KEPCO ATE 55-20DMG Manuals

Manuals and User Guides for KEPCO ATE 55-20DMG. We have 1 KEPCO ATE 55-20DMG manual available for free PDF download: Operator's Manual

KEPCO ATE 55-20DMG Operator's Manual

KEPCO ATE 55-20DMG Operator's Manual (98 pages)

ATE-DMG Series

Brand: KEPCO | Category: Power Supply | Size: 1.51 MB

Table of Contents

Power Supply
1
Declaration of Conformity
3
Safety Instructions
5
Table of Contents
7
Section 1- Introduction

17
- Scope of Manual
  17
- General Description
  17
- Specifications
  17
- Local Control
  17
- Remote Control
  17
  - Input Characteristics
    18
  - Output Characteristics
    18
  - Physical Characteristics
    19
- Features
  21
- Overvoltage/Overcurrent Protection
  21
- Programmable Overvoltage/Overcurrent Delay
  21
- Crowbar Circuit
  22
- Non-Volatile Storage of Programmed Sequences or Active Settings
  22
- User-Defined Voltage/Current Limits
  22
- Equipment Supplied
  22
- Accessories
  22
- Safety
  22
Section 2 - Installation

25
- Unpacking and Inspection
  25
- Terminations and Controls
  25
- Source Power Requirements
  29
- Cooling
  30
- Preliminary Operational Check
  30
- Installation
  31
- Grounding
  31
- A-C (Safety) Ground
  31
- Isolation from Ground
  31
- Fast Mode Conversion of the Ate Power Supply
  31
- Precautions
  32
- Lag Network Adjustment
  32
- Crowbar Operation, Fast Mode
  32
- Manual Change-Over, Slow/Fast Mode
  32
- Operating Configuration
  33
Section 3 - Operation

35
- General
  35
- Safety Grounding
  35
- D-C (Output) Grounding
  35
- Power Supply/Load Interface
  36
- Load Wire Selection
  36
- Load Connection
  37
- General
  37
- Load Connection, Method I (Local Error Sensing)
  39
- Load Connection, Method II (Remote Error Sensing)
  39
- Load Connection, Method III
  40
- Overvoltage Crowbar, Setup and Check
  41
- Setup and Check Procedure
  41
- Local Mode Operation (Keypad Operation)
  41
- Front Panel Keypad and LCD
  42
- Command Entry Status
  42
- Data Entry Status
  42
- Display (LCD)
  42
- Keypad Functions
  42
- Turning the Power Supply on
  44
- Setting Local Mode
  45
- Adjusting LCD Contrast
  45
- Enabling/Disabling Audible Beeps
  45
- Enabling/Disabling DC Output Power
  45
- Reset
  45
- Setting Output Voltage or Current
  46
- Setting Overvoltage or Overcurrent Protection
  46
- Changing Protection Delay
  47
- Changing Maximum Voltage or Current Value
  47
- Storing Power Supply Output Settings
  47
- Recalling Stored Output Settings
  48
- Enabling Remote Analog Control
  48
- Local Mode Programming of the Power Supply
  48
- Creating or Modifying a Program (Program Edit Mode)
  48
- Modifying Programmed Time Interval
  48
- Time Interval Accuracy
  49
- Display Program Option
  49
- Running a Program
  49
- Stepping through a Program
  49
- Cycling a Program
  49
- Running a Program Once
  51
- Stopping a Program
  51
- Stopping a Running Program
  51
- Sample Program
  51
- Calibration
  51
- Analog Remote Programming
  52
- Digital Remote Mode Programming
  53
- IEEE 488 (GPIB) Bus Protocol
  53
- DCL Control
  55
- Changing the GPIB Address
  55
- Enabling Remote Analog Control
  55
- Programming Techniques to Optimize Performance
  55
- SCPI Programming
  56
- SCPI Messages
  56
- Common Commands/Queries
  56
- SCPI Subsystem Command/Query Structure
  56
- Abort Subsystem
  57
- DIAG Subsystem
  57
- Display Subsystem
  57
- Initiate Subsystem
  57
- LIST Subsystem
  57
- Measure Subsystem
  57
- Output Subsystem
  57
- Protection Subsystem
  57
- Status Subsystem
  57
- Trigger Subsystem
  58
- Source:]Voltage and [Source:]Current Subsystems
  58
- Calibrate Subsystem
  58
- Program Message Structure
  58
  - System Subsystem
    59
  - Instrument Subsystem
    59
- Keyword
  60
- Keyword Separator
  60
- Query Indicator
  60
- Data
  60
- Data Separator
  60
- Message Unit Separator
  60
- Root Specifier
  60
- Message Terminator
  62
- Understanding the Command Structure
  62
- Program Message Syntax Summary
  63
- SCPI Program Examples
  63
Section 4 - Calibration

65
- General
  65
- Equipment Required
  65
- Calibration Procedures
  65
- Voltage Calibration
  66
- Current Calibration
  66
- Changing the Calibration Password
  67
- Restoring Previous Calibration Values
  68
- Restoring Factory Calibration Values
  68
Appendix A - Ieee 488.2 Command/Query Definitions

69
Appendix B - Scpi Command/Query Definitions

75

Advertisement

Advertisement

Related Products

KEPCO Categories

Power Supply

Power Supply Adapter Battery Charger Recording Equipment Protection Device

More KEPCO Manuals