Motion computing 002-15-0010 Manuals

Table of Contents

2

1 Base with Power Supply Shroud Installed

4

Remove the Plastic Shroud that Covers the Power Supply
4

2 Column Assembly

4

3 Installing the Work Surface and Drawer

9

4 Assemble the Cpu/Monitor Vesa Mount Assembly

13

Attach Metal Spacers to the Front Cpu Vesa Mount Plate Corners
13
Place Nylon Spacers over the Monitor Vesa Mount Plate Threaded Inserts Where Arrows Indicate
13
Insert Screws through the Front CPU VESA Mount Plate Hole and through the Nylon Spacers, Threading Them into the Monitor VESA Mount Plate Threaded Inserts
14
Attach the Flush Tilting Vesa Mount Bracket to the Back Cpu Vesa Mount Plate
14
Place the Media Wave Computer Onto the Front CPU VESA Mount Plate, Evenly Spaced between the Metal Spacers and Connectors Facing down
14
Attach the Back CPU VESA Mount Plate to the Front CPU VESA Mount Plate, Using the Threaded Metal Spacers Attached to the Front Plate
15

5 Install the Monitor/Cpu Mount Assembly by Sliding the Flush Tilting Vesa Mount Bracket into the Front of the Column Rail

15

Position the Vesa Mount Bracket about One Inch from the Top of the Column Rail and Secure by Tightening the Set Screws
16

7 Assemble the Mounting Plate and Battery Gauge

16

6 Assemble the Battery Gauge Housing

16

8 Plug the Rj45 Battery Gauge Cable into the Jack, through the Hole in the Back of the Battery Gauge Housing

19

9 Attach the Battery Gauge Mount Plate to the Back Cpu Vesa Mount Plate17

20

10 Plug in and Secure Monitor Cables

21

11 Plug in and Secure Computer Cables

21

12 Dress the Cables at the Monitor and Cpu Using Corrugated Cable Wrap, Securing with Cable Ties

22

13 Pull the Excess Cable Length to the Bottom of the Column

22

14 Dress the Cables at the Bottom of the Column Using Corrugated Cable Wrap, Securing with Cable Ties, and Pulling the Excess Cable Length into the Sheet Metal Base

23

15 Install Batteries with Terminal Pointing Out. if the Batteries Are Turned In, the Thermal Sensors will Read Incorrectly

24

16 The Unpainted Side of the Thermal Sensor Must be in Contact with the Battery Post

25

17 Make Sure Battery Connections Are Tight on both Batteries

25

18 Reinstall the Shroud and Column Top Plate

26

Motion Computing 002-15-0010 Manuals

Motion Computing 002-15-0010 Installation And Assembly Manual (26 pages)

Table of Contents

1 Base with Power Supply Shroud Installed

2 Column Assembly

3 Installing the Work Surface and Drawer

4 Assemble the Cpu/Monitor Vesa Mount Assembly

5 Install the Monitor/Cpu Mount Assembly by Sliding the Flush Tilting Vesa Mount Bracket into the Front of the Column Rail

7 Assemble the Mounting Plate and Battery Gauge

6 Assemble the Battery Gauge Housing

8 Plug the Rj45 Battery Gauge Cable into the Jack, through the Hole in the Back of the Battery Gauge Housing

9 Attach the Battery Gauge Mount Plate to the Back Cpu Vesa Mount Plate17

10 Plug in and Secure Monitor Cables

11 Plug in and Secure Computer Cables

12 Dress the Cables at the Monitor and Cpu Using Corrugated Cable Wrap, Securing with Cable Ties

13 Pull the Excess Cable Length to the Bottom of the Column

14 Dress the Cables at the Bottom of the Column Using Corrugated Cable Wrap, Securing with Cable Ties, and Pulling the Excess Cable Length into the Sheet Metal Base

15 Install Batteries with Terminal Pointing Out. if the Batteries Are Turned In, the Thermal Sensors will Read Incorrectly

16 The Unpainted Side of the Thermal Sensor Must be in Contact with the Battery Post

17 Make Sure Battery Connections Are Tight on both Batteries

18 Reinstall the Shroud and Column Top Plate

Related Products

Motion Computing Categories