Electrolux EI30BM60MS Installation Instructions Manual page 72
Over the range microwave oven
Hide thumbs
Also See for EI30BM60MS:
- Use and care manual (28 pages) ,
- Installation instructions manual (24 pages) ,
- Product specifications (5 pages)
Table of Contents
Advertisement
Available languages
Available languages
REMARQUE: IL EST TRÈS IMPORTANT DE LIRE ET DE
RESPECTER LES INSTRUCTIONS D'INSTALLATION AVANT
D'UTILISER CE GABARIT POUR MUR ARRIÈRE.
Ce gabarit sert à d terminer l'emplacement de l'ouverture du conduit
é
d' vacuation horizontal.
é
1. Utilisez un niveau pour vérifier que le gabarit est positionné
précis ment.
é
2. Repérer et marquer au moins un montant sur la gauche ou la
droite de la ligne médiane.
REMARQUE: Il est important d'utiliser au moins une
vis à bois fermement montée dans un montant pour
supporter le poids du micro-onde. Marquez deux autres,
emplacements,uniformément espacées, pour les boulons
à ailettes fournis.
3. Percez des trous aux emplacements marqués. Là où il y a
un montant, percez un trou de 3/16 po pour les vis à bois.
Pour les trous qui ne s'alignent pas avec un montant, percez
un trou de 5/8 po pour les boulons à ailettes.
REMARQUE: NE FIXEZ PAS LA PLAQUE DE MONTAGE
IMMEDIATEMENT.
4. Enlevez le gabarit du mur arrière.
5. Reportez-vous aux inst
ructions
d'inst
allation
étapes suivantes.
Turun over for English
Localiser et marquer les trous à aligner avec les trous dans
la plaque de montage.
IMPORTANT:
LOCALISEZ AU MOINS UN MONTANT SUR CHAQUE CÔTÉ DE
LA LIGNE MÉDIANE.
MARQUEZ L'EMPLACEMENT POUR DEUX AUTRES BOULONS À AILETTES,
UNIFORMÉMENT
ESPACÉES, DANS LA ZONE DE LA PLAQUE DE MONTAGE.
Coupez le gabarit pour le mur arrière le long de la ligne pointillée.
Part No.: 316495140
Part No.:7 7 2 2 2
3 16902477
PN: 2618003 9832
1
pour les
NOTE:
IT IS
NOTE:
IN THE
READ AND
BEFORE
REAR WALL
TEMPLATE.
PROCEEDING
INSTALLATION
FOLLOW
THE DIRECTIONS
WITH THIS
VERY IMPORTANT
TO
INSTRUCTIONS
READ AND
REAR WALL
BEFORE
IN THE
VERY IMPORTANT
PROCEEDING
FOLLOW
IT IS
INSTALLATION
INSTRUCTIONS
THE DIRECTIONS
TO
mounting
outlet.
1. Use
This Rear
Wall Template
plate
accurately.
a level
serves
and to
locate
to check
that the
the horizontal
to position
the bottom
exhaust
12"
3/8" TO EDGE
mounting
outlet.
1. Use
This Rear
TEMPLATE.
Wall Template
plate and
a level
the horizontal
serves
to locate
WITH THIS
to position
the bottom
12"
3/8" TO EDGE
2. Locate
of the
locations
screw
important
microwave.
It is
side of
mounted
and mark
right
firmly
to use
in a stud
the centerline.
at least
template
one stud
on the
at least
one wood
left or
is positioned
4"
accurately.
2. Locate
right side
screw mounted
to check
and mark
of the
It is important
that the
at least
one stud
to use
centerline.
on the
is positioned
template
left or
exhaust
4"
3. Drill
that do
not line
a stud,
holes
for the
toggle
drill
bolts.
up with
a 3/16"
Mark two
supplied
in the
marked
locations.
wood screws.
a stud,
hole for
bolts.
toggle
additional,
to support
Where
spaced
evenly
the weight
there
is
Trim the
rear wall
template
a stud,
3. Drill
that do
of the
locations
for the
microwave.
supplied
firmly
holes in
the marked
Mark two
drill a
locations.
toggle
3/16" hole
in a stud
additional,
the weight
to support
at least
evenly
one wood
bolts.
spaced
Trim the
rear wall
template
along
the dotted
AT THIS
4. Remove
5. Review
the template
TIME.
DO NOT
the Installation
installation
INSTALL
from the
THE MOUNTING
situation.
drill
PLATE
rear wall.
Instruction
For holes
5/8" holes
for
along
the dotted
line.
5. Review
4. Remove
AT THIS
toggle
TIME.
the template
DO NOT
bolts.
not line
INSTALL
up with
a stud,
THE MOUNTING
PLATE
screws.
Where there
drill 5/8"
for wood
holes for
For holes
is
line.
Darle vuelta
versión
en Español.
a la hoja
para consultar
la
book for
your
Darle vuelta
installation
a la hoja
the Installation
situation.
Instruction
from the
book for
rear wall.
your
versión
en Español.
para consultar
la
Locate
mounting
IMPORTANT:
plate.
and mark
holes
to align
with holes
Locate
MARK THE
THE CENTERLINE.
LOCATE
LOCATION
AT LEAST
ONE STUD
ON EITHER
SIDE OF
in the
LOCATE
IMPORTANT:
mounting
and mark
plate.
AT LEAST
to align
holes
with holes
in the
SPACED
AREA.
TOGGLE
BOLTS
FOR 2
ADDITIONAL,
MOUNTING
IN THE
PLATE
EVENLY
MARK THE
SPACED
THE CENTERLINE.
LOCATION
TOGGLE
FOR 2
ONE STUD
BOLTS
ON EITHER
ADDITIONAL,
SIDE OF
Trim the
AREA.
IN THE
MOUNTING
EVENLY
PLATE
rear wall
template
along
the dotted
line.
Trim the
rear wall
template
along
the dotted
line.
Locate
mounting
and mark
holes
IMPORTANT:
THE CENTERLINE.
LOCATE
plate.
AT LEAST
ONE STUD
to align
ON EITHER
with holes
in the
mounting
and mark
Locate
IMPORTANT:
plate.
holes
to align
with holes
SPACED
AREA.
MARK THE
LOCATION
TOGGLE
BOLTS
FOR 2
IN THE
ADDITIONAL,
MOUNTING
SIDE OF
EVENLY
LOCATE
MARK THE
THE CENTERLINE.
AT LEAST
LOCATION
ONE STUD
ON EITHER
in the
SIDE OF
PLATE
TOGGLE
SPACED
AREA.
BOLTS
FOR 2
ADDITIONAL,
IN THE
MOUNTING
EVENLY
PLATE
FR-24
Coupez le gabarit pour le mur arrière le long de la ligne pointillée.
Localiser et marquer les trous à aligner avec les trous dans le
la plaque de montage.
IMPORTANT:
PLACEZ AU MOINS UN MONTANT SUR L'AUTRE CÔTÉ DE
LA LIGNE MÉDIANE.
MARQUEZ DEUX AUTRES BOULONS À AILETTES, UNIFORMÉMENT
ESPACÉES, DANS LA PLAQUE DE MONTAGE ZONE.
Imprimé en Chine
Advertisement
Chapters
Table of Contents
