Nemic-Lambda TDK-Lambda Genesys GEN12.5-60 Manuals

Manuals and User Guides for Nemic-Lambda TDK-Lambda Genesys GEN12.5-60. We have 1 Nemic-Lambda TDK-Lambda Genesys GEN12.5-60 manual available for free PDF download: Manual

Nemic-Lambda TDK-Lambda Genesys GEN12.5-60 Manual

Nemic-Lambda TDK-Lambda Genesys GEN12.5-60 Manual (74 pages)

Programmable Regulated Power Supplies

Brand: Nemic-Lambda | Category: Power Supply | Size: 2 MB

Table of Contents

Table of Contents
3
Chapter 1 General Information

12
- Introduction
  12
- General Description
  12
- Features and Options
  12
- Multiple Output Power System
  13
- Control Via the Serial Communication Port
  13
- Analog Voltage Programming and Monitoring
  13
- Parallel Operation
  13
- Output Connections
  13
- Cooling and Mechanical Construction
  14
- Accessories
  14
- General
  14
- Serial Link Cable
  14
- Misc. Hardware
  14
- AC Cables
  14
- Serial Port Cables
  14
Chapter 2 Specifications

15
- Output Rating
  15
- Input Characteristics
  15
- Constant Voltage Mode
  15
- Constant Current Mode
  15
- Analog Programming and Monitoring
  15
- Programming and Readback
  16
- Protective Functions
  16
- Front Panel
  16
- Environmental Conditions
  16
- Mechanical
  16
- Safety/Emc
  16
- Supplemental Characteristics
  17
- Outline Drawings
  18
Chapter 3 Installation

19
- General
  19
- Preparation for Use
  19
- Initial Inspection
  19
- Rack Mounting
  19
- To Install the Power Supply in a Rack
  19
- Rack Mount Slides
  20
- Location Mounting and Cooling
  20
- Ac Source Requirements
  20
- Ac Input Power Connection
  20
- AC Input Connector, 1500W Models
  21
- AC Input Connector, 750W Models
  21
- AC Input Cord
  21
- AC Input Wire Connection, 1500W Models
  21
- Turn-On Checkout Procedure
  22
- General
  22
- Prior to Operation
  22
- Constant Voltage Check
  23
- Constant Current Check
  23
- OVP Check
  23
- UVL Check
  23
- Foldback Check
  24
- Address Setting
  24
- Baud Rate Setting
  24
- Connecting the Load
  24
- Load Wiring
  24
- Current Carrying Capacity
  24
- Wire Termination
  25
- Noise and Impedance Effects
  26
- Inductive Loads
  26
- Making the Load Connections
  26
- Connecting Single Loads, Local Sensing (Default)
  29
- Connecting Single Loads, Remote Sensing
  29
- Connecting Multiple Loads, Radial Distribution Method
  29
- Multiple Loads Connection with Distribution Terminals
  30
- Grounding Outputs
  30
- Local and Remote Sensing
  31
- Local Sensing
  31
- Remote Sensing
  32
- J2 Sense Connector Technical Information
  32
- Repackaging for Shipment
  32
Chapter 4 Front and Rear Panel Controls and Connectors

33
- Introduction
  33
- Front Panel Controls and Indicators
  33
- Rear Panel
  35
- Rear Panel Sw1 Setup Switch
  36
- SW1 Positions Functions
  37
- Resetting the Switch
  37
- Rear Panel J1 Programming and Monitoring Connector
  38
- Making J1 Connections
  38
Chapter 5 Local Operation

40
- Introduction
  40
- Standard Operation
  40
- Constant Voltage Mode
  40
- Constant Current Operation
  40
- Automatic Crossover
  41
- Over Voltage Protection (Ovp)
  41
- Setting the OVP Level
  41
- Activated OVP Protection Indications
  41
- Resetting the OVP Circuit
  41
- Under Voltage Limit (Uvl)
  42
- Setting the UVL Level
  42
- Foldback Protection
  42
- Setting the Foldback Protection
  42
- Resetting Activated Foldback Protection
  42
- Output On/Off Control
  42
- Output Shut-Off (So) Control Via Rear Panel J1 Connector
  42
- Enable/Disable Control Via Rear Panel J1 Connector
  43
- CV/CC Signal
  43
- Ps_Ok Signal
  43
- Safe Start and Auto-Restart Modes
  44
- Automatic Start Mode
  44
- Safe Start Mode
  44
- Over Temperature Protection (Otp)
  44
- Last Setting Memory
  44
- Series Operation
  44
- Series Connection for Increased Output Voltage
  45
- Series Connection for Positive and Negative Output Voltage
  46
- Parallel Operation
  47
- Basic Parallel Operation
  47
- Advanced Parallel Operation
  47
- Daisy-Chain Connection
  49
- Front Panel Locking
  49
- Unlocked Front Panel
  49
- Locked Front Panel
  49
Chapter 6 Remote Analog Programming

50
Chapter 7 Rs232 & Rs485 Remote Control

54
- Introduction
  54
- Configuration
  54
- Default Setting
  54
- Address Setting
  54
- RS232 or RS485 Selection
  54
- Baud Rate Setting
  54
- Setting the Unit into Remote or Local Mode
  54
- RS232/458 Port at Local Mode
  55
- Front Panel in Remote Mode
  55
- Rear Panel Rs232/485 Connector
  55
- Connecting Power Supplies to Rs232 or Rs485 Bus
  56
- Single Power Supply
  56
- Multi Power Supplies Connection to RS232 or RS485 Bus
  57
- Communication Interface Protocol
  57
- Data Format
  57
- Addressing
  57
- End of Message
  57
- Command Repeat
  57
- Checksum
  57
- Acknowledge
  57
- Error Message
  58
- Backspace
  58
- Error Messages
  58
- Command Set Description
  58
- General Guides
  58
- Command Set Categories
  58
- Initialization Control Commands
  59
- ID Control Commands
  59
- Output Control Commands
  59
- Global Output Commands
  61
- Status Control Commands
  62
- Status, Error and Srq Registers
  63
- General
  63
- Conditional Registers
  63
- Service Request: Enabled and Event Registers
  64
- Serial Communication Test Set-Up
  67
Chapter 8 Isolated Analog Programming Option

68

Advertisement

Advertisement

Related Products

Nemic-Lambda Categories

Power Supply

More Nemic-Lambda Manuals