Kinco FD5 Series Manuals

Manuals and User Guides for Kinco FD5 Series. We have 2 Kinco FD5 Series manuals available for free PDF download: Manual, User Manual

Kinco FD5 Series Manual (206 pages)

AC servo system

Brand: Kinco | Category: Servo Drives | Size: 7 MB

Table of Contents
4
Chapter 1 Servo System Model and Configuration Description

8
Chapter 2 Servo System Installation Requirements and Notes

14
- Installation of Drive
  14
- Installation Requirement
  14
- Installation Distance and Direction
  16
- Drive Usage Requirements
  18
- Servo Motor Installation
  20
- Installation Requirements
  20
- Environment Conditions
  21
- Precautions
  22
Chapter 3 Installation and Wiring

25
- Drive Description
  25
- External System Connection
  26
- Wiring Connection Mode
  29
- Drive Anti-Interference Measurements
  30
- DC Bus
  32
- RS232 Serial Port
  33
- External Input and Output Connection（X1
  34
- Digital Signal Input
  38
- Digital Signal Output
  38
- Pulse Command Input
  40
- Brake Connection
  41
- Encoder Input（X2
  43
- Power Port（X3
  44
- Communication Port Input（X4
  44
Chapter 4 Controller Setup with LED Panel

46
- Panel Operation
  46
- Panel Menu Structure and Navigation
  47
- Easy Use Function
  48
- Setup Process with Easy Use Function
  48
- Flowchart and Description of the EASY Menu
  50
- Flowchart and Description of the Tune Menu
  54
- Reasons for the Failure of Tunning
  57
- Tuning Case
  58
- Jog Mode（Test Run
  60
- Error History（F007
  60
Chapter5 Kincoservo +, User Guide

62
- Getting Started
  62
- Language
  62
- Open and Saving Project Files
  62
- Starting Communication
  63
- Node ID and Baud Rate
  63
- Objects (Add，Delete，Help)
  63
- Init Save Reboot
  64
- Firmware Update
  64
- Read/Write Controller Configuration
  65
- Read Setting from Controller
  65
- Write Setting to Controller
  66
- Digital IO Function
  67
- Digital Input
  67
- Digital Outputs
  70
- Fast Capture
  71
- Scope
  73
- Error Display and Error History
  75
Chapter 6 Operation Modes and Control Modes

79
- General Steps for Starting a Control Mode
  79
- Step1: Wiring
  79
- Step 2: IO Function Configuration
  79
- Step 3: Set Necessary Parameters
  81
- Step 4: Save and Reboot
  85
- Step 5: Start Operation
  85
- Velocity Mode (-3, 3)
  85
- DIN Speed Mode
  86
- Torque Mode(4)
  88
- Position Mode(1)
  89
- DIN Introduction to Location Position
  90
- Position Flow Mode
  92
- Pulse Mode (-4)
  97
- Pulse Mode Setting Steps
  98
- Other Function
  100
- Electronic Gear Ratio Switching (Expert Mode)
  101
- Master-Slave Mode
  102
- Full Closed Loop Mode
  103
- Full Closed Loop Control Operation Steps
  106
- Homing Mode(6)
  108
- Other Functions
  116
- Limit Function
  116
- Motor Brake Control
  117
- Stop Mode Control
  120
- Multi-Tune Encoder Setting
  122
Chapter7:Tuning of The Servo System Control

127
- Auto-Tuning
  127
- Auto-Tuning Test Operation Method
  128
- Parameters for Auto-Tuning
  128
- Start of Auto-Tuning
  128
- Problems and Adjustments with Auto-Tuning
  129
- Adjustment after Auto-Tuning
  129
- Manual Tuning
  130
- Tuning of the Velocity Loop
  130
- Tuning of the Position Loop
  136
- Gain Switch (Pro Mode)
  139
- Gain Switching Method
  141
- Other Factors Affecting Performance
  142
Chapter 8 Alarm Investigation

