Feig Electronic OBID i-scan ID ISC.LR200 Series Manuals

Manuals and User Guides for Feig Electronic OBID i-scan ID ISC.LR200 Series. We have 2 Feig Electronic OBID i-scan ID ISC.LR200 Series manuals available for free PDF download: Manual, Montage, Installation

Feig Electronic OBID i-scan ID ISC.LR200 Series Manual (174 pages)

Standard-Reader Firmware-Version 5.04 and Higher

Brand: Feig Electronic | Category: Card Reader | Size: 1 MB

Table of Contents
3
Revision History of Documentation

9
Abbreviations

11
1 Introduction

12
- The OBID I-Scan ® ID ISC.LR Reader
  12
2 Data Transmission between OBID I-Scan ® ID ISC.LR-Reader and Host

13
- Configuration Commands, Control Commands
  13
- ISO15693 Host Commands
  14
- Buffered Read Mode
  17
- Scan Mode
  18
- Reader Multiplex Mode
  20
- Asynchronous Interface
  21
  - Data Format and Protocol Frames
    21
  - CRC16 Calculation Algorithm
    22
3 Configuration Parameters (CFG)

23
- CFG0: Passwords
  25
- CFG1: General Inputs / Outputs
  26
  - Dedicated Input / Output Functions
    28
- CFG2: COM-Interface
  29
- CFG3: RF-Interface I
  32
- CFG4: RF-Interface II
  34
- CFG5: RF-Interface III
  35
- CFG6 + CFG7: Selection Mask (Only I-Code EPC Transponder)
  35
- CFG8: General Transponder Parameters
  36
- CFG9: Reserved
  41
- CFG10: General System Parameters
  42
- CFG11: Buffered Read Mode
  45
- CFG12: Scan Mode
  49
  - Magnetic Strip Emulation
    55
  - Wiegand Emulation
    56
- CFG13: Anticollision
  57
- CFG14: Reserved
  59
- CFG15: Antenna Multiplexing
  60
4 Protocols for Reader Configuration

62
- 0Xa0] Reader-Login
  62
- 0X80] Read Configuration
  63
- 0X81] Write Configuration
  64
- 0X82] Save Configuration to EEPROM
  65
- 0X83] Set Default Configuration
  66
- 0X85] Set System Timer
  67
- 0X86] Get System Timer
  67
5 Protocols for Reader Control

68
- 0X52] Baud Rate Detection
  68
- 0X55] Start Flash Loader
  68
- 0X63] CPU Reset
  68
- 0X65] Get Software Version
  69
- 0X66] Get Reader Info
  71
- 0X69] RF Reset
  73
- 0X6A] RF ON/OFF
  74
- 0X6C] Set Noise Level
  75
- 0X6D] Get Noise Level
  75
- 0X6E] Reader Diagnostic
  76
- 0X6F] Base Antenna Tuning
  78
- 0X71] Set Output
  79
  - Set Output Examples
    81
- 0X74] Get Input
  81
6 Special Commands

82
7 Protocols for ISO15693 Host Commands

84
- 0Xb0] Host Commands for ISO15693 Mandatory and Optional Commands
  85
  - 0X01] Inventory
    86
  - 0X02] Stay Quiet
    88
  - 0X22] Lock Multiple Blocks
    89
  - 0X23] Read Multiple Blocks
    90
  - 0X24] Write Multiple Blocks
    92
  - 0X25] Select
    94
  - 0X26] Reset to Ready
    95
  - 0X27] Write AFI
    96
  - 0X28] Lock AFI
    97
  - 0X29] Write DSFID
    98
  - 0X2A] Lock DSFID
    99
  - 0X2B] Get System Information
    100
  - 0X2C] Get Multiple Block Security Status
    102
  - 0Xa0] Read Config Block
    103
  - 0Xa1] Write Config Block
    104
- 0Xb1] Host Commands for ISO15693 Custom and Proprietary Commands
  105
  - Fujitsu Custom Commands
    106
    
    0Xa0] EAS
    106
    
    0Xa1] Write EAS
    107
    
    0Xa2] Refresh
    108
  - Infineon Custom Commands
    109
    
    0X10] Read
    109
    
    0X30] Write
    110
    
    0X90] Write Byte
    111
  - KSW Custom Commands
    112
    
    0Xa0] Set Passive
    112
    
    0Xa1] Set Log
    113
    
    0Xa2] Get Log Status
    114
    
    0Xa3] bist
    115
    
    0Xa4] Lock
    116
    
    0Xa5] Unlock
    117
  - Custom Commands for Philips ISO15693 Transponder I-Code SLI
    118
    
    0Xa2] Set EAS
    118
    
    0Xa3] Reset EAS
    118
    
    0Xa4] Lock EAS
    119
    
    0Xa5] EAS Alarm
    120
    
    0Xa0] Inventory Read
    121
  - ST Microelectronics Custom Commands
    123
    
    0Xa0] Activate EAS
    123
    
    0Xa1] Deactivate EAS
    124
- 0Xbf] ISO15693 Transparent Command
  125
- Supported ISO15693 Host Commands for ISO15693-Transponders
  128
  - Emmicroelectronics
    128
    
