User Manuals: Scientific SM6030A Transformer Tester

Manuals and User Guides for Scientific SM6030A Transformer Tester. We have 1 Scientific SM6030A Transformer Tester manual available for free PDF download: Operation Manual

Scientific SM6030A Operation Manual

Scientific SM6030A Operation Manual (188 pages)

Automatiic Transformer Test System

Brand: Scientific | Category: Test Equipment | Size: 3 MB

Table of Contents

Table of Contents
2
Chapter 1 Out of Box Audit

9
- To Inspect the Package
  9
- Power Connection
  9
- Fuse
  9
- Environment
  9
- Use of Test Fixture
  10
- Warm-Up
  10
- Other Features
  10
Chapter 2 Introduction

11
- Introduction to Front Panel
  11
- Introduction to Rear Panel
  12
- Introduction to Display Zone
  13
- Main Menu Keys and Corresponding Displayed
  14
- Disp]
  14
- Setup]
  15
- System Setup
  15
- Basic Operation
  16
- Start the Instrument
  16
Chapter 3 Introduction to [DISP]

17
- Meas Display
  17
- Test Function
  17
- Test Range
  20
- Test Frequency
  21
- Test Level
  22
- DC Bias
  22
- Test Speed
  23
- Tools
  23
- Use USB to Save LCR Test Results
  24
- Bin No. Disp
  25
- Comparator Function
  26
- Bin Count Disp
  26
- Param
  27
- Nom
  27
- Bin
  27
- High/Low
  27
- Count
  28
- Out
  28
- List Sweep Disp
  28
- Sweep Mode
  29
- FREQ (Hz)
  30
- Cp[:] D[:]
  30
- CMP (Compare)
  30
- Measure Setup
  30
- Trigger Mode
  31
- Auto Level Control Function
  32
- Average
  32
- Voltage/Current Level Monitor Function
  32
- Trigger Delay
  33
- Step Delay
  33
- Output Impedance
  34
- DCR Polarity
  34
- DC Resistance Range
  34
- DC Level
  34
- Deviation Test Function
  35
- Correction
  36
- Open
  37
- Short
  38
- Load
  39
- Load Correction Test Function
  41
- Cable Length Selection
  41
- Limit Table
  41
- Swap Parameter
  42
- Limit Modes of Compare Function
  42
- Set Nominal Value of Tolerance Mode
  43
- Comparator Function ON/OFF
  44
- Auxiliary bin ON/OFF
  44
- High/Low
  45
- List Sweep Setup
  46
- Mode
  46
- Test Parameter
  46
- Sweep Parameter Setup
  47
Chapter 4 [SYSTEM] and <FILE MANAGE

48
- System Setup
  48
- Main Func
  48
- Theme
  48
- Pass Beep
  49
- Fail Beep
  49
- Language
  50
- Pass Word
  50
- Bus Mode
  50
- Gpib Addr
  51
- Talk Only
  51
- Bias Src
  51
- Baud Rate
  52
- Data/Time
  52
- Lcr <File List
  52
- Setup File for Single-Group Component (*.STA)
  53
- U-Disk Manage Performance
  54
- Operation Steps for File Management
  54
Chapter 5 Execute LCR Operation and some Examples

57
Chapter 6 Transformer Stand Alone Test

65
- Circuit for Transformer Stand Alone Test
  65
- Some Parameters of Transformer
  65
- Capacitance Test between Transformer Windings
  65
- TRANS TEST SET> Interface
  65
- Delay
  66
- Bias
  67
- Mode
  67
- Setting Lx Test Conditions
  68
- Setting DCR Test Conditions
  68
- Test Frequency, Voltage and Switch
  68
- TRANS LIMIT SET> Interface
  69
- Lmt Mode
  69
- Parameter Column
  69
- TRANS MEAS DISP> Interface
  69
- Save Transformer Single-Group Test Result by U Disk
  70
Chapter 7 Transformer Auto Scanning Test

