Angelus 180S Manuals

Manuals and User Guides for Angelus 180S. We have 1 Angelus 180S manual available for free PDF download: Service Notices

Angelus 180S Service Notices (82 pages)

Brand: Angelus | Category: Industrial Equipment | Size: 21 MB

Service Notice Numbering and Tracking System
1
Complete Oil Change, 180S Seamer
3
Oil Refill Process
7
Ceramic Ball Bearing Assembly
8
Seaming Roll with Ceramic Bearing Assembly
9
Installation Sequence for 180S Seamers
9
Service Notice
10
Lube Line Diversion
12
Lubricator Assembly
13
S854 Feed Sprocket Guard Modification
14
262S854 Feed Sprocket Guard Modification
15
180S Seamers - Filler Drive Safety Clutch Oil Seal (26S815)
16
Model 180S Main Drive Shaft Locknut 192S816 Requirements
17
Knockout Pad Adjustment Procedures
18
Adjusting Umbrella Style Knockout Pads
18
Variable Speed Inching Mechanism
20
Limiter Devices
20
View of Variator Is from the Output Shaft End
20
Model 180S Idler Gear Assembly Procedure
21
Adjusting Seamer Brake and Filler Brake
22
Angelus Customer Service Department
23
Model 180S Main Drive Motor Alignment Procedure
24
Angelus Fixture J-13695 Attachment
24
Motor Installation
25
Dial Indicator Setup & Adjustment Parameters
25
Dial Set for Aligning the Face Reading
26
Motor Installed with Coupling Guard
26
Model 180S Seamer System Operation and Control Logic
27
Filtration System Information
29
Trabon Oil System General Information
29
Trabon System Information
29
Oil Lubrication System Continued
30
Oil Lubrication System
31
Oil Pump Push on Push off Button
31
Change Oil Filter Light
31
Trabon Refill on Light
32
High Oil Pressure Switch
32
Warning Oil Pressure Switch N.C.
32
Oil Flow Switch
32
Refill-Boost Solenoid
33
Seamer Oil Lubrication System Timers
33
Trabon Cycle Fault Timers
33
Optional Automatic Grease Lubrication System
34
Operation and Control Logic for 180S Seamers
34
Automatic Grease Lubrication General
34
Automatic Grease Lubrication Operation
34
Automatic Grease Control Logic Operation
35
Manual Grease Check Button Operation
35
Pre-Wash and Post Wash Operation
35
Variable Speed Inching Mechanism General Information
35
Variable Speed Inching Mechanism System Operation
36
Reversing Starter and Motor Operation
36
Inching Mechanism Clutch Operation
36
Filler Drive / Seamer Safety Clutch System
36
Filler Drive / Seamer Safety Clutch System Operation
37
Stationary Field Tooth Clutch Operation
37
Standby Power Supply Operation
37
Filler Drive Clutch Control Logic Operation
37
Can Proximity Sensor Operation
38
Flag Proximity Sensor Operation
38
Cover Feed Solenoid Operation
38
Solid State Relay Operation
38
Dual Speed Undercover Gassing System Operation
39
Flow Meter Operation
39
Digital Display Operation
39
Solenoid Valves Operation
39
Undercover Gassing Control Logic Operation
40
Crt Control Startup & Operation
41
Start-Up and Operation
41
Main Power
42
Control Power
42
Basic Crt Overview
42
Crt Page Explantion
43
Cell Descriptions and Operation
43
Start/Stop Seamer
43
Speed Change
43
Seamer Brake
44
Seamer Speed Display
44
Filter Pump Select
44
Door Enabled Wash-Jog- Run
44
Inch/Run Operation
45
Inch
45
Control Reset
45
Gas System
45
Message Display
46
Filler Drive Clutch
46
Ac Motor Drive
46
Turret Infeed
46
Hold down Bar
47
Discharge Rail
47
Discharge Gate
47
Feed Chain Clutch
47
Oil Filter System
48
Door Interlocks
48
Grease Sytem
48
Jam Stops
49
Jog/Run Operation
49
Jog
49
Discharge Table Assembly
50
Discharge Table Breakdown
51
180S Seamer Discharge Table
52
Remove the Base Side Cover
52
Discharge Column Support Removal Located under the Seamer
53
Release the Discharge Turret Gear from the Turret Hollow Shaft
54
Discharge Turret Gear Removal
54
Separate the Discharge Hollow Shaft from the Discharge Turret Gear
55
Discharge Turret Gear Ready for Removal
56
Install Column and Discharge Turret Hollow Shaft
57
Discharge Turret Gear & Discharge Turret Hollow Shaft Assembly
58
Complete Assembly of Discharge Table
59
Reset Upper Turret Housing Height
60
Install and Time Can Size Change Parts
61
Seaming Spindle
62
Service Notice
68
Replace Existing 2S854 Oil Guard
71
Tools Required
72
Remove Old Style 2S854 Oil Guard
73
Installation
75
Retrofitting Rotary Union Shield P/N 197S854
77
Installation Procedure
77
323S854 Oil Baffle
78
Model 140S and 180S Seamers
79

Angelus Categories

Personal Care Products Measuring Instruments Industrial Equipment

More Angelus Manuals

Angelus 180S Manuals

Angelus 180S Service Notices (82 pages)

Table of Contents

Related Products

Angelus Categories