Sign In
Upload
Manuals
Brands
Novanta Manuals
Control Unit
JADAK THINGMAGIC M7E-HECTO
Novanta JADAK THINGMAGIC M7E-HECTO Manuals
Manuals and User Guides for Novanta JADAK THINGMAGIC M7E-HECTO. We have
1
Novanta JADAK THINGMAGIC M7E-HECTO manual available for free PDF download: User Manual
Novanta JADAK THINGMAGIC M7E-HECTO User Manual (55 pages)
Brand:
Novanta
| Category:
Control Unit
| Size: 1 MB
Table of Contents
Copyright Information
2
Revision History
2
Table of Contents
3
Introduction
8
Release Notes
8
Hardware Overview
9
Hardware Interfaces
9
Module Pin-Out
9
Figure 1: Module Pinout with Drill Drawing Bottom View
9
Table 1: Module Pinout Definition
10
Antenna Connections
11
Voltage and Current Limits
11
Control Signal Specification
11
Table 2: Voltage and Current Limits
11
General Purpose Input/Output (GPIO)
12
Table 3: Receiver Baud Rate Tolerance
12
RUN Line
13
DC Power Requirements
13
RF Power Output Impact on DC Input Current and Power
13
Figure 2: Current Draw Vs. DC Voltage and RF Output Level
14
Figure 3: Module Output Power Vs. Module Voltage
14
Power Supply Ripple
15
Idle DC Power Consumption
15
Power Consumption
15
Table 4: Power Modes and Power Consumption
15
RF Characteristics
16
RF Output Power
16
Receiver Adjacent Channel Rejection
16
Environmental Specifications
16
Thermal Considerations
16
Thermal Management
16
Electro-Static Discharge (ESD) Specification
17
Shock and Vibration
17
Authorized Antennas
17
FCC Modular Certification Considerations
18
Table 5: Authorized Antennas
18
Physical Dimensions
19
Module Dimensions
19
Table 6: Module Dimensions
19
Figure 5: Mechanical Drawing with Module Dimensions
19
Tape-And-Reel Dimensions
20
Figure 6: Tape and Reel Drawing
20
SMT Reflow Profile
21
Hardware Integration
21
Landing Pads
21
Figure 7: SMT Reflow Profile Plot
21
Module Carrier Board
22
Figure 8: Landing Pads and Heat Sync Areas
22
Table 7: Pinout of 15-Pin Connector on Carrier Board
23
Figure 9: Carrier Board
23
Figure 10: Carrier Board Schematic
24
Carrier Board Heat Sinking
25
Firmware Overview
25
Bootloader
25
Figure 11: Carrier Board Heat Spreader
25
Application Firmware
26
Programming the Thingmagic Module
26
Upgrading the Thingmagic Module Firmware
26
Verifying Application Firmware Image
26
Custom On-Reader Applications
26
Serial Communication Protocol
26
Host-To-Reader Communication
26
Reader-To-Host Communication
27
CCITT CRC-16 Calculation
27
Regulatory Support
27
Supported Regions
27
Table 8: Supported Regions
27
Frequency Setting
29
Frequency Units
29
Table 9: Regional Frequency Specifications
29
Frequency Hop Table
30
Support for Set/Get Quantization Value and Minimum Frequency
30
Protocol Support
31
Gen2 Protocol Configuration Options
31
Supported Gen2 Functionality
31
Table 10: Gen2 Protocol Supported Combinations
31
Antenna Port
32
Using a Multiplexer
32
GPIO State to Logical Antenna Mapping
32
Table 11: Standard Supported GEN2 Functions
32
Port Power and Settling Time
33
Tag Handling
33
Tag Buffer
33
Table 12: Logical Antenna Mapping
33
Table 13: Tag Buffer Fields
33
Tag Streaming/Continuous Reading
34
Tag Read Meta Data
34
Power Management
35
Power Modes
36
Performance Characteristics
36
Event Response Times
36
Table 14: Event Response Times
36
Module Specifications
37
Compliance and IP Notices
38
Communication Regulation Information
38
Federal Communication Commission (FCC) Interference Statement
38
ISED Canada
39
Authorized Antennas
40
EU Compliance
40
10.3.2. EU Authorized Antennas
40
Appendix A: Error Messages
41
Common Error Messages
41
Table 15: Common Fault Errors
41
Table 16: Bootloader Fault Errors
42
Table 17: Protocol Fault Errors
43
Table 18: Analog Hardware Abstraction Layer Fault Errors
46
Table 19: Tag ID Buffer Fault Errors
47
Table 20: System Fault Errors
47
Appendix B: Dev Kit
48
Dev Kit Hardware
48
Setting up the Development Kit
49
Connecting the Antenna
49
Powering up and Connecting to a PC
49
Dev Kit USB Interface USB/RS232
49
Development Kit Jumpers
50
Development Kit Schematics
51
Demo Application
51
Notice on Restricted Use of the Development Kit
51
Appendix C: Environmental Considerations
52
ESD Damage Overview
52
Identifying ESD as the Cause of Damaged Readers
52
Common Installation Best Practices
53
Raising the ESD Threshold
53
Further ESD Protection for Reduced RF Power Applications
54
Variables Affecting Performance
54
Environmental
54
Tag Considerations
54
Antenna Considerations
54
Multiple Readers
55
Advertisement
Advertisement
Related Products
Novanta JADAK THINGMAGIC M7E-MEGA
Novanta JADAK THINGMAGIC M7E-TERA
Novanta MOVIA
Novanta ventus with mpc6000
Novanta JADAK ThingMagic M7E-PICO
Novanta JADAK ThingMagic M7E-DEKA
Novanta MPC3000
Novanta NEMA 23
Novanta NEMA 34
Novanta Categories
Measuring Instruments
Industrial Equipment
Engine
Medical Equipment
Control Unit
More Novanta Manuals
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL