Sorensen HPD 60-5 Manuals

Manuals and User Guides for Sorensen HPD 60-5. We have 1 Sorensen HPD 60-5 manual available for free PDF download: Instruction Manual

Sorensen HPD 60-5 Instruction Manual

Sorensen HPD 60-5 Instruction Manual (46 pages)

Internal GPIB Interface

Brand: Sorensen | Category: Power Supply | Size: 3 MB

Table of Contents

About this Manual
4
Manual Changes
5
Table of Contents
6
Features and Specifications
9
Introduction to the GPIB Interface
9
Figure 1.1-1 Sample Configuration Using GPIB Interface
9
Features and Functions
10
Gpib Interface
10
Installation and Configuration
11
Introduction
11
Initial Inspection
11
Figure 2.2-1 Power Supply Front Panel (GPIB Interface Installed)
12
Figure 2.2-2 Power Supply Rear Panel (GPIB Interface Installed)
12
Jumper Selection
13
Led Indicators
13
Figure 2.2-3 GPIB Interface PCB for 60W and 300W Series Supplies
13
Basic Setup Procedure
14
Table 2.3-1 Setup Procedure
14
OVP Selection
14
IEEE-488 Primary Address Selection
15
Table 2.3-2 OVP Control Mode Selection
15
Table 2.3-3 IEEE-488 Primary Address Selection
15
Remote/Local Operation
16
Table 2.3-4 Remote/Local Mode Operation Selection
16
Table 2.3-5 Remote Mode Power on Conditions
16
Table 2.3-6 Local Mode Disable Jumper J95
17
IEEE-488 Controller Connection
18
Power on Service Request (PON SRQ)
18
User Signals
18
Connector J7 User Signals
18
Table 2.3-7 SRQ Enable Switch Selection
18
Table 2.4-1 J7 User Signal Connector
18
J7 Cable Connection
19
Figure 2.4-1 J7 User Cable with Ferrite Block
19
Operation
20
Introduction
20
GPIB Operation
20
Multiline Control Functions
20
Table 3.2-1 IEEE-488 Interface Upgrades Implemented
20
Device Clear
21
Device Trigger
21
Parallel Poll
21
Local Lockout
21
Power on Service Request (PON SRQ)
22
Serial Poll
22
Table 3.2-2 Serial Poll Status Register
22
Command Syntax
23
Command Format and Parameters
23
Table 3.3-1 Command Parameters
23
Command Strings
24
Command Terminators
24
Order
24
Command Summary
25
Table 3.4-1 Programming Commands
25
Table 3.4-2 Query Commands
25
Table 3.4-3 Calibration Commands
26
Table 3.4-4 Status Commands
26
Command Reference
27
Table 3.5-1 Command Reference
27
Accumulated Status, Status, and Fault Registers
33
Table 3.6-1 Status and Fault Registers
33
Error Codes
34
Table 3.7-1 Error Codes
34
Calibration
35
Introduction
35
Voltage Mode Calibration
35
Voltage Calibration Setup
35
Voltage Program Calibration Procedure
35
Figure 4.2-1 Voltage Calibration Setup
35
Voltage Readback Calibration Procedure
36
Current Mode Calibration
37
Current Calibration Setup
37
Current Program Calibration Procedure
37
Figure 4.3-1 Current Calibration Setup
37
Current Readback Calibration Procedure
38
Over Voltage Protection (OVP) Calibration
38
Maintenance
39
Introduction
39
Troubleshooting
39
Diagnostic Leds
39
Replaceable Parts
40
Parts Replacement and Modifications
40
Ordering Parts
40
Table 5.3-1 Replaceable Parts
40
Appendix A: Specifications
43

Advertisement

Advertisement

Related Products

Sorensen Categories

Power Supply

Power Supply Industrial Electrical Recording Equipment Controller

More Sorensen Manuals