Genesys GEN 1500W SERIES Manuals

Manuals and User Guides for Genesys GEN 1500W SERIES. We have 1 Genesys GEN 1500W SERIES manual available for free PDF download: User Manual

Genesys GEN 1500W SERIES User Manual

Genesys GEN 1500W SERIES User Manual (76 pages)

Programmable Regulated Power Supplies

Brand: Genesys | Category: Power Supply | Size: 3 MB

Table of Contents

Declaration of Conformity
3
Table of Contents
4
Safety Instructions
9
Chapter 1 General Information

13
- Introduction
  13
  - General Description
    13
  - Models Covered
    13
  - Features and Options
    13
  - Multiple Output Power System
    14
  - Control Via the Serial Communication Port
    14
  - Analog Voltage Programming and Monitoring
    14
  - Parallel Operation
    14
  - Output Connections
    14
  - Cooling and Mechanical Construction
    15
- Accessories
  15
  - General
    15
  - Serial Link Cable
    15
  - Misc. Hardware
    15
  - AC Cables
    15
  - Serial Port Cables
    15
Chapter 2 Specifications

17
- Protective Functions
  17
- Front Panel
  17
- Environmental Conditions
  17
- Mechanical
  17
- Safety/Emc
  17
- Supplemental Characteristics
  18
- Outline Drawings
  19
Chapter 3 Installation

20
- General
  20
- Preparation for Use
  20
- Initial Inspection
  20
- Rack Mounting
  20
  - To Install the Power Supply in a Rack
    20
  - Rack Mount Slides
    21
- Location Mounting and Cooling
  21
- Ac Source Requirements
  21
- Ac Input Power Connection
  21
- Turn-On Checkout Procedure
  23
  - General
    23
  - Prior to Operation
    23
  - Constant Voltage Check
    24
  - Constant Current Check
    24
  - OVP Check
    24
  - UVL Check
    24
  - Foldback Check
    25
  - Address Setting
    25
  - Baud Rate Setting
    25
- Connecting the Load
  25
- Local and Remote Sensing
  32
  - Local Sensing
    32
  - Remote Sensing
    33
  - J2 Sense Connector Technical Information
    33
- Repackaging for Shipment
  33
Chapter 4 Front and Rear Panel Controls and Connectors

34
- Introduction
  34
- Front Panel Controls and Indicators
  34
- Rear Panel
  36
- Rear Panel Sw1 Setup Switch
  37
- Rear Panel J1 Programming and Monitoring Connector
  39
  - Making J1 Connections
    39
Chapter 5 Local Operation

41
- Introduction
  41
- Standard Operation
  41
  - Constant Voltage Mode
    41
  - Constant Current Operation
    41
  - Automatic Crossover
    42
- Over Voltage Protection (Ovp)
  42
- Under Voltage Limit (Uvl)
  43
  - Setting the UVL Level
    43
- Foldback Protection
  43
  - Setting the Foldback Protection
    43
  - Resetting Activated Foldback Protection
    43
- Output On/Off Control
  43
- Output Shut-Off (So) Control Via Rear Panel J1 Connector
  43
- Enable/Disable Control Via Rear Panel J1 Connector
  44
- CV/CC Signal
  44
- Ps_Ok Signal
  44
- Safe Start and Auto-Restart Modes
  45
  - Automatic Start Mode
    45
  - Safe Start Mode
    45
- Over Temperature Protection (Otp)
  45
- Last Setting Memory
  45
- Series Operation
  45
  - Series Connection for Increased Output Voltage
    46
  - Series Connection for Positive and Negative Output Voltage
    47
- Parallel Operation
  48
  - Basic Parallel Operation
    48
  - Advanced Parallel Operation
    48
  - Daisy-Chain Connection
    50
  - Front Panel Locking
    50
    
    Unlocked Front Panel
    50
    
    Locked Front Panel
    50
Chapter 6 Remote Analog Programming

51
Chapter 7 Rs232 & Rs485 Remote Control

55
- Introduction
  55
- Configuration
  55
  - Default Setting
    55
  - Address Setting
    55
  - RS232 or RS485 Selection
    55
  - Baud Rate Setting
    55
  - Setting the Unit into Remote or Local Mode
    55
  - RS232/458 Port at Local Mode
    56
  - Front Panel in Remote Mode
    56
- Rear Panel Rs232/485 Connector
  56
  - Multi Power Supplies Connection to RS232 or RS485 Bus
    58
- Communication Interface Protocol
  58
  - Data Format
    58
  - Addressing
    58
  - End of Message
    58
  - Command Repeat
    58
  - Checksum
    58
  - Acknowledge
    58
  - Error Message
    59
  - Backspace
    59
- Error Messages
  59
- Command Set Description
  59
  - General Guides
    59
  - Command Set Categories
    59
  - Initialization Control Commands
    60
  - ID Control Commands
    60
  - Output Control Commands
    60
  - Global Output Commands
    62
  - Status Control Commands
    63
- Status, Error and Srq Registers
  64
  - General
    64
  - Conditional Registers
    64
  - Service Request: Enabled and Event Registers
    65
- Serial Communication Test Set-Up
  68
Chapter 8 Isolated Analog Programming Option

69
Chapter 9 Maintenance

72

Advertisement

Advertisement

Related Products

Genesys Categories

Indoor Furnishing

Indoor Furnishing

Power Supply

Power Supply Enclosure Avionics Display

More Genesys Manuals