Lehigh E-Flex EFRP-08 Relay Panel Manuals

Manuals and User Guides for Lehigh E-Flex EFRP-08 Relay Panel. We have 1 Lehigh E-Flex EFRP-08 Relay Panel manual available for free PDF download: Installation And User Manual

Lehigh E-Flex EFRP-08 Installation And User Manual

Lehigh E-Flex EFRP-08 Installation And User Manual (43 pages)

Brand: Lehigh | Category: Relays | Size: 2 MB

Table of Contents

Table of Contents
4
Introduction
9
- Features and Specification
  9
- Software Version
  9
- Glossary of Terms
  10
- Codes/Standards
  11
  - Safeguards
    11
  - Warnings and Notices
    11
Installation
12
- Shipment Inspection
  12
- Mounting
  12
- Circuit Breaker Protection
  12
- Terminations and Conduit Access
  12
- Wiring Requirements
  13
- High Voltage Wiring
  13
  - Feed-Through Example - 4-Circuits, Individual Feeds
    14
  - Feed-Through Example - 4-Circuits, Normal/Emergency, 120V and 277V Feeds
    15
- Low Voltage Wiring
  16
  - Low Voltage Side Diagram
    16
  - Input Banks - Occupancy, Daylight, Contact Closure, and Capt
    17
    
    Demand Response/Timeclock/Emergency Inputs
    17
    
    0-10V Outputs
    18
    
    DMX Input
    18
    
    E-Flexnet
    18
- Controller Power Load Capability
  19
  - Controller Load Capability
    19
  - Input Device Unit Loads
    19
- Switch Configuration
  19
  - SW1 - Daylight Sensor Inputs
    19
  - SW2 - Occupancy Sensor Inputs
    19
  - SW5 - Flexnet Termination
    20
  - SW6 - DMX Termination
    20
  - Emergency Input
    20
    
    Emergency Enable/Disable (EMERG-J12)
    20
Power up and Configuration
21
- Pre-Check
  21
- Power up
  21
User Interface
22
- Menu Navigation
  22
- Input Programming
  23
  - Occupancy Inputs
    23
    
    Navigate to Occx Menu
    23
    
    Set Mode
    23
    
    Set Input Polarity
    23
    
    Assign Zones to Occupancy Input
    24
    
    Set Occupied Preset
    24
    
    Set Un-Occupied Preset
    24
  - Daylight Sensor Inputs
    25
    
    Navigate to Dayx Menu
    25
    
    Set Input Polarity
    25
    
    Assign a Zone to Daylight Sensor Input
    25
    
    Secondary Daylight Zone Adjustment
    25
  - Contact Closure Inputs
    26
    
    Navigate to CCIX Menu
    26
    
    Set Input Polarity
    26
    
    Set Contact Closure Mode
    26
    
    Assign Zones to Contact Closure Input
    27
    
    Set Contact Closure Response Preset
    27
  - Capt Station Inputs
    27
    
    Navigate to Capx Menu
    27
    
    Assign Zones to Capt Input
    27
    
    Set Capt Input Preset for 5-Button Station
    28
- Emergency Input Programming
  29
  - Assign Zones to Emergency Input
    29
  - Set Emergency Zone Levels
    29
- Timeclock/Demand Response Contact Closure Input Programming
  29
- DMX Setup
  32
- Load Setup
  34
  - Set Load Type
    34
  - Set Low End Trim and Relay Cutoff
    34
  - Set High End Trim
    35
- Preset Edit
  36
- Control/Test
  37
  - Navigate to Control Menu
    37
  - Clear Memory
    37
  - DMX Loss Behavior
    37
  - Relay Test
    38
  - Ramp Test
    38
  - Relay Override
    38
  - Device ID
    39
  - DASC - Daylight Scaler, Primary/Secondary Daylight Zone Adjustment
    39
Default Configuration
40
- Input Assignments
  40
  - Occupancy
    40
  - Daylight
    40
  - Contact Closure
    40
  - Capt
    41
  - Emergency
    41
  - Timeclock
    41
- Preset Levels
  41
- DMX Addressing and Zone Assignment
  41
- Load Setup
  41
- DMX Loss Behavior
  41
RDM Implementation
42
Blank Configuration Chart
43

Advertisement

Advertisement

Related Products

Lehigh Categories

Control Systems Controller Relays Receiver Gateway

More Lehigh Manuals