TDK-Lambda 2U GENESYS 5KW Manuals

TDK-Lambda 2U GENESYS 5KW Manuals

Manuals and User Guides for TDK-Lambda 2U GENESYS 5KW. We have 1 TDK-Lambda 2U GENESYS 5KW manual available for free PDF download: Technical Manual

TDK-Lambda 2U GENESYS 5KW Technical Manual

TDK-Lambda 2U GENESYS 5KW Technical Manual (81 pages)

Programmable DC Power Supplies

Brand: TDK-Lambda | Category: Power Supply | Size: 2.27 MB

Table of Contents

Table of Contents
5
Warranty
9
Safety Instructions
10
German Safety Instructions
12
Chapter 1 General Information

14
- User Manual Content
  14
- Introduction
  14
  - General Description
    14
  - Models Covered
    14
  - Features and Options
    14
  - Multiple Output Power System
    15
  - Control Via the Serial Communication Port
    15
  - Analog Voltage Programming and Monitoring
    15
  - Parallel Operation
    15
  - Output Connections
    15
  - Cooling and Mechanical Construction
    16
- Accessories
  16
  - General
    16
  - Serial Link Cable
    16
  - Misc. Hardware
    16
  - AC Cables
    16
Chapter 2 Specifications

17
- Safety/Emc
  18
- Supplemental Characteristics
  19
- Outline Drawings
  20
Chapter 3 Installation

21
- General
  21
- Preparation for Use
  21
- Initial Inspection
  21
- Rack Mounting
  22
  - To Install the Power Supply in a Rack
    22
  - Rack Mount Slides
    22
- Location Mounting and Cooling
  22
- Ac Source Requirements
  22
- Ac Input Power Connection
  23
  - AC Input Connector
    23
  - AC Input Cord
    23
  - AC Input Wire Connection
    23
- Turn-On Checkout Procedure
  25
  - General
    25
  - Prior to Operation
    25
  - Constant Voltage Check
    25
  - Constant Current Check
    25
  - OVP Check
    25
  - UVL Check
    26
  - Foldback Check
    26
  - Address Setting
    26
  - Baud Rate Setting
    26
- Connecting the Load
  27
- Local and Remote Sensing
  34
  - Local Sensing
    34
  - Remote Sensing
    35
  - J2 Sense Connector Technical Information
    35
- Repackaging for Shipment
  35
Chapter 4 Front and Rear Panel Controls and Connectors

36
Chapter 5 Local Operation

43
- Introduction
  43
- Standard Operation
  43
  - Constant Voltage Mode
    43
  - Automatic Crossover
    44
- Over Voltage Protection (Ovp)
  44
- Under Voltage Limit
  45
  - Setting the UVL Level
    45
- Foldback Protection
  45
  - Setting the Foldback Protection
    45
  - Resetting Activated Foldback Protection
    45
- Output On/Off Control
  45
- Output Shut-Off (So) Control Via Rear Panel J1 Connector
  45
- Enable/Disable Control Via
  46
- CV/CC Signal
  46
- Ps Ok Signal
  46
- Safe Start and Auto-Restart Modes
  47
  - Safe Start Mode
    47
- Over Temperature Protection (Otp)
  47
- Last Setting Memory
  47
- Series Operation
  47
  - Series Connection for Increased Output Voltage
    48
  - Series Connection for Positive and Negative Output Voltage
    49
- Parallel Operation
  50
  - Basic Parallel Operation
    50
  - Advanced Parallel Operation
    51
- Front Panel Locking
  53
  - Unlocked Front Panel
    53
  - Locked Front Panel
    53
Chapter 6 Remote Analog Programming

54
Chapter 7 Rs232 & Rs485 Remote Control

58
- Introduction
  58
- Configuration
  58
  - Default Setting
    58
  - Address Setting
    58
  - RS232 or RS485 Selection
    58
  - Baud Rate Setting
    58
  - Setting the Unit into Remote or Local Mode
    58
  - Front Panel in Remote Mode
    59
- Rear Panel Rs232/485 Connector
  59
- MD MODE OPTION (Factory Installed)
  60
  - MD Mode Description
    60
  - MD Mode Enable - Serial Communication Mode
    60
  - MD Mode SRQ
    60
  - Communication Collisions
    60
  - MD Mode SRQ Retransmission
    60
- Connecting Power Supplies to Rs232 or Rs485 Bus
  61
  - Single Power Supply
    61
  - Multi Power Supply Connection to RS232 or RS485 BUS
    62
- Communication Interface Protocol
  62
  - Data Format
    62
  - Addressing
    62
  - End of Message
    62
  - Command Repeat
    62
  - Checksum
    62
  - Acknowledge
    62
  - Error Message
    63
  - Backspace
    63
- Error Messages
  63
- Command Set Description
  63
  - General Guides
    63
  - Command Set Categories
    63
  - Initialization Control Commands
    64
  - ID Control Commands
    64
  - Output Control Commands
    64
- Global Output Commands
  66
  - General
    66
- Single Byte Commands
  67
  - General
    67
  - Global Commands Without Response
    67
  - Global Commands with Response
    67
  - Addressed Commands with Response
    68
  - Addressed Commands Without Response
    68
  - Status Control Commands
    71
- Status, Error and Srq Registers
  71
- Serial Communication Test Set-Up
  76
Chapter 8 Isolated Analog Progamming Option

77

Advertisement

Advertisement

Related Products

TDK-Lambda Categories

Power Supply

Power Supply Media Converter Cables and connectors Portable Generator Network Hardware

More TDK-Lambda Manuals