Genesys GEN100-33 Manuals

Manuals and User Guides for Genesys GEN100-33. We have 1 Genesys GEN100-33 manual available for free PDF download: User Manual

Genesys GEN100-33 User Manual

Genesys GEN100-33 User Manual (82 pages)

GEN 3.3kW SERIES POWER SUPPLIES

Brand: Genesys | Category: Power Supply | Size: 5 MB

Table of Contents

Table of Contents
6
Limitation of Warranty
10
Trademark Information
10
Fcc Notice
11
Regulatory Notices
11
Safety Instructions
12
Chapter 1 General Information

15
- Introduction
  15
- Accessories
  17
  - General
    17
  - Serial Link Cable
    17
  - Misc. Hardware
    17
  - AC Cables
    17
Chapter 2 Specifications

18
- Output Rating
  18
- Input Characteristics
  18
- Constant Voltage Mode
  18
- Analog Programming and Monitoring
  18
- Programming and Readback
  19
- Protective Functions
  19
- Front Panel
  19
- Environmental Conditions
  19
- Mechanical
  19
- Safety/Emc
  19
- Supplemental Characteristics
  20
- Outline Drawings
  21
Chapter 3 Installation

22
- General
  22
- Preparation for Use
  22
- Initial Inspection
  22
- Rack Mounting
  22
  - To Install the Power Supply in a Rack
    22
  - Rack Mount Slides
    23
- Location Mounting and Cooling
  23
- Ac Source Requirements
  23
- Ac Input Power Connection
  23
  - AC Input Connector
    24
  - AC Input Cord
    24
  - AC Input Wire Connection
    24
- Turn-On Checkout Procedure
  25
  - General
    25
  - Prior to Operation
    25
  - Constant Voltage Check
    26
  - Constant Current Check
    26
  - OVP Check
    26
  - UVL Check
    26
  - Foldback Check
    27
  - Address Setting
    27
  - Baud Rate Setting
    27
- Connecting the Load
  27
- Local and Remote Sensing
  34
  - Local Sensing
    34
  - Remote Sensing
    35
  - J2 Sense Connector Technical Information
    35
- Repackaging for Shipment
  35
Chapter 4 Front and Rear Panel Controls and

36
- Introduction
  36
- Front Panel Controls and Indicators
  36
- Rear Panel
  38
- Rear Panel Sw1 Setup Switch
  39
- Rear Panel J1 Programming and Monitoring Connector
  41
  - Making J1 Connections
    41
Chapter 5 Local Operation

43
- Introduction
  43
- Standard Operation
  43
  - Constant Voltage Mode
    43
  - Constant Current Operation
    43
  - Automatic Crossover
    44
  - Over Voltage Protection (Ovp)
    44
  - Setting the OVP Level
    44
  - Activated OVP Protection Indications
    44
  - Resetting the OVP Circuit
    44
- Under Voltage Limit (Uvl)
  45
  - Setting the UVL Level
    45
- Foldback Protection
  45
  - Setting the Foldback Protection
    45
  - Resetting Activated Foldback Protection
    45
- Output On/Off Control
  45
- Output Shut-Off (So) Control Via Rear Panel J1 Connector
  45
- Enable/Disable Control Via Rear Panel J1 Connector
  46
- CV/CC Signal
  46
- Ps_Ok Signal
  46
- Safe Start and Auto-Restart Modes
  47
  - Automatic Start Mode
    47
  - Safe Start Mode
    47
  - Over Temperature Protection (Otp)
    47
- Last Setting Memory
  47
- Series Operation
  47
  - Series Connection for Increased Output Voltage
    48
  - Series Connection for Positive and Negative Output Voltage
    49
- Parallel Operation
  50
- Daisy-Chain Connection
  52
- Front Panel Locking
  52
Chapter 6 Remote Analog Programming

53
Chapter 7 Rs232 & Rs485 Remote Control

57
- Introduction
  57
  - Configuration
    57
  - Default Setting
    57
  - Address Setting
    57
  - RS232 or RS485 Selection
    57
  - Baud Rate Setting
    57
  - Setting the Unit into Remote or Local Mode
    57
  - RS232/458 Port at Local Mode
    58
  - Front Panel in Remote Mode
    58
- Rear Panel Rs232/485 Connector
  58
  - Multi Power Supplies Connection to RS232 or RS485 Bus
    60
- Communication Interface Protocol
  60
  - Data Format
    60
  - Addressing
    60
  - End of Message
    60
  - Command Repeat
    60
  - Checksum
    60
  - Acknowledge
    60
  - Error Message
    61
  - Backspace
    61
- Error Messages
  61
- Command Set Description
  61
  - General Guides
    61
  - Command Set Categories
    61
  - Initialization Control Commands
    62
  - ID Control Commands
    62
  - Output Control Commands
    62
  - Global Output Commands
    64
  - Status Control Commands
    65
- Status, Error and Srq Registers
  66
  - General
    66
  - Conditional Registers
    66
  - Service Request: Enabled and Event Registers
    67
- Serial Communication Test Set-Up
  70
Chapter 8 Isolated Analog Programming Option

71
Chapter 9 Maintenance

74
- Introduction
  74
- Units under Warranty
  74
- Periodic Maintenance
  74
- Adjustment and Calibration
  74
- Parts Replacement and Repairs
  74
- Troubleshooting
  74
- Fuse Rating
  75
- User Manual Index
  76

Advertisement

Advertisement

Related Products

Genesys Categories

Indoor Furnishing

Indoor Furnishing Enclosure

Power Supply

Power Supply Automobile Accessories

More Genesys Manuals