APELEM Magnum C Series Manuals

Manuals and User Guides for APELEM Magnum C Series. We have 1 APELEM Magnum C Series manual available for free PDF download: Service Manual

APELEM Magnum C Series Service Manual

APELEM Magnum C Series Service Manual (304 pages)

X-Ray Generator

Brand: APELEM | Category: Medical Equipment | Size: 4 MB

Table of Contents

Chapter 1 Pre-Installation

4
- Table of Contents
  4
- Features
  5
- Generator Description
  5
- Introduction
  5
- Environmental Specifications
  6
- Radiographic Performance
  6
- Applicable Standards
  7
- Electromagnetic Compatibility (EMC)
  11
- Rohs Compliance
  11
- Safety
  13
- Safety and Warning Symbols
  13
- Safety Notices and Warnings
  13
- Safety Warning Labels
  16
- Generator Heat Output
  20
- Generator Power Requirements
  20
- Preparing for Installation
  20
- Generator Ground Requirements
  24
- Locating and Mounting the Generator
  25
- Cable Entrance and Seismic Center Location
  26
- Tools and Test Equipment Required
  27
- Generator Layout and Major Components
  28
- Pre-Installation Checklist
  28
- Compatibility Listing
  31
- Runtime License Agreement (Touchscreen Console)
  32
- Compatibility Statement
  33
- Customer Support
  33
Chapter 2 Installation

35
- Introduction
  36
- Removing the Generator Cover
  36
- Unpacking
  36
- Control Console
  37
- Equipment Placement
  37
- Main Cabinet
  37
- Major Component Layout
  37
- Anchoring the Generator to the Floor
  39
- Wiring to the Generator
  39
- Control Console
  40
- Hand Switch (Optional)
  44
- Stator Connections
  44
- Power Line Mains
  46
- Thermal Switch
  46
- High Tension Cables
  49
- X-Ray Tube Housing Ground
  49
- Emergency Power off / Power Distribution Relay
  50
- Low Speed Starter Tube Compatibility
  50
- Room Equipment
  50
- Safety Interlocks
  50
- Setting 120 / 240 VAC Boost Voltage
  51
- EPROM Type / Dual Speed Starter
  52
- Programming the Dual-Speed Starter
  52
- Setting Tube Type
  52
- Configuring Dual Speed Starter 901297-15 / 901298-15
  55
- Auxiliary Transformer Line Voltage Tap Selection
  56
- Dip Switch Settings
  56
- Initial Run-Up
  56
- Initial Voltage Measurements
  58
- Final Checks
  59
- TUBE Ma AUTO CALIBRATION
  59
Chapter 3C Interfacing and Programming

63
- 1.0 Introduction
  65
- 2.0 Wiring to Inputs & Outputs
  65
- 2.1 Inputs
  65
- 2.2 Outputs
  66
- 2.3 Inputs & Outputs (Simplified Schematic)
  68
- 2.4 AEC Interconnect
  69
- 2.5 DR Imaging System
  69
- 3.0 Generator Programming
  69
- 3.1 Entering into Programming Mode
  69
- 4.0 Generator Setup Menu
  70
- 5.0 Utility Menu
  72
- 5.1 Setting Time and Date
  72
- 5.2 Error Log
  74
- 5.3 Statistics
  75
- 5.4 Console
  76
- Apr Editor
  80
- 7.0 Generator Configuration
  81
- 7.1 Tube Selection / Tube Setup
  81
- 7.2 Generator Limits
  91
- 7.3 Receptor Setup
  93
- 7.4 I/O Configuration
  102
- 7.5 AEC Setup
  108
- 7.6 AEC Calibration
  111
- 7.7 Tube Calibration
  111
- 8.0 Validate Apr
  112
- 10.0 Dap Interfacing
  116
- 10.1 DAP Compatibility
  116
- 9.0 Dap Printer Setup
  116
- 10.2 DAP Installation
  117
- 11.0 Dap Setup
  117
- 11.1 DAP SETUP Menu
  117
- 11.2 DAP SETUP Menu Items
  119
- 12.0 Dap Calibration
  122
- 12.2 DAP Calibration Overview
  122
- 3C12.1 Equipment Required
  122
- 12.3 DAP Calibration Procedure
  123
- 12.4 DAP Calculation Worksheet
  126
- 13.0 DATA LINK (Connect to Genware®)
  128
- 14.0 Generator Configuration Backup and Restore
  128
- Interfacing and Programming
  128
- 15.0 License Key Setup
  129
- 16.0 Monochrome Display
  130
- 17.0 Touchscreen System Utilities
  131
- 17.2 APR Editor
  134
- 17.3 APR Backup / Restore
  137
- 17.4 Date / Time Setup
  140
- 17.6 Touchscreen Setup
  144
- 17.7 Touchscreen Calibration
  147
- 17.8 Data Link
  147
- 17.9 Configuration Backup / Restore
  148
- 17.10 Touchscreen Console Firmware Upgrade / Restore
  150
Chapterd Aec Calibration

