User Manuals: EUCOL U2829 Series Precision LCR Meter

User Manuals: EUCOL U2829 Series Precision LCR Meter

Manuals and User Guides for EUCOL U2829 Series Precision LCR Meter. We have 1 EUCOL U2829 Series Precision LCR Meter manual available for free PDF download: Operation Manual

EUCOL U2829 Series Operation Manual

EUCOL U2829 Series Operation Manual (122 pages)

Brand: EUCOL | Category: Measuring Instruments | Size: 0 MB

Table of Contents

Table of Contents
2
Fuse
6
Out of Box Audit
6
Power Connection
6
To Inspect the Package
6
Environment
7
Use of Test Fixture
7
Warm-Up
7
Other Features
8
Chapter 2 Introduction

9
- Introduction to Front Panel
  9
- Introduction to Rear Panel
  11
- Introduction to Display Zone
  12
- Main Menu Keys and Corresponding Displayed
  12
- Meas]
  12
- Setup]
  13
- System]
  14
- Basic Operation
  14
- Start the Instrument
  14
Chapter 3 Introduction to [DISP]

16
- Meas Display
  16
- Test Function
  17
- Test Range
  18
- Test Frequency
  19
- Test Level
  20
- DC Bias
  21
- Test Speed
  21
- Tools
  22
- Bin Display
  22
- Comparator Function
  23
- Func
  24
- Nominal
  24
- Bin
  24
- High/Low
  24
- Count
  24
- Aux
  24
- Out
  24
- List Sweep Disp
  25
- Sweep Mode
  26
- FREQ (Hz)
  26
- Ls[H] Q[ ]
  26
- COMP (Compare)
  27
- Measure Setup
  27
- Trigger Mode
  28
- Auto Level Control Function
  29
- Bias Current Isolation Function
  29
- Average
  30
- Level Monitor Function
  30
- Delay Time
  31
- Output Impedance
  31
- Deviation Test Function
  32
- Correction
  33
- Open
  34
- Short
  35
- Load
  36
- Load Correction Test Function
  38
- Cable Length Selection
  39
- Single/ Multi Correction Mode
  39
- Limit Table
  39
- Swap Parameter
  40
- Limit Modes of Compare Function
  40
- Set Nominal Value of Tolerance Mode
  41
- Comparator Function ON/OFF
  42
- Auxiliary bin ON/OFF
  42
- High/Low
  43
- List Setup
  44
- Mode
  45
- Test Parameter
  45
- Sweep Parameter Setup
  45
Chapter 4 [SYSTEM] and <FILE MANAGE

46
- System Setup
  46
- Main Func
  46
- On Beepers
  47
- Pass Beep
  47
- Fail Beep
  47
- Language
  48
- Pass Word
  48
- BUS MODE (Reserved Function)
  49
- BUS ADDR (Reserved Function)
  49
- Fetch Mode
  49
- Bias Src
  50
- Baud Rate
  50
- Data/Time
  51
- System Information
  51
- Firmware Update
  51
- System Test
  52
- Lcr <File Manage
  53
- Setup File for Single-Group Component (*.STA)
  53
- U-Disk Manage Performance
  55
- Operation Steps for File Management
  55
Chapter 5 Execute LCR Operation and some Examples

57
Chapter 6 Performance and Test

67
- Test Function
  67
- Parameter and Symbol
  67
- Test Combination
  67
- Mathematical Operation
  67
- Equivalent Mode
  67
- Range
  67
- Trigger
  67
- Delay Time
  68
- Connection Modes of Test Terminals
  68
- Test Speed (Frequency>=10Khz)
  68
- Average
  68
- Display Digit
  68
- Test Signal
  68
- Test Signal Frequency
  68
- Signal Mode
  69
- Test Signal Level
  69
- Output Impedance
  69
- Monitor for Test Signal Level
  69
- Maximum Measurement Display Range
  69
- DC Bias Voltage Source
  70
- Diode Test
  70
- Measurement Accuracy
  70
- Accuracies of │Z│,│Y│, L, C, R, X, G, B
  70
- Accuracy of D
  71
- Accuracy of Q
  71
- Accuracy of Θ
  71
- Accuracy of G
  71
- Accuracy of Rp
  72
- The Accuracy of Rs
  72
- Accuracy Factor
  72
- Accuracy of DCR
  75
- Accuracy of Leakage Inductance Lk
  75
- Accuracy of the Rate of Turns to Ratio
  75
- Safety Requirement
  76
- Insulation Resistance
  76
- Insulation Intensity
  76
- Leakage Current
  76
- Electromagnetic Compatibility
  76
- Performance Test
  76
- Working Condition
  76
- The Used Instruments and Devices
  76
- Function Check
  77
- Test Signal Level
  77
- Frequency
  77
- Measurement Accuracy
  78
- Accuracy of C and D
  78
- Accuracy of L
  78
- Accuracy of Z
  78
- Accuracy of DCR
  79
Chapter 7 Command Reference

80
- Subsystem Commands for U2829
  80
- Display Subsystem Commands
  80
- Frequency Subsystem Commands
  83
- Voltage Subsystem Commands
  83
- Current Subsystem Commands
  83
- Amplitude Subsystem Commands
  84
- Output Resister Subsystem Commands
  84
- Output Subsystem Commands
  85
- BIAS Subsystem Commands
  86
- Function Subsystem Commands
  87
- LIST Subsystem Commands
  91
- Aperture Subsystem Commands
  94
- Trigger Subsystem Commands
  95
- Fetch? Subsystem Commands
  96
- Correction Subsystem Commands
  99
- Comparator Subsystem Commands
  105
- Mass Memory Subsystem Commands
  110
- TRAN Subsystem Commands
  110
- GPIB Common Commands
  120

Advertisement

Advertisement

Related Products

EUCOL Categories

Measuring Instruments Test Equipment

More EUCOL Manuals