Pro Spot Exocut PR-30P Manuals

Manuals and User Guides for Pro Spot Exocut PR-30P. We have 1 Pro Spot Exocut PR-30P manual available for free PDF download: Manual

Pro Spot Exocut PR-30P Manual (82 pages)

Plasma Cutting and Gouging System

Brand: Pro Spot | Category: Welding System | Size: 8 MB

Table of Contents
9
Electromagnetic Compatibility (EMC
13
Installation and Use
13
Assessment of Area
13
Methods of Reducing Emissions
13
Mains Supply
13
Maintenance of Cutting Equipment
14
Cutting Cables
14
Equipotential Bonding
14
Earthing of the Workpiece
14
Screening and Shielding
14
Warranty
15
Attention
15
General
15
Patent Indemnity
16
Limitation of Liability
16
National and Local Codes
16
Liability Cap
16
Insurance
16
Transfer of Rights
16
Specifications
17
Safety Information
17
System Description
17
Power Supply Dimensions
18
System Weights
18
Pro Spot System Ratings
19
Torch Dimensions
20
Torch Weight
20
Cutting Specifications
20
Symbols and Marks
21
Noise Levels
22
IEC Symbols
22
Power Supply Setup
23
Unpack the Plasma System
23
Claims
23
System Contents
24
Position the Plasma System
25
Prepare the Electrical Power
25
Voltage Configurations
26
Requirements for Grounding
27
Power Cord Considerations
27
Extension Cord Recommendations
28
Generator Recommendations
28
Prepare the Gas Supply
29
Connect the Gas Supply
29
Additional Gas Filtration
30
Torch Setup
31
Introduction
31
Hand Torch Components
31
Consumable Life
32
Choose the Consumables
32
Using the Cut Charts
34
General-Purpose (Standard) Consumables
35
240 V / 30 a Cutting
36
Thincut Consumables
37
120 V / 25 a Cutting
38
120 V / 30 a Cutting
39
Gouging Consumables
40
Operation
41
Controls and Indicators
41
Rear Controls
41
Front Controls and Leds
42
Operate the Plasma System
43
Connect the Electrical Power and Gas Supply
43
Install the Consumables
44
Attach the Ground Clamp
46
Power on the System
46
Adjust the Gas Pressure and Output Current
46
Operating the System on a 120 V, 15 a Circuit
47
Operating the System on a 120 V, 20 a Circuit
47
Operating the System on a 240 V, 20 a Circuit
47
Check the Indicator Leds
48
Verify the System Is Ready
48
Understand Duty-Cycle Limitations
48
System Operation Guidelines
49
Hand Torch Operation
50
Safety Catch Operation
51
Hand Torch Cutting Guidelines
52
Recommendations for Cutting at 120 V
53
Edge Start on a Workpiece
53
Pierce a Workpiece
55
Gouge a Workpiece
56
General Gouging
56
Remove a Spot Weld
58
Varying the Gouge Profile
60
Common Hand-Cutting Faults
61
Minimizing Dross
61
Maintenance and Troubleshooting
63
Perform Routine Maintenance
63
Inspect the Consumables
65
Basic Troubleshooting
66
Maintenance Procedures
69
Replace the Air Filter Element and Air Filter Bowl
69
Remove the Power Supply Cover and Handle
69
Remove the Old Air Filter Element and Air Filter Bowl
70
Install the New Air Filter Element and Air Filter Bowl
71
Put the Power Supply Cover and Handle Back in Place
72
Parts
75
Power Supply Parts
76
Exterior, Front
76
Exterior, Rear
77
Air Filter/Regulator with Pressure Switch Assembly (Interior, Fan Side)
78
Hand Torch Consumables
79
General-Purpose (Standard) Consumables
79

Pro Spot Categories

Welding System Rivet Tools Heater Welding Accessories

More Pro Spot Manuals

Pro Spot Exocut PR-30P Manuals

Pro Spot Exocut PR-30P Manual (82 pages)

Table of Contents

Related Products

Pro Spot Categories