71
- Introduction to Scan Test Function
  71
- Install and Connect the Scanning Test System
  71
- Upper Panel of Scanning Box
  73
- Lower Panel of Scanning Box
  75
- HANDLER Interface
  75
- Timing Diagram of HANDLER Signal
  75
- Distribution and Connection Diagram for HANDLER
  75
- Example of Transformer
  77
- Transformer ID
  77
- Clear Ram
  78
- Transformer Pin Label
  78
- Handler Mode
  79
- Autotrig Delay
  80
- Pass Disp Time
  81
- Save Log as
  81
- Hdl Valid Time
  82
- Relay Act Time
  82
- Lk. Relay Dly
  83
- Dcr Relay Dly
  83
- Transformer ID
  83
- Primary Nums
  84
- Secondary Nums
  84
- Rescan Interval
  84
- Scan Disp Mode
  84
- Fail Rescan
  85
- Dcr Meas Delay
  85
- Dcr over Delay
  85
- Bias on Delay
  85
- Ignore Nom
  85
- Trigger Delay
  86
- Cylinder Ctrl
  86
- Allocate Pin to Fixture
  86
- Pin to Fixture
  86
- Pin Setup
  87
- Series Pin Short Setup
  89
- Paralell Pin Short Setup
  89
- TEST CONDITION> Interface
  90
- Frequency, Voltage, Switch and Scanning Sequence
  91
- Setting TURN Test Conditions
  91
- Setting Lx Test Conditions
  94
- Setting Lk Test Conditions
  98
- Setting CX Test Conditions
  99
- Setting Zx Test Conditions
  101
- Setting ACR Test Conditions
  102
- Setting DCR Test Conditions
  103
- Setting PS Test Conditions
  103
- Setting BL Test Conditions
  105
- Trans Scan Test
  106
- Display Zone
  107
- Function Key
  108
- PRI Page-Turning Function
  109
- File Manage
  109
- Operation Steps for File Manage
  110
- Stored File of SM6030A
  112
- Compatibility of Stored Files
  112
- Transformer Deviation-Deduction
  113
- Save Scan Test Results by U Disk
  116
- Statistic Page of Transformer Scan Test
  116
- Reset Statistic Count Value
  117
- Frequently Asked Questions and Answers in Transformer Scan Test
  117
- High & Low Limits
  117
- Measurement Item Loss
  117
- Measurement Interruption
  117
- Poor DCR Accuracy
  118
- Poor Lk Accuracy
  118
- Inaccurate Turn
  118
- Unstable Turn
  118
- Difference between the First and the Second Lx
  118
- Poor Stability of CX and Zx Open Test Data
  119
- DCR and PS Open Cannot Reach Infinite Large
  119
- User-Made Test Fixture
  119
- Use 1831-EXT1 to Make Test Fixture
  119
- Example of Using 1801-EXT11A(5.0)-B Pin Signal
  121
- Self-Check Function of Scanner Relay
  121
- Operation Steps for Scan Self-Check
  121
- Displayed Information on Screen
  122
- Detection Method for Relay Short
  123
- Relays Act Count
  123
- View Steps of Scan Box for <RELAYS ACT COUNT
  123
- Screen Display Information Description
  124
Chapter 8 Performance and Test

125
- Test Function
  125
- Parameter and Symbol
  125
- Test Combination
  125
- Mathematical Operation
  125
- Equivalent Mode
  125
- Range
  125
- Trigger
  126
- Delay Time
  126
- Connection Modes of Test Terminals
  126
- Test Speed (Frequency>=10Khz)
  126
- Average
  126
- Display Digit
  126
- Test Signal
  126
- Test Signal Frequency
  126
- Signal Mode
  127
- Test Signal Level
  127
- Output Impedance
  127
- Monitor for Test Signal Level
  127
- Maximum Measurement Display Range
  127
- DC Bias Voltage Source
  128
- Measurement Accuracy
  128
- Accuracies of │Z│,│Y│, L, C, R, X, G, B
  128
- Accuracy of D
  128
- Accuracy of Q
  129
- Accuracy of Θ
  129
- Accuracy of G
  129
- Accuracy of Rp
  129
- The Accuracy of Rs
  130
- Accuracy Factor
  130
- Accuracy of DCR
  133
- Lk Accuracy
  133
- Turns to Ratio Accuracy
  134
- Safety Requirement
  134
- Insulation Resistance
  134
- Insulation Intensity
  134
- Leakage Current
  134
- Electromagnetic Compatibility
  134
- Performance Test
  135
- Working Condition
  135
- The Used Instruments and Devices
  135
- Function Check
  136
- Test Signal Level
  136
- Frequency
  136
- Measurement Accuracy
  136
- Accuracy of C and D
  136
- Accuracy of L
  136
- Accuracy of Z
  137
- Accuracy of DCR
  137
Chapter 9 Command Reference

138
- Subsystem Commands for SM6030A
  138
- Display Subsystem Commands
  138
- Frequency Subsystem Commands
  140
- Voltage Subsystem Commands
  141
- Current Subsystem Commands
  141
- Amplitude Subsystem Commands
  141
- Output Resister Subsystem Commands
  142
- BIAS Subsystem Commands
  142
- Function Subsystem Commands
  144
- LIST Subsystem Commands
  147
- Aperture Subsystem Commands
  151
- Trigger Subsystem Commands
  152
- Fetch? Subsystem Commands
  153
- Correction Subsystem Commands
  156
- Comparator Subsystem Commands
  162
- Mass Memory Subsystem Commands
  166
- TRAN Subsystem Commands
  167
- GPIB Common Commands
  173
Chapter 10 The Description for Handler (Optional)

177
- Technical Description
  177
- The Operation Description
  177
- The Definition for the Signal Line
  177
- Electrical Feature
  184
- HANDLER Interface Board Circuit
  185
- Operation
  188

Advertisement

Advertisement

Related Products

Scientific Categories

Power Supply

Power Supply Measuring Instruments Test Equipment Laboratory Equipment Portable Generator

More Scientific Manuals