ASP STERRAD 100 Manuals

Manuals and User Guides for ASP STERRAD 100. We have 1 ASP STERRAD 100 manual available for free PDF download: Service Manual

ASP STERRAD 100 Service Manual

ASP STERRAD 100 Service Manual (309 pages)

Sterilization System

Brand: ASP | Category: Laboratory Equipment | Size: 5 MB

Table of Contents

Table of Contents

3
What's New in this Guide

10
- CHAPTER 1. About the Service Guide
  
  11
  - Introduction
    11
  - What's New in this Guide
    11
  - New for REV D
    11
  - Revision C Information
    12
  - REV A/B Information
    12
  - What's New Table
    13
Table of Contents

17
- CHAPTER 2. System Operation
  
  18
  - Introduction
    18
  - Theory of Operation-Overview
    18
  - Routine Maintenance
    19
  - Canceled Cycles
    26
  - Alarm Limits by Parameter
    27
  - Software Overview
    29
  - User Interface and Operator Controls
    32
  - Functional Subsystems
    32
  - Additional Documentation
    33
  - STERRAD 100 S Theory of Operation
    34
  - Introduction
    34
  - Phase 1 - Vacuum Preconditioning
    34
  - Phase 2 - Sterilization a
    35
  - Phase 3 - Sterilization B
    36
  - Phase 4 - Venting
    37
  - STERRAD 100 S Process Times
    37
- CHAPTER 3 Using System Messages
  
  41
  - Introduction
    41
- CHAPTER 4. Vacuum Subsystem
  
  88
  - Introduction
    88
  - Different Subsystem Configurations
    88
  - Theory of Operation
    89
  - Vacuum Pump
    89
  - Exhaust Filter
    90
  - Oil Return Valve
    90
Table of Contents

114
- Different User Subsystem Configurations
  115
- Introduction
  115
- Theory of Operation
  117
- User Interface Subsystem
  117
- Controller Operation
  120
- User Interface Calibration
  123
- Setting the Printer DIP Switches
  124
- Setting System Parameters
  125
- Setting the Audible Alarm
  125
- Setting the LCD Contrast
  125
- Setting the System Clock
  129
- Setting the System Serial Number and Total Machine Cycles
  130
- Master Reset
  131
- Controller Calibration
  132
- Power Supply Adjustment
  132
- Analog to Digital (Set Point)
  134
- High/Low Pressure Range Divider Voltage
  134
- Remove/Replace the Printer
  135
- User Subsystem Replacement Procedures
  135
- Remove/Replace the Membrane Switch
  136
- Remove/Replace the Printer (Block 2)
  136
- Control Subsystem Replacement
  137
- Remove the Control Enclosure
  137
- Remove the Power Supplies
  138
- Replace the Control Enclosure
  138
- Replace the Power Supplies
  138
- Remove/Replace the Firmware
  139
Table of Contents

141
- Different Door and Chamber Configurations
  142
- Door and Chamber Subsystem Descriptions
  142
- Introduction
  142
- Chamber Subsystem
  143
- Door and Chamber Theory of Operation
  143
- Door Subsystem
  143
- Calibration
  144
- Door and Chamber Temperature
  144
- Door Open Close Speed
  146
- Door Top, Bottom, and over Center Sensors
  146
- Door and Chamber Alignment
  147
- Removal/Replacement
  153
Table of Contents

183
- Introduction
  184
- Pre-Installation
  184
- Uncrating the System
  185
- Installing the Seismic Restraints
  191
- Pre-Installation Procedure-To be Done by the Customer
  191
- Installing the Subframe
  192
- Installing the Brackets
  193
- Phase Rotation
  194
- Preparing the System for Use
  194
- Initialization
  195
- Master Resets
  195
- Cassette Collector Box
  196
- Date and Time
  196
- PM Log
  197
- System Acceptance
  197
- International System Configurations
  198
Table of Contents

204
- Introduction
  205
- Maintenance Schedule
  205
- Level 1 Planned Maintenance
  207
- Level 2 Planned Maintenance
  212
Introduction/Certification Procedures

217
- Introduction
  218
- Certification Procedures
  220
- System Preparation
  220
- Compressor Pressure Switch Test
  221
- Power Supplies Test
  221
- Analog to Digital Set Point Test
  222
- Baratron Zero Test
  223
- High-Low Pressure Range Divider Voltage Verification
  223
- Cassette Optics Test
  225
- Injector Pump Floating Guide Check
  225
- RF Power Test
  225
- Heater Voltages and Temperatures
  226
- Leak Back Test
  226
- Master Reset
  226
- Chamber Temperature
  227
- Door Temperature
  227
- Temperature Continuity Check
  227
- Vaporizer Heater Voltage
  227
Appendix A

229
- Physical Specifications
  230
- Environmental Conditions
  231
- Electrical Requirements
  233
- Heater Impedance
  234
- Standards
  235
- Product Version
  236
- Thermocouples
  238
- Tools and Test Equipment
  238
Appendix B

240
- Introduction
  241
- Overview
  241
- Test Name
  241
- User Interface Tests
  242
- Sensor Tests
  247
- Injection and Pneumatics Tests
  253
- Throttle Valve/Heater Menus
  261
- Door Test
  266
- Analog Test
  268
- Vacuum Subsystem Tests
  272
- Cassette Adjustments
  278
- Printer Test
  281

Advertisement

Advertisement

Related Products

ASP Categories

Barcode Reader Laboratory Equipment Water Pump Toy Enclosure

More ASP Manuals