Manuals
Brands
Texas Instruments Manuals
Measuring Instruments
GTLP
Texas Instruments GTLP Data Book Manuals
Manuals and User Guides for Texas Instruments GTLP Data Book. We have
1
Texas Instruments GTLP Data Book manual available for free PDF download: User Manual
Texas Instruments GTLP User Manual (89 pages)
Evaluation module
Brand:
Texas Instruments
| Category:
Measuring Instruments
| Size: 0.87 MB
Table of Contents
GTLP EVM Board Typical Test and Setup Configuration
5
Table of Contents
7
Introduction
13
GTLP EVM Overview
14
GTLP EVM Kit Contents
15
GTLP EVM Kit Availability
16
GTLP EVM Case
18
GTLP EVM Top Tray
19
GTLP EVM Backplane Board
20
GTLP EVM Backplane Block Diagram
21
GTLP EVM Group Assignment
21
GTLP EVM Backplane Eight-Layer Stackup
22
GTLP EVM Group 1, Bits 1 through 8 Trace Impedance
23
Connectors
24
AMP Z-PACK 2-MM, 110-Pin, Hard-Metric (HM) Male Connector
24
AMP Pin Lengths
25
AMP Single-Line-Model Data Sheet
26
Power Supply (Left) and Backplane Connection (Right)
27
TT Linear Regulator
28
Power-Supply LED Indicators
29
Clock Crystals
30
Clock Crystal on Card (Left) and Stored in Tube (Right)
30
Clock Crystal with Leads in Position for Storage
30
Termination Cards
31
Termination-Card Card Location (Left) and Close-Up View (Right)
31
Termination-Card Stackup
32
Bottom Compartment
33
Oscilloscope and Backplane Daughter-Card Storage Area
33
Measurement Equipment
34
Tektronix THS730A O-Scope
34
Clock Cards
35
GTLP EVM Clock Card
35
Clock-Card Stackup
36
Driver-Card Stackup
37
GTLP EVM Driver Daughter Card
38
Single-Bit Selection
39
Bit Selection for Normal Data Pattern (Left), Signal Held Low (Center), or
39
Signal Held High (Right)
39
Edge-Rate Control
40
ERC Bit-Selection Jumper Set for Slow (Left) or Fast (Right) Rate
40
JB2 Set to Source-Synchronous Clock (Left) or System-Clock (Right) Operation
41
Source-Synchronous Clock/System-Clock Selection
41
Receiver-Card Stackup
42
GTLP EVM Monitored Receiver Card
44
Backplane Setup
45
Insertion of Clock Cards
45
AMP Z-PACK, 2-MM, 55-Pin, HM Male (Left) and
45
Connector Premate (Left), Mating (Center), and Mated (Right)
46
Insertion of Clock Crystals
47
Clock Crystal Removal (Left) and Insertion (Right)
47
Insertion of Termination Cards
48
Slot 1 (Left) and Slot 20 (Right) Termination Cards on the Backplane
48
Insertion of Driver and Receiver Cards
49
Termination-Card Keying
48
Driver and Receiver Connector Keying
49
Close-Up View of Connector Keying
50
Proper Connector Mating Sequence (Left to Right)
50
Connectors Properly Mated
51
Oscilloscope Operation
52
Oscilloscope Setup
53
O-Scope Probe Monitor-Point Adapters
53
Measurements
54
Tektronix O-Scope Front (Left) and Top (Right)
53
Simple Test-Measurement
54
Turn on O-Scope (Left) and Select Channel (Right)
54
O-Scope Display
55
Timing Adjustment
56
Voltage Adjustment
56
Trigger Adjustment
57
Waveform Measurement and Interpretation
58
Chapter 4
59
Timing Relationship of Driver Card (D1) Data Pattern (Ch1) and Driver Card (D1) Latch Clock (Ch2)
59
Case 1: D1 Data Pattern (Ch1) and D1 Latch Clock (Ch2)
59
Timing Relationship of Driver Card (D1) Data Pattern (Ch1) and Driver Card (D1) Group 1 GTLP Data out (Ch2)
60
Case 2: D1 Data Pattern (Ch1) and D1 Group 1 GTLP Data out (Ch2)
60
Timing Relationship of Driver Card (D1) Data Pattern (Ch1) and Receiver Card (R2) Group 1 GTLP Data in (Ch2)
61
Case 3: D1 Data Pattern (Ch1) and R2 Group 1 GTLP Data in (Ch2)
61
Timing Relationship of Driver Card (D1) Data Pattern (Ch1) and Receiver Card (R2) Group 1 LVTTL Data out (Ch2)
62
Case 4: D1 Data Pattern (Ch1) and R2 Group 1 LVTTL Data out (Ch2)
62
Receiver Card (R20) Group 1 GTLP Data in (Ch2)
63
Case 5: R2 Group 1 GTLP Data in (Ch1) and R20 Group 1 GTLP Data in (Ch2)
63
Timing Relationship of Receiver Card (R2) Group 1 GTLP Data in (Ch1) and Receiver Card (R20) Group 1 GTLP Data in (Ch2)
63
GTLP Backplane Waveforms at 23-Mhz Clock Frequency
64
GTLP Monitor Test-Point Waveforms at 23-Mhz Clock Frequency
64
Monitored Waveforms
64
Troubleshooting
66
Chapter 5
67
Spare Parts
67
Spare Fuses and Jumpers
67
Replacing 5-A Fuse F2
68
Fuse F2 (Left) and Removal Procedure (Right)
68
Replacing 2.5-A Fuse F1
69
Fuse F1
69
Damage to the Daughter Cards
70
Bill of Materials, Schematics, Board Layouts, and Suggested Specifications
72
GTLP EVM Bill of Materials
73
Board Layouts and Schematics
76
Backplane Layout, Front Side
76
Backplane Layout, Back Side
77
Driver-Card and Receiver-Card Connector Pinout
78
A–4 Backplane Schematic
79
Backplane Schematic
79
Driver-Card Schematic
81
Receiver-Card Schematic
84
Advertisement
Advertisement
Related Products
Texas Instruments GRAPH LINK
Texas Instruments GC5328
Texas Instruments GC5325
Texas Instruments bq27441-G1
Texas Instruments BQ7961-Q1 Series
Texas Instruments DRV-ACC16-EVM
Texas Instruments MSP-EXPCC430RFx
Texas Instruments PHP2700
Texas Instruments TIDA-010037
Texas Instruments TLV320AIC12
Texas Instruments Categories
Motherboard
Control Unit
Microcontrollers
Computer Hardware
Calculator
More Texas Instruments Manuals
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL