Radionics D6412 Manuals

Manuals and User Guides for Radionics D6412. We have 1 Radionics D6412 manual available for free PDF download: Installation Manual

Radionics D6412 Installation Manual

Radionics D6412 Installation Manual (76 pages)

Control/Communicator

Brand: Radionics | Category: Controller | Size: 2.02 MB

Table of Contents

Table of Contents
2
1 Introduction

7
2 Overview

10
- Specifications
  10
- Voltage Input
  10
- Current Requirements
  10
- Power Outputs
  10
- Battery Discharge/Recharge Schedule
  10
- Figure 1: System Configuration
  10
- Minimum Operating Voltage
  11
- SDI Bus (Data)
  11
- Telephone Connections
  11
- Environmental
  11
- Arming Stations
  11
- Compatible Enclosures
  11
- Compatible Accessories
  11
- Control/Communicator Configurations
  11
- SIA Control Panel Standard
  12
- Standard Features
  12
- Points
  12
- Areas and Accounts
  12
- Communicator
  12
- Command Centers
  13
- Keyswitch
  13
- Alarm Event Memory
  13
- Event Log
  13
- Emi/Lightning Transient Protection
  13
- Programming
  13
- Other Features
  13
- Table 3: Compatible Command Centers
  13
- Control/Communicator Assembly
  14
- Listings and Approvals
  14
3 Installation

15
- Before You Begin
  15
- Enclosure Options
  15
- Beginning the Installation
  15
- Mounting the Enclosure
  15
- Premises Wiring
  15
- Installing the Assembly
  16
- Connecting Earth Ground
  16
- Closing the Installer Switch
  16
- Figure 2: Enclosure Mounting
  16
- Finishing the Installation
  17
- Earth Ground and Installer Switch
  17
- Charge the Battery as You Finish
  17
- Install and Wire Detection Devices
  17
- Install Modules
  17
- Figure 3: Installer Switch
  17
- Make the Telephone Connections
  18
- Connect the On-Board Points and Command Centers
  18
- Power up
  18
- Programming the Panel
  18
- Check for Fire Alarm Verification
  18
- Testing the System
  18
4 Power Supply

19
- Primary Power
  19
- Primary (AC) Power Circuit
  19
- Installing the Transformer
  19
- Secondary Power
  19
- Secondary (DC) Power
  19
- Installing the Battery
  19
- Replacement
  19
- Battery Supervision
  20
- Battery Charging Circuit
  20
- Battery Discharge/Recharge Schedule
  20
- System Status LED
  20
- Figure 4: System Status LED
  20
- External Power Supply
  21
5 Power Outputs

21
- Circuit Protection
  21
- Available Power
  21
- Auxiliary Power
  21
- Installer's Keypad Connector
  21
- Alarm Power
  21
- Continuous Power Output
  21
- Continuous Current Draw
  21
- Output Programming
  22
- Figure 5: On-Board Outputs
  22
6 Telephone Connections

23
- Registration
  23
- Notification
  23
- Location
  23
- Phone Cord Connection
  23
- Figure 6: RJ31X/RJ38X Wiring
  23
- System Status LED (Red)
  24
- Dialing Format
  24
- Phone Line Fault
  24
- Called Party Disconnect
  24
- Figure 7: System Status LED
  24
- Communication Failure
  25
- Ground Start
  25
- Figure 8: Ground Start
  26
7 On-Board Sensor Loops

27
8 Off-Board Sensor Loops

30
9 On-Board Outputs

39
- Figure 23: On-Board Outputs
  39
10 Off-Board Outputs

40
11 Arming Devices

44
12 SDI Devices

48
13 Installer's Keypad and Installer Mode

52
- Installer's Keypad Connector
  52
- Figure 39: D9533 DB9 Connector Layout
  52
- Figure 40: Installer's Keypad
  52
- Entering the Installer Mode
  53
- Installer's Passcode
  53
- Service Start/Service End Reports
  53
- Installer's Menu
  53
- Press [1] for Bell Test
  53
- Press [2] for Strobe Test
  53
- Press [3] for Battery Test
  53
- Figure 41: Installer Switch
  53
- Press [4] for Test Report
  54
- Press [5] for Point Status
  54
- Press [6] for Output Test
  54
- Press [7] for RF Menu
  54
- Adding RF ID Codes
  54
- Figure 42: Adding RF ID Codes Menu Display
  54
- Figure 43: RF ID Code Display
  54
- Testing RF Devices
  55
- Figure 44: Test RF Devices Display
  55
- Figure 45: RF Device Test Status Display
  55
- Viewing/Removing RF ID Codes
  56
- Press [8] for Keypad Program
  56
- Press [9] Program Key
  56
- Figure 46: RF ID Code Display
  56
- Exiting the Installer's Menu
  57
- Figure 47: PK32 to D6412 Connections
  57
- Press [0] Call for Service Details
  58
14 Installation Label

59
15 Quick Reference Terminal Description

60
16 Troubleshooting

61
Appendix A: Approved Applications Compliance Guide

64
Appendix A: System Chart

65
Appendix A: System Wiring Diagrams, Issue a

66
Appendix A: Current Rating Chart for Standby Battery Calculations

67
Appendix A: Standby Battery Requirements

68
Appendix A: Standby Battery Calculation for NFPA 72 Fire Alarm Applications

68
Appendix B: SDI Address Chart

69
Glossary

70
Index

73

Advertisement

Advertisement

Related Products

Radionics Categories

Security System Control Panel Control Systems Keypad Fire Alarms

More Radionics Manuals