142
Chapter 9 List of FD5 Motor Controller Parameters

148
- F001
  149
- F002
  151
- F003
  152
- F004
  154
- F005
  155
Chapter 10 Communication

157
- RS232 Wiring
  157
- RS232 Hardware Port
  157
- RS232 Communication Cable
  157
- RS232 Transfer Protocol
  157
- RS232 Data Protocol
  158
- RS485 Communication
  163
- RS485 Hardware Wiring
  163
- RS485 Communication Parameters
  164
- MODBUS RTU Communication Protocol
  165
- Communication Troubleshooting Measures
  166
- Canopen Bus Communication
  168
- Canopen Bus Communication Hardware Description
  168
- Canopen Bus Communication Software Description
  169
- Canopen Bus Communication Settings
  183
- Interpolation Mode Based on Canopen
  185
Appendix 1: Braking Resistor Selection

187
Appendix II: List of Common Object Parameters

188
- Mode and Control（0X6040
  188
- Measurement Data
  190
- Target（0X607A
  190
- Multi-Segment Position/Multi-Segment Velocity（0X2020
  192
- Performance Object（0X6065
  194
- Homing Control（0X6098
  195
- Velocity Loop Parameters（0X60F9
  195
- Position Loop（0X60Fb
  197
- Input/Output Port Parameter（0X2010
  198
- Pulse Input Parameters（0X2508
  201
- Parameters for Storage（0X2Ff0
  201
- Error Code（0X2601
  203
- Stop Mode
  204
- Other Parameter
  205

Kinco FD5 Series User Manual (148 pages)

AC servo system

Brand: Kinco | Category: Servo Drives | Size: 12 MB

Confirmation
2
Preface and Product Confirmation
2
Identifications Description
3
Manual Edition Record
3
Other Identifications
3
Content
4
Table of Contents
4
Chapter 1 Servo System Model and Configuration Description

9
Chapter 2 Servo System Installation Requirements and Notes

12
- Driver Installation
  12
- Installation Dimension
  12
- Installation Distance and Direction
  14
- Drive Requirements
  16
- Servo Motor Installation
  17
- Installation Requirements
  17
- Environment Conditions
  18
- Caution
  18
- Motor Torque-Speed Characteristic Curve
  19
Chapter 3 Servo System Interface and Wiring

22
- Drive Description
  22
- External System Connection
  23
- Wiring Connection Description
  25
- Drive EMC Configuration Description
  25
- Overload Protection of Servo
  28
- Common DC Bus
  30
- RS232 Serial Port
  31
- External Input and Output Connection（X1
  32
- Digital Signal Input
  35
- Digital Signal Output
  35
- Pulse Instruction Input
  36
- Brake Connection
  37
- Encoder Input（X2
  38
- Power Port（X3
  39
- Bus Communication Interface（X4
  39
Chapter 4 Digital Panel Operation

41
- Panel Operation
  41
- Panel Operation Instructions
  42
- Easy Use Function
  42
- Easy Use Operation Step
  42
- EASY Operation Flowchart
  44
- Tune Operation Flow Chart
  47
- Reasons for the Failure of Tunning
  49
- Tuning Case
  50
- Jog Mode（Test Run
  51
- Error History（F007
  51
Chapter5 Kincoservo + User Guide

52
- Getting Started
  52
- Language
  52
- Open and Saving Project Files
  52
- Starting Communication
  52
- Node ID and Baud Rate
  53
- Objects (Add，Delete，Help)
  53
- Init Save Reboot
  53
- Firmware Update
  54
- Read/Write Controller Configuration
  55
- Read Setting from Controller
  55
- Write Setting to Controller
  55
- Digital IO Function
  56
- Digital Input
  56
- Digital Output
  58
- Fast Capture
  59
- Scope
  59
- Error Display and Error History
  61
Chapter 6 Operation Mode Introduction

