User Manuals: Sourcetronic ST2829C LCR Measuring Bridge

Manuals and User Guides for Sourcetronic ST2829C LCR Measuring Bridge. We have 1 Sourcetronic ST2829C LCR Measuring Bridge manual available for free PDF download: Manual

Sourcetronic ST2829C Manual

Sourcetronic ST2829C Manual (119 pages)

LCR meter

Brand: Sourcetronic | Category: Measuring Instruments | Size: 4 MB

Table of Contents

Table of Contents
2
Fuse
7
Out of Box Audit
7
Power Connection
7
To Inspect the Package
7
Environment
8
Other Features
8
Use of Test Fixture
8
Warm-Up
8
Chapter 2 Introduction

10
- Introduction to Front Panel
  10
- Introduction to Rear Panel
  12
- Introduction to Display Zone
  13
- Main Menu Keys and Corresponding Displayed
  14
- Disp]
  14
- Setup]
  14
- System]
  14
- Basic Operation
  15
- Start the Instrument
  15
Chapter 3 Introduction to [DISP]

17
- Meas Display
  17
- Test Function
  18
- Test Range
  20
- Test Frequency
  20
- Test Level
  21
- DC Bias
  22
- Test Speed
  22
- Tools
  23
- Save LCR Test Result by U Disk
  24
- Bin No. Disp
  24
- Comparator Function
  25
- Bin Count Disp
  26
- Param
  27
- Nom
  27
- Bin
  27
- High/Low
  27
- Count
  27
- Aux
  27
- Out
  27
- List Sweep Disp
  28
- Sweep Mode
  29
- FREQ (Hz)
  29
- Cp[F] D[ ]
  29
- CMP (Compare)
  29
- TRACE Sweep>Page
  30
- Format
  30
- Scale
  31
- Read
  31
- Trace
  31
- Points
  31
- Trigger
  31
- Measure Setup
  32
- Trigger Mode
  34
- Auto Level Control Function
  34
- Bias Current Isolation Function
  35
- Average
  36
- Level Monitor Function
  36
- Delay Time
  37
- Output Impedance
  37
- Deviation Test Function
  37
- Correction
  39
- Open
  40
- Short
  41
- Load
  42
- Load Correction Test Function
  44
- Cable Length Selection
  44
- Single/ Multi Correction Mode
  44
- Limit Table
  45
- Swap Parameter
  45
- Limit Modes of Compare Function
  46
- Set Nominal Value of Tolerance Mode
  47
- Comparator Function ON/OFF
  47
- Auxiliary bin ON/OFF
  48
- High/Low
  49
- List Sweep Setup
  50
- Mode
  50
- Test Parameter
  50
- Sweep Parameter Setup
  51
- Trace Sweep Setup
  51
- Mode
  52
- Start
  53
- End
  53
- Coordination Range Setting
  53
Chapter 4 [SYSTEM] and <FILE MANAGE

54
- System Setup
  54
- Main Func
  54
- On Beepers
  54
- Pass Beep
  55
- Fail Beep
  55
- Language
  56
- Pass Word
  56
- BUS MODE (Reserved Function)
  57
- GPIB ADDR (Reserved Function)
  57
- Talk Only
  57
- Bias Src
  57
- Baud Rate
  58
- Data/Time
  58
- Lcr <File Manage
  59
- Setup File for Single-Group Component (*.STA)
  59
- U-Disk Manage Performance
  60
- Operation Steps for File Management
  60
Chapter 5 Execute LCR Operation and some Examples

63
Chapter 6 Performance and Test

73
- Test Function
  73
- Parameter and Symbol
  73
- Mathematical Operation
  73
- Equivalent Mode
  73
- Range
  73
- Trigger
  73
- Delay Time
  74
- Connection Modes of Test Terminals
  74
- Test Speed (Frequency>=10Khz)
  74
- Average
  74
- Display Digit
  74
- Test Signal
  74
- Test Signal Frequency
  74
- Signal Mode
  75
- Test Signal Level
  75
- Output Impedance
  75
- Monitor for Test Signal Level
  75
- Maximum Measurement Display Range
  75
- DC Bias Voltage Source
  76
- Measurement Accuracy
  76
- Accuracies of │Z│,│Y│, L, C, R, X, G, B
  76
- Accuracy of D
  76
- Accuracy of Q
  77
- Accuracy of Θ
  77
- Accuracy of G
  77
- Accuracy of Rp
  77
- The Accuracy of Rs
  78
- Accuracy Factor
  78
- Accuracy of DCR
  81
- Accuracy of Leakage Inductance Lk
  81
- Safety Requirement
  81
- Insulation Resistance
  82
- Insulation Intensity
  82
- Leakage Current
  82
- Electromagnetic Compatibility
  82
- Performance Test
  82
- Working Condition
  82
- The Used Instruments and Devices
  82
- Function Check
  83
- Test Signal Level
  83
- Frequency
  83
- Measurement Accuracy
  84
- Accuracy of C and D
  84
- Accuracy of L
  84
- Accuracy of Z
  84
- Accuracy of DCR
  85
Chapter 7 Command Reference

86
- Subsystem Commands for ST2829
  86
- Display Subsystem Commands
  86
- Frequency Subsystem Commands
  88
- Voltage Subsystem Commands
  89
- Current Subsystem Commands
  89
- Amplitude Subsystem Commands
  90
- Output Resister Subsystem Commands
  90
- Output Subsystem Commands
  90
- BIAS Subsystem Commands
  92
- Function Subsystem Commands
  93
- LIST Subsystem Commands
  97
- Aperture Subsystem Commands
  100
- Trigger Subsystem Commands
  101
- Fetch? Subsystem Commands
  102
- Correction Subsystem Commands
  104
- Comparator Subsystem Commands
  110

Advertisement

Advertisement

Related Products

Sourcetronic Categories

Measuring Instruments Test Equipment Inverter Multimeter DC Drives

More Sourcetronic Manuals