161
- AEC Board (Solid State Chambers)
  163
- Chapter 1 2.2
  
  165
- CHAPTER 3 AEC Board (Ion Chambers)
  
  165
- Chapter 4 2.3
  
  167
  - AEC Board (Ion Chambers)
    167
  - 2.4
    169
  - AEC Board (5-Field Ion Chambers)
    169
  - Precalibration Notes
    171
  - Aec Density Calibration
    171
  - Aec Calibration (Wall Bucky)
    176
  - Aec Calibration (Misc)
    188
  - Aec Overview and Background Information
    190
  - Film/Screen Response Vs
    192
  - AEC Calibration Range
    192
  - Precalibration Setup
    192
  - AEC Setup Worksheet
    192
  - 9.1
    193
Chapter 4 Acceptance Testing

197
- Introduction
  198
- Required Test Equipment for Generator Verification
  199
- Acceptance Tests (Basic Functions)
  200
- Console Tests
  200
- Low Speed Starter Verification
  201
- ACCEPTANCE TESTS (Kv, Ms, Ma and Mas)
  202
- Dual Speed Starter (Optional) Verification
  202
- Generator Rad Tests
  202
- Acceptance Tests (Aec)
  206
- Acceptance Tests (Dap)
  207
- Acceptance Tests (Dr Interface)
  207
- Acceptance Tests (Hvl, Linearity and Reproducibility)
  207
Chapter 5 Troubleshooting

209
- Introduction
  210
- Limit Messages
  211
- Operator Messages
  211
- Status and Error Codes
  211
- Error Messages
  213
- Erratic Console Faults
  223
- Miscellaneous Faults
  223
- Dual Speed Starter Board
  224
- Generator Control Board
  224
- HV Auxiliary Board
  224
- Led Indicators
  224
- AEC Board
  225
- EMC Capacitor Board
  225
Chapter 6 Regular Maintenance

227
- Introduction
  228
- Maintenance Schedule
  228
- Oil Fill / Level Check
  232
- Cleaning
  233
- Console Firmware
  234
- Firmware Upgrade
  234
- Generator Firmware
  236
- Dual Speed Starter EPROM
  237
- Resetting Factory Defaults
  237
- Aec Board Remova Land Installation
  239
- Battery Replacement
  239
- Tube Conditioning / Seasoning
  239
- Tube Conditioning
  240
- End of Product Life
  241
Chapter 7 Theory of Operation

243
- Functional Theory of Operation
  244
- Introduction
  244
- System on (MD-0928)
  244
- DC Bus & Power Distribution (MD-0927)
  245
- Room Interface (MD-0930)
  246
- X-Ray Exposure (MD-0931)
  246
- Kv Control and Feedback (MD-0932)
  248
- Filament Drive and Ma Control (MD-0934)
  249
- Dual-Speed Starter (MD-0924)
  250
- Low-Speed Starter (MD-0935)
  251
- Dap (MD-0938)
  252
- Serial Communications (MD-0937)
  252
- Temp Sensor / Programming Jumpers (MD-0925)
  252
- Aec (MD-0936)
  253
- Digital Interface (MD-0926)
  257
- Interconnect Diagram (MD-0939)
  258

Advertisement

Advertisement

Related Products

APELEM Magnum C DR Series

APELEM Categories

Medical Equipment

More APELEM Manuals