    Emmicroelectronics (EM4034)
    128
    
    Emmicroelectronics (EM4135)
    129
  - Fujitsu
    130
    
    Fujitsu (MB89R116)
    130
    
    Fujitsu (MB89R118)
    131
    
    Fujitsu (MB89R119)
    132
  - Infineon
    133
    
    Infineon (My-D Page Mode) 0X60
    133
    
    Infineon (ISO Address Mode) 0Xe0
    134
    
    Infineon (My-D Light)
    135
  - KSW Microtec (Tempsens)
    136
  - Philips
    137
    
    Philips (I-Code SLI)
    137
    
    Philips (I-Code SLI-S)
    138
  - Stmicroelectronics
    139
    
    Stmicroelectronics (LRI512)
    139
    
    Stmicroelectronics (LRI64)
    140
    
    Stmicroelectronics (Lri2K)
    141
  - Texas Instruments
    142
    
    Texas Instruments (Tag-It HF-I)
    142
    
    Texas Instruments (Tag-It HF-I Pro)
    144
- Supported ISO15693 Host Commands for I-Code 1 Transponders
  145
- Supported ISO15693 Host Commands for EPC Transponders
  146
- Supported ISO15693 Host Commands for I-Code UID Transponders
  147
- Supported ISO15693 Host Commands for Tag-It HF Transponders
  148
8 Protocols for Buffered Read Mode

149
- The Buffered Read Mode Procedure
  149
- Transponder Access in the Buffered Read Mode
  150
- 0X21] Read Buffer
  151
- 0X31] Read Data Buffer Info
  153
- 0X32] Clear Data Buffer
  154
- 0X33] Initialize Buffer
  154
Annex

155

Feig Electronic OBID i-scan ID ISC.LR200 Series Montage, Installation (50 pages)

Reader Module

Brand: Feig Electronic | Category: Control Unit | Size: 0 MB

Deutsch

5
- Table of Contents
  5
- 2 Leistungsmerkmale des Readers ID ISC.LR200-A/B
  
  8
  - Leistungsmerkmale
    8
  - Verfügbare Readertypen
    8
  - Lieferumfang
    9
- 3 Montage und Anschluß
  
  10
  - Anschlußklemmen und Bedienelemente
    11
  - Antennenanschluß
    12
  - Versorgungsspannung
    13
  - X7: Eingänge (Optokoppler)
    14
  - X6: Ausgänge (Optokoppler)
    15
  - X11: Relais
    16
  - X18: Anschluß Externer Diagnose-LED
    17
  - X9: RS485-Schnittstelle
    18
  - X10: RS232-Schnittstelle
    19
- 4 Bedien- und Anzeigeelemente
  
  20
  - Led
    20
  - Taster / Schalter
    21
- 5 Inbetriebnahme
  
  22
  - Schnittstellenkonfiguration Mittels Jumper
    22
  - Adresseinstellung für Busbetrieb
    23
English

29
- Features of the ID ISC.LRM200-A/B Reader Module
  
  32
  - Features
    32
  - Available Reader Types
    32
  - Delivery
    33
- Mounting and Connection
  
  34
  - Connection Terminals and Operational Control Elements
    35
  - Antenna Connection
    36
  - Supply Voltage
    37
  - X7: Inputs (Optocoupler Isolated)
    38
  - X6: Output (Optocoupler Isolated)
    39
  - X11: Relay
    40
  - X18: Connection of External Diagnostic LED
    41
  - X9: RS485 Interface
    42
  - X10: RS232 Interface
    43
- Control and Display Elements
  
  44
  - Led
    44
  - Buttons / Switches
    45
- Initialization
  
  46
  - Interface Configuration Via Jumper
    46
  - Address Configuration for Bus Mode
    47

Feig Electronic Categories

Rfid Systems Control Unit Antenna Card Reader Security Sensors

More Feig Electronic Manuals

Feig Electronic OBID i-scan ID ISC.LR200 Series Manuals

Feig Electronic OBID i-scan ID ISC.LR200 Series Manual (174 pages)

Table of Contents

Revision History of Documentation

Abbreviations

1 Introduction

2 Data Transmission between OBID I-Scan ® ID ISC.LR-Reader and Host

3 Configuration Parameters (CFG)

4 Protocols for Reader Configuration

5 Protocols for Reader Control

6 Special Commands

7 Protocols for ISO15693 Host Commands

8 Protocols for Buffered Read Mode

Annex

ANNEX A: Codes of Transponder Types

ANNEX B: Time Behavior of the Asynchronous Interface

ANNEX C: Time Behavior of ISO15693 Host Commands

ANNEX D: Index of Status Bytes

ANNEX E: Index of Control Bytes

ANNEX F: Index of Configuration Parameters

ANNEX G: Memory Model I-Code 1 Transponders

ANNEX H: Examples for Read Data

ANNEX I: Codes of Reader Types

Feig Electronic OBID i-scan ID ISC.LR200 Series Montage, Installation (50 pages)

Table of Contents

Deutsch

2 Leistungsmerkmale des Readers ID ISC.LR200-A/B

3 Montage und Anschluß

4 Bedien- und Anzeigeelemente

5 Inbetriebnahme

English

Features of the ID ISC.LRM200-A/B Reader Module

Mounting and Connection

Control and Display Elements

Initialization

Related Products

Feig Electronic Categories