Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Crypto F200
Summary of Contents for Crypto F200
- Page 1 U S E R M A N U A L F200 ADSL USB MODEM...
-
Page 3: Table Of Contents
C O N T E N T S Introduction Specifications ADSL Standards supported Supported Protocols Connections Hardware Installation Procedures Hardware Requirements Preparing your network information Configure the ISP parameters for your Windows XP Driver Installation on Windows XP Software Configuration Connection to the Internet Troubleshooting... -
Page 4: Introduction
ADSL modem with the superb reliability and is a complete solution for home and office. The F200 ADSL USB modem can have a maxi- mum downstream data rate of up to 8Mbps and an upstream of up to 1Mbps. -
Page 5: Connections
2.3 Connections USB – Connects the USB cable from the USB port of the F200 modem to the USB port of the computer. LINE – Connects the RJ11 telephone cable from the telephone line port of F200 modem to the telephone plug.. -
Page 6: Configure The Isp Parameters For Your Windows Xp
G.lite 3.3 Configure the ISP parameters for your Windows XP F200 is initially set to function on Annex B protocol (ADSL over ISDN). To install the F200 based on Annex A protocol ( ADSL over PSTN), follow the procedure below. -
Page 7: Driver Installation On Windows Xp
3.4 Driver Installation on Windows XP Step 1: Windows will detect the newly installed device and the screen below will appear after the F200 USB ADSL Modem is attached to the systems USB port. Select "Install from a specific Location", and click "NEXT". -
Page 8: Software Configuration
'Properties_ > _Device Manager' Double click on Network adapters and check to see for: 'Crypto F200 USB ADSL WAN adapter' 3.5 Software Configuration Continue the setup process of the F200. Step 1: Double click on the ‘Access Runner’ icon Step 2: Initially there is no connection / synchronization with the ADSL line ‘Attempting to Activate Line’. - Page 9 Step 3: Here you can see that the connection has not been established. ‘Attempting to Activate Line’. Click the ‘Line Setup’ tab Step 4: Initially it is set to Annex B (ADSL over ISDN) as shown on the bottom right. Note: If the line was ISDN, then we do not change it.
- Page 10 ADSL line has been done with success. Note: 1 to 2 minutes are required after you make the above configurations, in order for the F200 to be synchronized with the ADSL line. Step 10: To see information regarding the connection, click the Physical Layer Statistics tab, and click OK.
-
Page 11: Connection To The Internet
/ synchronization with the ADSL line has been done with success. Note: After power on the PC, it takes 1 to 2 minutes in order for the F200 to be synchronized with the ADSL line. 3.6 Connection to the Internet... - Page 12 Step 4: To ensure that the F200 has been successfully installed, under the General tab, check to see that Connected is indicated next to Status. You can also check your connection speed: Speed -> 448.0kbps. Step 5: Under the Details tab, you can see various information regarding the connection.
-
Page 13: Troubleshooting
4. Troubleshooting The POWER LED is not on ñCheck to see that the connections between the USB port of the F200 and the USB port of your computer are plugged in correctly. Cannot access ISP ñIf in PPPoA & PPPoE mode, check your login account and password for the remote server. -
Page 14: Declaration Of Conformity
Declaration of Conformity The 'F200 ADSL USB MODEM' is approved for use for within the European Union, and the compatibility of this unit and it’s basic requirements are declared with the CE symbol. Passage extract of the authentic declaration of conformity:... - Page 16 www.crypto.gr...