64
- General Steps for Starting a Control Mode
  64
- Step1: Wiring
  64
- Step 2: IO Function Configuration
  64
- Step 3: Set Necessary Parameters
  66
- Step 4: Save and Reboot
  67
- Step 5: Start Operation
  67
- Velocity Mode (-3, 3)
  67
- DIN Speed Mode
  68
- Torque Mode(4)
  68
- Position Mode(1)
  69
- DIN Position Mode Introduction
  69
- Position Table Mode
  71
- Pulse Mode(-4)
  73
- Pulse Mode Setting Steps
  74
- Other Function
  75
- Electronic Gear Ratio Switching (Expert Mode)
  76
- 4Master-Slave Mode
  76
- Full Closed Loop Mode
  77
- 1Full Closed Loop Control Operation Steps
  79
- Homing Mode(6)
  81
- Other Functions
  87
- Limit Function
  87
- Motor Brake Control
  88
- Stop Mode Control
  89
- Absolute Encoder Motor Configuration
  91
Chapter 7 Performance Regulation

95
Chapter 8 Alarm Investigation

107
- Chatper 9 Servo Panel Parameter List
  111
Chapter 10 Communication

119
- RS232 Communication
  119
- RS232 Hardware Interface
  119
- RS232 Communication Cable
  119
- RS232 Transport Protocol
  119
- RS232 Data Protocol
  120
- RS485 Communication
  123
- RS485 Hardware Wiring
  123
- RS485 Communication Parameters
  123
- MODBUS RTU Communication Protocol
  123
- Communication Troubleshooting Measures
  125
- Canopen Bus Communication
  125
- Canopen Bus Communication Hardware Description
  126
- Canopen Bus Communication Software Description
  127
- Canopen Bus Communication Settings
  134
- Interpolation Mode Based on Canopen
  136
Appendix 1: Braking Resistor Selection

137
Appendix II: List of Common Object Parameters

138
- Mode and Control（0X6040
  138
- Measurement Data
  139
- Target（0X607A
  139
- Multi-Segment Position/Multi-Segment Velocity（0X2020
  140
- Performance Object（0X6065
  141
- Homing Control（0X6098
  142
- Velocity Loop Parameters（0X60F9
  142
- Position Loop Parameters（0X60Fb
  142
- Input/Output Port Parameter（0X2010
  143
- Pulse Input Parameters（0X2508
  145
- Parameters for Storage（0X2Ff0
  145
- Error Code (0X2601)
  146
- Stop Mode
  147
- Other Parameter
  148

Kinco Categories

Controller Servo Drives DC Drives Recording Equipment Control Unit

More Kinco Manuals

Kinco FD5 Series Manuals

Kinco FD5 Series Manual (206 pages)

Table of Contents

Chapter 1 Servo System Model and Configuration Description

Chapter 2 Servo System Installation Requirements and Notes

Chapter 3 Installation and Wiring

Chapter 4 Controller Setup with LED Panel

Chapter5 Kincoservo +, User Guide

Chapter 6 Operation Modes and Control Modes

Chapter7:Tuning of The Servo System Control

Chapter 8 Alarm Investigation

Chapter 9 List of FD5 Motor Controller Parameters

Chapter 10 Communication

Appendix 1: Braking Resistor Selection

Appendix II: List of Common Object Parameters

Kinco FD5 Series User Manual (148 pages)

Table of Contents

Chapter 1 Servo System Model and Configuration Description

Chapter 2 Servo System Installation Requirements and Notes

Chapter 3 Servo System Interface and Wiring

Chapter 4 Digital Panel Operation

Chapter5 Kincoservo + User Guide

Chapter 6 Operation Mode Introduction

Chapter 7 Performance Regulation

Chapter 8 Alarm Investigation

Chapter 10 Communication

Appendix 1: Braking Resistor Selection

Appendix II: List of Common Object Parameters

Related Products

Kinco Categories