Consilium CFD5000 T/CM2.2 Manuals

Manuals and User Guides for Consilium CFD5000 T/CM2.2. We have 1 Consilium CFD5000 T/CM2.2 manual available for free PDF download: Installation & Commissioning Manual

Consilium CFD5000 T/CM2.2 Installation & Commissioning Manual

Consilium CFD5000 T/CM2.2 Installation & Commissioning Manual (110 pages)

Fire Detection System

Brand: Consilium | Category: Security Sensors | Size: 5 MB

Table of Contents

Table of Contents
3
1 Introduction

9
- About this Manual
  9
- References
  10
- Symbols Used in the Manual
  10
2 Safety Considerations

11
- If a Fire or Fault Alarm Is Flashing on the Control Panel
  11
  - In Case of a Fire Alarm
    11
  - In Case of a Fault Alarm
    11
  - Further Instructions
    11
- Precautionary Measures
  12
3 Fire Detection System

13
- System Description
  13
  - Introduction
    13
  - Systems and Interfaces
    13
    
    CCP Fire
    13
    
    CFD5000 FDS - an Extension of CCP Fire
    14
    
    CFD5000 FDS Subsystem
    15
- System Data
  17
4 Prerequisites for Installation

19
5 Electrical Installation

21
- Recommended Installation Order
  21
- Cabling and Electrical Installation
  21
  - EMC Requirements
    21
  - Cable Requirements
    23
  - Loop Lengths
    24
  - Loops
    26
  - Cable Types
    26
  - Protective Earthings
    26
  - Location of Electrical Equipment
    27
- Electrical Installation, Central Equipment
  27
6 Mechanical Installation

29
- Control Panels
  29
- Loop Units
  29
- Loop Units Installation Guidelines
  29
  - General Comments When Installing Fire Detectors
    29
  - Fluorescent Light Sources
    30
  - Smoke Detectors
    30
  - Aspiration Detectors
    31
  - Heat Detectors
    31
  - Flame Detectors
    31
  - Installations in Hazardous (Ex-Classified) Location/Area
    32
    
    Intrinsically Safe Detector for Hazardous Areas
    32
  - Line Heat Detectors
    33
  - Address Units
    33
  - Manual Call Points
    33
  - Electrical Siren
    34
  - Short Circuit Isolator (SCI)
    34
- Setting the Address on Loop Units
  34
- Installation Examples for Loop Units
  35
  - Base Plate
    35
    
    General Information
    35
    
    Mounting of UB-6 Base Plate
    36
    
    Dismounting of UB-6 Base Plate
    36
  - CS-PYH Detector
    36
    
    Mounting of CS-PYH Detector to Base
    36
    
    Dismounting of CS-PYH Detector from Base
    37
  - CS-ASP Aspirating Smoke Detector
    37
    
    Mounting of CS-ASP
    38
    
    Dismounting of CS-ASP
    38
- Mechanical Installation Examples for DIN Rail Components
  39
  - DIN Rail
    39
    
    Mounting of DIN Rail
    39
    
    Dismounting of DIN Rail
    39
  - Modules on a DIN Rail
    40
    
    Mounting of Modules on a DIN Rail
    40
    
    Dismounting of Modules on a DIN Rail
    41
  - DIN Rail Module Support
    41
    
    Mounting of DIN Rail Module Support
    42
    
    Dismounting of DIN Rail Module Support
    42
  - DIN Carrier
    42
    
    Mounting of SLZ-2 DIN Carrier
    43
    
    Dismounting of SLZ-2 DIN Carrier
    43
  - DCDC Converter
    44
    
    Mounting of MTM PCMDS DCDC Converter
    44
    
    Dismounting of DCDC Converter
    45
7 Pre-Commissioning

47
- Inspection
  47
- Test the Loop Cable
  48
- Check the Loop Units
  52
- Commissioning Requirements
  53
  - Prerequisites for Commissioning
    53
  - Proof Test
    53
- Loops (Control Panel CM2.2)
  54
  - Central Status
    54
  - Verification of Loops
    54
- Setting Address and Layout on Repeater M4.3
  55
- Testing of System Parts (Control Panel CM2.2)
  56
  - Prerequisites for Testing
    56
  - About Testing
    57
  - Recommended Test Equipment and Procedures
    57
    
    Approved Test Equipment
    57
    
    Heat Detectors
    57
    
    Smoke Detectors
    58
    
    Aspirating Smoke Detectors
    59
    
    Flame Detectors
    60
    
    Manual Call Points
    60
  - Test the Control Module Display
    61
- Troubleshooting
  62
  - Prerequisites for Troubleshooting
    62
  - Wrong Number of Loop Units
    63
  - Cable Break
    64
  - Earth Fault
    65
  - Short Circuit
    65
  - Muting Faults
    66
  - Reset Faults
    66
  - Save the System Log to a USB Memory Stick
    66
  - Save the bist Log to a USB Memory Stick
    67
  - How to Report a Fault
    68
- Configuration Setup for Control Panel CM2.2
  68
  - Configuration Overview
    68
  - Choose Configuration
    68
  - Distribute Configuration Files
    69
9 Safety Validation and Acceptance

71
10 Fault Codes

73
- Fault Codes for CFD5000
  73
11 Address List and Test Report

87
12 Appendix A

89
- 12 Appendix A ID List
  89
- Prerequisite
  89
- Setting the ID
  89
- SSP Termination
  89
  - General Recommendations for Installation of SSP
    89
  - 13 Appendix B
    91
13 Appendix B

91
- System Modules & Connection Example
  91
14 Appendix C

94
- Definitions and Abbreviations
  94
15 Appendix D

101
- The Consist ID
  101

Advertisement

Advertisement

Related Products

Consilium Categories

Gas Detectors Security System Measuring Instruments Fire Alarms Data Loggers

More Consilium Manuals