Bailey INFI 90 INPPR01 Manuals

Manuals and User Guides for Bailey INFI 90 INPPR01. We have 1 Bailey INFI 90 INPPR01 manual available for free PDF download: Instruction

Bailey INFI 90 INPPR01 Instruction

Bailey INFI 90 INPPR01 Instruction (65 pages)

Plant Loop to Plant Loop Remote Interface

Brand: Bailey | Category: Recording Equipment | Size: 1.49 MB

Table of Contents

Table of Contents
7
Section 1 - Introduction

11
- Overview
  11
- Intended User
  11
- Diagram of Plant Loop to Plant Loop Remote Interfaces in Two-Way Control Mode
  11
  - Hardware Description
    12
    
    Additional Hardware
    12
    
    Bus Transfer Module (INBTM01)
    12
    
    Loop Interface Module (INLIM03)
    12
    
    Plant Loop to Plant Loop Transfer Module (INPPT01)
    12
  - Features
    12
  - Instruction Content
    13
  - How to Use this Manual
    13
  - Glossary of Terms and Abbreviations
    14
  - Reference Documents
    15
  - Nomenclature
    15
  - Specifications
    16
Section 2 - Description and Operation

17
- Introduction
  17
- Local/Remote Communications
  17
- Data Integrity
  18
- Timing Interval
  18
  - Transmit/Receive Timing
    19
- Send/Receive Timing Diagram
  20
Section 3 - Installation

21
- Introduction
  21
- Special Handling
  21
- Unpacking and Inspection
  21
- Inppt01 Switch Settings
  21
  - Option Switch (U72)
    22
- Switch Locations on the PPT (CPU Board)
  22
- Option Switch (U72) Settings
  22
  - Serial Port Communication Rate (U73)
    23
  - Loop Address (U75)
    24
- Message Throughput
  24
- U75 Loop Addresses
  24
  - Inlim03 Switch Settings
    25
- LIM Switch Locations
  25
- LIM Event Counter Addresses (SW1)
  25
- LIM Error Counter Addresses (SW1)
  26
  - Inbtm01 Switch Settings
    27
- BTM Switch (SW1) Location
  27
- LIM Node Address Setting (SW2)
  27
  - Termination Unit (Module) Configuration
    28
    
    NTMF01/NIMF01/NIMF02 Configuration
    28
    
    One-Way Control
    28
- BTM Options (SW1)
  28
- NTMF01 and NTCL01 in a Redundant Installation
  29
- NIMF01/NIMF02 and NICL01 in a Redundant Installation
  29
  - Two-Way Control
    30
  - NTCL01/NICL01 Configuration
    30
  - Installing the Interface Modules
    30
    
    Installing the INPPT01
    30
    
    Installing the INLIM03 and INBTM01
    31
  - Installing a Redundant Interface
    32
  - Interface Configuration
    32
- Redundant Transceiver
  33
- INPPR01 Function Codes
  33
Section 4 - Operating Procedures

34
- Introduction
  34
- PLANT LOOP to PLANT LOOP TRANSFER MODULE Leds and CONTROLS
  34
- PPT Faceplate Leds
  34
  - Status LED
    35
  - CPU Leds
    35
  - Memory Leds
    35
Section 4 - Operating Procedures

35
- Stop Pushbutton
  35
- Reset Pushbutton
  35
- PPT Status LED States
  35
  - LOOP INTERFACE MODULE Leds
    36
  - Bus Transfer Module Led
    36
  - Modes of Operation
    36
- LIM Faceplate Leds
  36
  - Configure Mode
    37
  - Execute Mode
    37
- BTM Faceplate Leds
  37
- BTM Status Leds States
  37
  - Error Mode
    38
  - One-Way Control
    38
  - Two-Way Control
    39
  - Redundant Interface Operation
    39
- Local and Remote Plant Loops in Two-Way Control
  39
  - Interface Point Capacity
    40
- Memory Usage in Receiving Communication
  40
  - Memory Usage Example
    41
    
    Memory Usage in the Local PPT
    41
    
    Memory Usage in the Remote PPT
    41
- Memory Usage in Sending Communication
  41
  - Security Functions
    42
    
    Hardware Checks
    42
    
    Software Checks
    42
    
    Utilities
    42
- PPT Utilities Menu
  43
Section 5 - Troubleshooting

44
Section 6 - Maintenance

49
- Introduction
  49
- Maintenance Schedule
  49
Section 7 - Repair/Replacement Procedures

50
- Introduction
  50
- Module Repair/Replacement
  50
Section 8 - Support Services

51
- Introduction
  51
- Replacement Parts and Ordering Information
  51
- Training
  51
- Technical Documentation
  51
Appendix A - Termination Unit Configuration (Ntmf01

52
- Introduction
  52
  - Dipshunt Configuration for Direct Connection with Local PPT Acting as DTE
    53
  - Dipshunt Configuration for Direct Connection with Remote PPT Acting as DCE
    54
    
    A-4. Dispshunt Configuration for Diagnostic Terminal (Port 1 Only)
    55
    
    A-5. DB-25 Pin Assignments and RS-232-C Signals
    56
Appendix B - Termination Unit Configuration (Ntcl01

57
Appendix C - Termination Module Configuration (Nimf01/Nimf02

59
- Introduction
  59
Appendix D - Termination Module Configuration (Nicl01

63
- Introduction
  63
- Jumper Settings and Cable Types
  64

Advertisement

Advertisement

Related Products

Bailey Categories

Control Unit Motorhomes Lighting Equipment Recording Equipment Controller

More Bailey Manuals