CODEL GCEM4000 In-Situ Gas Analyzer Manuals

Manuals and User Guides for CODEL GCEM4000 In-Situ Gas Analyzer. We have 1 CODEL GCEM4000 In-Situ Gas Analyzer manual available for free PDF download: Technical Manual

CODEL GCEM4000 Technical Manual

CODEL GCEM4000 Technical Manual (65 pages)

Multi-Gas Analyser

Brand: CODEL | Category: Measuring Instruments | Size: 5 MB

Table of Contents

Section 1

5
- Table of Contents
  5
- CODEL GCEM4000 Analyser - Introduction
  7
- Foreword
  7
- Figure 1 : Typical Smartcem System Arrangement
  7
- GCEM4000 Basic Principles
  8
- Figure 2 :GCEM4000 Analyser with 'In-Situ' Probe
  8
- Emission Monitoring and the GCEM4000
  9
- Normalisation
  9
- Verification
  9
- User Interface
  9
- Analogue and Logic Inputs and Outputs
  9
- CDC Serial Port - for Use with the CODEL Smartcem System
  10
- Analyser Protection
  10
- Summary Specification
  11
- Preparing for Installation
  13
- Unpacking
  13
- The Basic Analyser
  13
- Figure 3 : Standard Supplied Items and Dimensions
  13
- Transceiver Weather Cover
  14
- Additional Materials
  14
- Figure 4 : Active Weather Cover
  14
- Figure 5 : CODEL Supplied Connections
  15
- Ancillary/Additional Equipment
  16
- Services
  16
- Installation
  17
- Selection of Measurement Position
  17
- Analyser Positioning
  18
- Figure 6 : Preferred Transceiver Position
  18
- Figure 7 : Angled Probe Installation
  18
- Fitting of Stub-Pipes and Mounting Flanges
  19
- Figure 8 : Rectangular Ducts - Acceptable Position
  19
- Figure 9 : Spacing from Other Analysers
  19
- Figure 10 : Standard Site Mounting Flange
  20
- Concrete and Brick Stacks
  20
- Metal Ducts/Stacks
  20
- Double Skin Stacks
  21
- Installation of Purge Air Supply
  21
- Installation of Measurement Tube
  21
- Figure 11 : Typical Stub Pipe Arrangement for Concrete/Brick Stacks
  21
- Figure 12 : Beam Lifting Point
  22
- Figure 13 : Position of Pressure Sensor
  22
- Fitting the Active Weather Cover and Sensor Head
  23
- Figure 14 : Cable Gland
  28
- Installation of Normalising Measurements (Oxygen, Temperature and Pressure)
  28
- Installation and Connection of Cables
  28
- Wiring Connections
  28
- Installation of the GCU
  28
- System Connections
  29
- Figure 15 : System Connections
  29
- Figure 16 : Sensor Head Connections
  30
- Commissioning
  31
- Pre-Commissioning Checks
  31
- Power on
  31
- Initial Set-Up Using Smartcom Software
  31
- Adjust Alignment
  33
- Thermistor Control
  34
- Source Temperature Control
  36
- Cell Oven Control
  37
- Rx Temperature Check
  37
- Cell Oven Control
  38
- Figure 17 : Alignment Adjusters
  40
- Detector Levels
  42
- Zero Calibration
  42
- Current Data
  44
- Y' Values
  45
- Plant Status Set-Up
  46
- Span Verification
  47
- General Overview
  50
- Water Vapour Checks
  50
- Setting the Output Configuration
  51
- Read/Set RTC
  53
- Memory Back-Up
  55
- Analyser Records
  57
- Serial Numbers (Complete on First Inspection)
  57
- Installation Records
  57
- Commissioning Records
  57
- Automatic Zero Calibration
  58
- Manual Zero Verification
  58
- Introduction
  58
- Verification
  58
- Factory Calibration
  58
- Calibration and Measurement Verification
  58
- Comparative Testing
  59
- Re-Calibration
  59
- Maintenance
  60
- Fault Finding
  61
- Appendix 1 - Setting Analyser Gains
  64
Section 2

65
- List of Figures
  65

Advertisement

Advertisement

Related Products

CODEL Categories

Measuring Instruments

Monitor

Monitor Smoke Alarm

More CODEL Manuals