User Manuals: Super Systems 9130 Series Controller

User Manuals: Super Systems 9130 Series Controller

Manuals and User Guides for Super Systems 9130 Series Controller. We have 1 Super Systems 9130 Series Controller manual available for free PDF download: Operation Manual

Super Systems 9130 Series Operation Manual

Super Systems 9130 Series Operation Manual (192 pages)

SINGLE-LOOP PROGRAMMABLE TEMPERATURE CONTROLLER

Brand: Super Systems | Category: Temperature Controller | Size: 6 MB

Table of Contents

Table of Contents
3
Installation Safety Requirements
6
Chapter 1 - Overview

9
- Mounting
  11
- Dimensional Drawings
  12
- 12" Operator Interface Cutout Dimensions
  13
- Wiring
  14
- Electrical Installation
  14
- Pin out
  15
- Ancillary Items
  15
- Setup
  16
- Additional Features
  16
- Ethernet Connections
  16
- Instrument Start
  17
- Flash Card & Flash Card Reader
  17
- Operator Interface Screen Saver
  17
- Default Status Screen
  17
- Display
  17
- Menu
  18
- Chart
  18
- Chart Sub Menu
  19
- Recipe
  20
- Loops
  21
- Ack (Alarm Acknowledge)
  22
- Data Logging Using Flash Card
  22
Chapter 2 - Configuration

23
- Menu (Configuration)
  23
- Logs
  24
- Slave Communications Status
  25
- Load Tc/Auxiliary Analog Input
  25
- Manual Event Control
  25
- Shutdown
  26
- PID Loop Setup
  26
- Recipe Edit
  31
- Load T/C Configuration
  32
- Trend Chart Edit
  32
- Communications Setup
  34
- Slave Instrument Setup
  37
- Zone Assignments
  39
- Furnace Setup
  40
- Default Wait Limits
  42
- Alarm Setup
  42
- Relay Assignments
  44
- Analog Input Setup
  45
- Analog Output Setup
  48
- Alarm Polarity
  49
- Event Hold/Reset
  49
- Security
  50
- Curve Entry
  51
- Alternate PID Setup
  52
- Aux Analog Input Setup
  53
- Equipment Needed
  53
- Calibration
  55
- Configuration
  57
- A/I Module Offset Correction
  63
- PV Switching
  63
- Aux Setpoint Configuration
  63
- T/C Correction Curves
  64
- Generic Instruments
  64
- Tuning Assistant
  66
- Timer Setup
  67
- Instrument Calculation
  70
Chapter 3 - Configurator 2.0 Menus

73
- Slave Instruments
  73
- Auxiliary Analog Input
  73
- Manual Event Control
  74
- Pid Loop Setup
  74
- Event Run Program Setup
  79
- Zone/Load TC Setup
  80
- Port Setup
  80
- Slave Instrument Setup
  80
- Zone Assignments
  82
- Furnace Setup
  82
- Default Wait Limits
  85
- Alarm Setup
  85
- Thermocouple Check
  87
- Relay Assignments
  87
- Analog Input Setup
  88
- Analog Output Setup
  91
- Passcode and Alarm
  92
- Ip Address
  93
- Redundant Tc Setup
  93
- Event Control
  93
- Curve Entry
  94
- Alternate Pid Setup
  95
- Ssi Analog Input Setup
  96
- Ssi Configuration and Calibration
  96
- Overview
  96
- Equipment Needed
  96
- Notes
  96
- Calibrate Aux Analog Input
  97
- 9130 User Calibration
  99
- 9130 Full Calibration
  101
- A/I Module Offset Correction
  102
- Pv Switching
  102
- Aux Setpoint Configuration
  103
- Tc Extension Correction Curves
  103
- Generic Instrument Setups
  104
- Configure Generic Instruments
  105
- Configure IP Addresses
  105
- Configure Block Writes
  106
- Tuning Assistant
  106
- Instrument Calculation
  108
- Programmer Description
  111
- Opcodes
  111
- Wait
  125
- Wait up
  125
- Wait down
  126
- Wait in a Guaranteed Soak
  127
- Guarantee High Assignment
  128
- Guarantee Low Assignment
  129
Chapter 5 - Applications Information

130
- Default Values
  130
- Sample Event Assignments
  133
- Flash Card Management
  133
- Slave Instrument Mapping
  137
- Atmosphere Instruments
  137
- Temperature Instruments
  140
- Events Instruments
  145
- Sample 9130 Configuration
  148
- Sample 9130 Recipe
  186
- 9130 Analog Input Board Jumper Settings
  187
Appendix A - Wiring Diagram of Series 9130: Rs-232

189
Appendix B - Wiring Diagram of Series 9130: Rs-485

190
- Warranty
  191
- Revision History
  192

Advertisement

Advertisement

Related Products

Super Systems Categories

Measuring Instruments Temperature Controller

Oven

Oven Control Unit Controller

More Super Systems Manuals