DH Instruments RPM4 - VERSION 2004 Manuals

Manuals and User Guides for DH Instruments RPM4 - VERSION 2004. We have 1 DH Instruments RPM4 - VERSION 2004 manual available for free PDF download: Operation And Maintenance Manual

DH Instruments RPM4 - VERSION 2004 Operation And Maintenance Manual

DH Instruments RPM4 - VERSION 2004 Operation And Maintenance Manual (150 pages)

Reference Pressure Monitor

Brand: DH Instruments | Category: Monitor | Size: 2 MB

Table of Contents

Table of Contents
3
Tables

7
A B O U T T H I S M a N U al

9
1 Introduction

11
2 Installation

17
- Unpacking and Inspection
  17
  - Removing from Packaging
    17
  - Inspecting Contents
    17
  - Table 2. RPM4 Packing List
    17
- Site Requirements
  18
- Setup
  18
  - Preparing for Operation
    18
  - Front and Rear Panels
    18
  - Front Panel
    18
  - Figure 1. Front Panel
    18
  - Rear Panel
    19
  - Power Connection
    19
  - 85 To 264 Vac, 50/60 Hz Vac Power
    19
  - Battery Pack
    19
  - Figure 2. Rear Panel
    19
  - Remote [Ent] Connection (Footswitch or Other Switch)
    20
  - Connecting to Measure Pressure (Test(+) and Test(-) Ports)
    20
  - The Vent or Atm Port
    21
  - Check/Set Security Level
    21
  - Turn off Absolute and Negative Gauge Mode (Axxx Rpt)
    22
  - Sds Full Time off
    22
  - Parallel Measurement Mode
    22
- Power-Up and Verification
  22
- Short Term Storage
  24
3 O P E R a T I O

25
- Operation
  25
- User Interface
  25
  - Main Run Screen
    25
  - Figure 3. MAIN RUN Screen Display Fields
    26
  - Function / Data Keypad Layout and Protocol
    27
  - Figure 4. Keypad Layout
    27
  - Remote [Ent] (Enter) Footswitch
    28
  - Sounds
    28
- General Operating Principles
  28
- Direct Function Keys
  35
  - Range]
    35
  - Table 5. Summary of RPM4 Function Key Operation
    35
  - Unit]
    36
  - Mode]
    37
  - Differential Measurement Mode Operation
    39
  - Autorange]
    40
  - Table 6. Settings Made by Autorange
    41
  - Leak Ck]
    43
  - Display]
    44
  - Avg (Average)
    46
  - Rate
    47
  - Dev (Deviation)
    48
  - Rpt
    49
  - Hi/Lo
    50
  - Freeze
    51
  - Clean
    51
  - Head]
    52
  - Sds] (Self Defense System)
    53
  - Sds in Differential and Parallel Measurement Modes
    56
  - Autoz]
    56
  - Autoz] in Gauge and Negative Gauge Mode
    57
  - Autoz] in Absolute Mode
    58
  - Autoz in Differential Mode
    61
  - Ent] (Run Autotest)
    61
- Setup]
  62
  - 1Range
    62
  - Saving an Autorange Range
    62
  - Deleting Autorange Ranges
    63
  - 2Res> (Resolution)
    63
  - 3Stab
    64
  - 4Ul> (Upper Limit)
    65
  - Over Pressure Function
    67
  - 5Atest
    67
- Special]
  67
  - 1Autoz
    68
  - Table 7. Autoz on and off
    70
  - Edit Autoz
    72
  - 2Remote
    72
  - 1Com1, 2Com2
    73
  - 3Ieee-488
    73
  - 4Format
    73
  - 5Rs232 Self-Test
    74
  - 3Head
    74
  - 4Sds
    75
  - 1Temp Open/Close
    75
  - 2Full Time On/Off
    76
  - 5Prefs
    76
  - 1Scrsvr
    77
  - 2Sound
    77
  - 3Time
    77
  - 4Id
    78
  - 5Level> (Security)
    78
  - Table 8. Security Levels
    80
  - 6Punit
    81
  - Table 9. UNIT Function - Available Units of Measure
    82
  - 7Internal
    83
  - 1Baro
    83
  - 3Rpt2X
    83
  - 2Readrt
    84
  - Table 10. READRT - Display Update Rates
    84
  - 4Lo Vnt
    86
  - 5Log
    87
  - 8Cal
    87
  - 9Reset
    88
  - 1Sets
    88
  - Units
    89
  - 3Atest
    89
  - Cal
    89
  - Table 11. Reset - Sets
    89
  - All
    90
  - Table 12. Reset - Cal
    90
  - Table 13. Reset - All
    90
  - Remote Operation
    91
4 Remote Operation

91
- Overview
  91
- Interfacing
  91
  - Rs232 Interface
    91
  - Com1
    91
  - Table 14. COM1 Pin Designations and Connections
    91
  - Ieee-488
    92
  - Com2
    92
- Programming Formats
  92
- Commands
  95
- Status Reporting System
  118
  - Error Queue
    118
  - Status Byte Register
    118
  - Table 18. 8 Bit Status Byte Register
    118
  - Figure 6. Status Register Schematic
    119
  - Standard Event Register
    120
  - Ready Status Register
    120
  - Table 19. 8 Bit Standard Event Register
    120
  - Table 20. 8 Bit Ready Status Register
    120
- Ieee Std. 488.2 Common and Status Program Messages
  121
  - Table 21. Program Message List
    121
  - Program Message Descriptions
    122
5 Maintenance, Adjustments a N D C a L I B R a T I O

125
6 T R O U B L E S H O O T I N

141
7 A P P E N D I

141
- Table 27. Troubleshooting Guide
  141
  - 7. Appendix
    145
  - Figure 10. Remote [ENT] Connector Schematic
    145
  - Remote [Ent]
    145
  - Unit Conversion
    146
    
    Pressure
    146
    
    Table 28. Pressure Unit of Measure Conversion Coefficients
    146
    
    Warranty
    147
8 Warranty

147
- Overview
  147
- Table 29. DHI Authorized Service Providers
  147
9 G L O S S Ar

149

Advertisement

Advertisement

Related Products

DH Instruments Categories

Controller Measuring Instruments Racks & Stands Cables and connectors Accessories

More DH Instruments Manuals