Belden grass valley GV NODE Manuals

Manuals and User Guides for Belden grass valley GV NODE. We have 2 Belden grass valley GV NODE manuals available for free PDF download: User Manual

Belden grass valley GV NODE User Manual (166 pages)

IP AGGREGATION, PROCESSING AND EDGE ROUTING PLATFORM

Brand: Belden | Category: Multi-service Platforms | Size: 17 MB

Table of Contents
13
1 Getting Started

17
2 Configuring Your GV Node

37
- User Interfaces
  37
  - Local Control Panel
    37
  - Controller's Web Page
    39
  - Icontrol
    40
- Configure the CPU-ETH3 Controller
  42
- Identification
  42
  - Identification Using Icontrol
    43
- Status Monitoring
  44
- Network Configuration
  53
- Link Redundancy
  55
- SNMP Functionality
  56
- Data Restoration
  58
- Factory Alignment
  62
- Time Management
  64
- Alarms
  66
- Local Control Panel Menu - CPU-ETH3
  69
  - Upgrading the CPU-ETH3 Controller
    70
- Configure the Frame Reference
  71
  - Reference Source
    72
  - Timecode
    73
  - URS Generation
    74
  - Alarms
    75
  - Options
    76
  - Information
    77
  - Factory Settings
    78
  - Upgrading the Frame Reference
    79
  - Menu for Local Control
    80
- Configure the IFM-2T Fabric Module
  82
  - Identification
    83
  - Status
    84
  - Options
    85
  - Port and Lane Configuration
    87
  - Stream Redundancy
    89
  - Stream Bitrate
    90
  - Stream Addressing
    90
  - Bulk Addressing Utility
    91
  - Transmit Stream Addressing - Redundancy off
    92
  - Receive Stream Addressing - Redundancy off
    93
  - Transmit Stream Addressing - Redundancy on
    96
  - Receive Stream Addressing - Redundancy on
    98
  - IGMP Mode Selection
    101
  - Lane Status Monitoring
    101
  - Lane Statistics Reporting
    102
  - RX Statistics
    103
  - TX Statistics
    105
  - Timing
    106
  - Nmos Is-04
    107
  - Alarms
    107
  - User Presets
    109
  - Factory Configuration
    110
  - Hot Swap to Maintain Routes
    110
  - Technical Support
    111
  - Edge Device Control
    112
- Configure the XIO-4901 SDI I/O Card
  112
  - The Icontrol Service Panel
    113
  - Identification
    114
  - Status
    115
  - Input Configuration - ASI
    116
  - Input Configuration - SDI
    117
  - Input Timing - SDI
    119
  - Input Status
    120
  - Input Audio
    121
  - Output Configuration - ASI
    121
  - Output Configuration - SDI
    121
  - Output Timing - SDI
    124
  - Output Status
    124
  - Output Audio
    125
  - Test
    125
  - Options
    127
  - User Presets
    128
  - Factory Configuration
    129
  - Alarms
    130
- GV Node Manager
  132
  - Terminology
    132
  - Input and Output Provisioning
    132
- Alarm Configuration
  139
- Asynchronous Video
  141
3 Router Control Configuration

145
- Introduction
  145
- Overview
  145
  - Card Slot I/O Numbering
    147
  - Aggregation Port I/O Numbering
    148
4 GV Node Audio

153
- Overview of GV Node Audio
  153
- Madi
  154
- SDI Embedded Audio
  155
- Audio under ST 2110
  157
5 Use Cases

159
- Use Cases for V1.2 and Later
  159
Contact Us

166
- Grass Valley Technical Support
  166
- Corporate Head Office
  166

Belden grass valley GV NODE User Manual (83 pages)

IP AGGREGATION, PROCESSING AND EDGE ROUTING PLATFORM

Brand: Belden | Category: Measuring Instruments | Size: 9 MB

Table of Contents
13
1 Getting Started

15
- About this Document
  15
- About GV Node
  15
  - Part Locations
    16
  - Connections
    17
- GV Node User Interfaces
  19
  - The Local Control Panel
    19
  - The Icontrol Interface
    20
  - The Controller Web Page
    21
- Networking and Control Setup
  21
- GV Node Initial Configuration
  25
2 Configuring Your GV Node

29
- CPU-ETH3 Controller User Interface
  29
  - Identification
    29
  - Status Monitoring
    31
  - Network Settings
    34
  - SNMP Functionality
    35
  - Data Restoration
    35
  - Factory Alignment
    37
  - Time Management
    38
  - Alarms
    39
- Frame Reference User Interface
  40
  - Reference
    41
  - URS Generation
    41
  - Timecode
    42
  - Alarms
    43
  - Information
    44
  - Factory Settings
    46
- IFM-2T Fabric Module User Interface
  47
  - Identification
    47
  - Status
    49
  - Options
    50
  - Port and Lane Configuration
    51
  - Transmit Stream Addressing
    53
  - Receive Stream Addressing
    54
  - Bulk Addressing Utility
    55
  - Lane Status Monitoring
    56
  - Lane Statistics Reporting
    57
  - Timing
    58
  - Alarms
    59
  - User Presets
    60
  - Factory Configuration
    61
  - Hot Swap to Maintain Routes
    62
  - Edge Device Control
    62
- XIO-4901 User Interface
  62
  - The Icontrol Service Panel
    63
  - Identification
    63
  - Status
    65
  - Input Configuration - SDI
    66
  - Input Timing
    69
  - Input Status
    69
  - Output Configuration - SDI
    70
  - Output Timing
    72
  - Output Status
    73
- GV Node Manager
  73
- Alarm Configuration
  74
- Local Control Menus
  77
  - CPU-ETH3 Menu
    77
3 Router Control Configuration

79
- Introduction
  79
- Setting up Irouter for the GV Node
  79
- Creating Logical Routers
  82
Contact Us

83

Belden Categories

Switch

Monitor Control Unit Control Panel Media Converter

More Belden Manuals

Belden grass valley GV NODE Manuals

Belden grass valley GV NODE User Manual (166 pages)

Table of Contents

1 Getting Started

2 Configuring Your GV Node

3 Router Control Configuration

4 GV Node Audio

5 Use Cases

Contact Us